What to Do When the Changan Car Key is Locked in the Car?

How to Replace the Battery in a Ford Edge Car Key?

To replace the battery in a Ford Edge car key, follow these steps: 1. Press the clip at the end of the key and open the back cover; 2. Insert a one-yuan coin into the slot at the end and twist to separate the outer cover, revealing the key battery inside; 3. Remove the old battery and install the corresponding new one; 4. Reattach the outer cover and back cover. Taking the 2021 Ford Edge as an example, its front suspension is a MacPherson independent suspension, the rear suspension is a multi-link independent suspension, equipped with a 2.0T turbocharged engine, delivering a maximum horsepower of 245 PS, a maximum torque of 390 Nm, and a maximum power of 180 kW, matched with an 8-speed automatic transmission.

14

3

Share

Should coolant be added when it is low or completely drained and refilled?

Coolant can either be added when it is low or completely drained and refilled. The steps for replacing coolant are: 1. Open the vehicle's engine hood, and you can see the coolant reservoir in the upper right corner; 2. Open the coolant drain plug under the radiator to drain the old coolant; 3. Add new coolant, tighten the cap, and the coolant replacement is complete. Precautions for using coolant are: 1. Try to use the same brand of coolant; 2. Avoid diluting it with water; 3. When adding, ensure the product is within its validity period; 4. If a large amount of particle precipitation appears, it indicates that the coolant has deteriorated and should no longer be used.

12

1

Share

Which is larger, the intake valve or the exhaust valve?

Intake valves are larger than exhaust valves. Air intake relies on vacuum suction, while exhaust is pushed out through compression. Additionally, to allow the engine to intake more fresh air and thereby enhance the vehicle's overall power performance, naturally more intake is required, which is why the intake valve is larger. The exhaust valve does not have this requirement. More details about valves are as follows: 1. The function of a valve is specifically responsible for introducing air into the engine and expelling the exhaust gases after combustion. Structurally, valves are divided into intake valves and exhaust valves. The intake valve's role is to draw air into the engine to mix with fuel for combustion; the exhaust valve's role is to expel the burned exhaust gases and dissipate heat. 2. The size requirements for intake and exhaust valves are determined based on the engine's air intake and exhaust volumes. If the valve clearance is too small, it can lead to a decrease in the engine's power and even cause the valve to burn out. Excessive clearance is also not allowed, as it not only accelerates wear on components but also affects the cylinder's intake and exhaust conditions. Therefore, it is essential to adjust according to standard specifications.

15

3

Share

Is SN engine oil fully synthetic?

SN engine oil is fully synthetic. Fully synthetic SL-grade engine oil is not considered high-quality fully synthetic oil because there are SM and SN-grade fully synthetic oils that perform better than SL-grade. There are even better PAO-based oils, such as imported GT Magic Red engine oil, which surpasses SN-grade and is naturally superior to SL-grade synthetic oil. More details are as follows: 1. SN-grade oils are almost always fully synthetic. 2. Engine oils starting with "S" are specifically for gasoline engines and cannot be used in diesel vehicles. 3. Engine oil grades include twelve levels: SA, SB, SC, SD, SE, SF, SG, SH, SJ, SL, SM, and SN. With each ascending letter, the performance of the engine oil generally improves over the previous grade. 4. Although SN-grade engine oil performs well, it is best to use the grade specified by the engine. If the vehicle is frequently driven in congested urban environments, using a higher-grade engine oil can be more environmentally friendly.

5

3

Share

What symbol is used to represent China V vehicles?

The symbol for China V vehicle emission standards is the letter 'V'. Below is relevant information about the China V standard: 1. It is equivalent to the Euro V standard in the EU, which has been implemented since 2009, imposing strict limits on nitrogen oxides, hydrocarbons, carbon monoxide, and particulate matter emitted by motor vehicles. 2. The fifth phase of the national motor vehicle emission standard was implemented nationwide starting from January 1, 2018, while Beijing began implementing it from January 1, 2016. Below is additional information about the China V emission standard: 1. Starting from July 1, 2017, all domestically manufactured, imported, sold, and registered heavy-duty diesel vehicles must comply with the China V standard requirements. 2. After July 1, 2017, 'China IV' vehicles were not allowed to be registered in some regions. 3. Starting from 2018, China III and China IV vehicles were prohibited from being driven on the road.

11

2

Share

What Causes Water Leakage in the Car A-Pillar?

There are several reasons for water leakage in the car A-pillar: 1. Poor sealing of the window rubber strip or the fixing holes of the roof rack. 2. Aging of the rubber strip. 3. Inadequate sealing around the car door. 4. Blockage of the sunroof drainage pipe. The specific situation requires the car owner to visit a 4S shop for inspection. Once the issue is identified, the car can be repaired in the shortest possible time. More details are as follows: 1. The car A-pillar is the connecting pillar between the left/right front and the roof, located between the engine compartment and the driver's cabin, above the side mirrors. It partially obstructs the turning view, especially during left turns. The A-pillar serves to secure the front windshield, clamping the two front glass panels firmly to ensure the stability and rigidity of the car body. In the event of a frontal or oblique side collision, it effectively protects the safety of the driver and passengers. 2. Generally, the driver's overlapping angle of vision through the A-pillar is 5-6 degrees. From the perspective of driver comfort, the smaller the overlapping angle, the better—meaning the thinner the A-pillar, the better. However, designers must strike a balance, clearly prioritizing the high rigidity of the A-pillar to reduce safety risks. Therefore, from this perspective, the A-pillar is not necessarily better the smaller it is.

18

1

Share

What to Do When the Changan Car Key is Locked in the Car?

How to Replace the Battery in a Ford Edge Car Key?

Should coolant be added when it is low or completely drained and refilled?

Which is larger, the intake valve or the exhaust valve?

Is SN engine oil fully synthetic?

What symbol is used to represent China V vehicles?

What Causes Water Leakage in the Car A-Pillar?

Does the car charge the battery when starting in place?

What is the difference between Volkswagen Tiguan L National V and National VI?

What is the difference between coating agent and waxing?

Are Engine Guards and Chassis Armor the Same Thing?