···
Log in / Register

What to Do When the Annual Inspection Attachment Page Is Full?

4 Answers
StKarter
07/29/25 4:37pm

When the annual inspection attachment page is full, you should promptly go to the vehicle management office at the license plate issuance location to apply for a replacement. Below is relevant information about annual inspections: 1. Initial Annual Inspection: The inspection conducted for motor vehicles to apply for a driving license is called the initial annual inspection. The purpose of the initial annual inspection is to verify whether the motor vehicle meets the conditions for applying for a license plate. 2. Definition: According to national regulations, motor vehicles must pass regular exhaust emission tests, as well as inspections for vehicle appearance, lights, brakes, chassis, etc., and must have no traffic violation records to be issued an inspection compliance mark. All annual inspection dates are based on the registration date on the driving license. Motor vehicles must undergo safety technical inspections according to the following periods from the date of registration, commonly referred to as "annual inspection" or "annual review."

Was this review help?
10
2
Share
LeonardoMarie
08/14/25 5:57am

I've been driving for over a decade and have encountered the situation where the supplementary page of the vehicle inspection is full a few times. Each time, I simply drove to the nearby vehicle management office or inspection station to handle it. The staff could tell at a glance and helped replace the supplementary page. Just bring your ID card, driving license, and other required documents. The whole process is quite fast, taking less than half an hour to complete. Remember not to wait until the inspection is about to expire to deal with it, otherwise it may delay the formal inspection and result in a fine. I make it a habit to check how much space is left on the supplementary page every year and prepare in advance. Driving with complete vehicle documents gives me peace of mind. In short, this matter is very simple, and timely action can save a lot of trouble.

Was this review help?
12
4
Share
Expand All
VonAaron
10/13/25 2:09am

I just bought a car and soon encountered the situation where the annual inspection attachment page was full. Nervously, I looked it up and found out that I just needed to bring my vehicle license and ID card to the DMV, and they would replace the attachment page on the spot. Don’t worry about wasting time; making an appointment can speed things up. Usually, pay attention to how much of the attachment page has been used and leave some blank space. If it does get full, don’t panic—just go to a professional institution to handle it. Vehicle inspection is a big deal and shouldn’t be delayed, or it might affect your ability to drive legally. As a newbie, I find this advice super practical.

Was this review help?
10
5
Share
Expand All
VanGage
11/26/25 3:08am

A full supplementary page must never be ignored, as it affects the safety of your vehicle's annual inspection records. Any issues discovered during inspection could cause significant delays. I immediately went to the designated station to replace the supplementary page, bringing all necessary documents to get it done quickly and ensure everything was processed correctly. Delays could pose substantial risks, so it's crucial to avoid potential fines or accident hazards. Consistently checking and maintaining the status of your supplementary page is essential.

Was this review help?
15
5
Share
Expand All
More Forum Discussions

How to Reactivate ETC After Detachment?

Methods to reactivate ETC after detachment: 1. Insert and remove the ETC card twice consecutively until the electronic tag screen displays 'Bluetooth On' or directly press the button on the top of the electronic tag to activate Bluetooth; 2. Turn on Bluetooth on your phone, open the app mini-program, download the corresponding mobile app based on the electronic tag's brand, and enter the device activation interface; 3. Click 'Device Connection', select the device model to be connected, and patiently wait for the successful connection prompt; 4. After successful connection, follow the prompts to verify and upload a photo of the vehicle's front face to complete activation. Wait for 3 to 5 days for review, and it can be used normally after approval.
19
1
Share

Is the Tire Ruined After Driving a Distance Without Air?

Not necessarily. However, it is not recommended to continue driving with low tire pressure. The specific consequences are as follows: Consequences: Driving with insufficient air pressure can cause excessive flexing of the tire body, which generates high heat. The inner liner rubber may burn into black spots, leading to separation between the rubber and the tire cord fabric. In more severe cases, the inner liner rubber may melt due to high heat, causing structural damage to the tire. Safety Hazards: Continuing to drive with weakened tire strength may eventually lead to tire failure or even a blowout, posing significant safety risks.
8
3
Share

What is the appropriate tire inflation pressure for sedans?

Tire inflation pressure is generally maintained at 2.2-2.5 bar, which is considered appropriate. In summer, it should be slightly lower. Effects of abnormal tire pressure: Excessive tire pressure reduces the friction and adhesion of the tires, increases the risk of tire blowouts, and affects driving safety. Insufficient tire pressure not only causes steering difficulties and vehicle deviation, which are detrimental to driving safety, but also damages the tires. Seasonal factors affecting tire pressure: In winter, it is advisable to increase the standard tire pressure by approximately 0.2 bar. In summer, follow the lower limit of the standard tire pressure. For vehicles parked outdoors in summer, the pressure can generally be about 0.1 bar lower than the standard to prevent high-temperature blowouts.
2
5
Share

What is the rod connecting the wheels called?

The rod connecting the wheels is called the car suspension. Definition of car suspension: The suspension system refers to all the force-transmitting connection devices between the car frame and the axle or wheels. Its function is to transmit forces and torques between the wheels and the frame, buffer the impact from uneven roads to the frame or body, and dampen the resulting vibrations to ensure smooth driving. Non-independent suspension system: The structural feature of a non-independent suspension system is that the wheels on both sides are connected by an integral axle, and the wheels together with the axle are suspended under the frame or body through an elastic suspension system.
20
0
Share

Will an Electric Car Stall When Wading Through Water?

It can stall. Generally, deep water wading primarily tests the sealing of car doors and the passenger compartment. Additionally, electric vehicles have specified wading depths, and exceeding them is not recommended. Below are the reasons: Poor Sealing Solutions: The sealing of the power output shaft. If the water level exceeds the power output shaft, water can quickly enter the transmission and then the motor. Short Circuit: Power sources, cables, and inverters. If the water level is too high, these components are prone to short circuits because water can enter through any gaps. Poor Contact: The electrical control system and sensor lights in cars typically use traditional connectors. After being submerged in water, they may experience poor contact and short circuit issues.
2
4
Share

What are the reasons why a car won't start in cold weather?

The reasons why a car won't start in cold weather are: 1. The car battery is dead; 2. Low temperature causes the viscosity and rotation speed of the engine oil to decrease; 3. There is a problem with the ignition system; 4. Insufficient fuel in the car; 5. Excessive carbon deposits inside the vehicle's engine; 6. The fuel pump is damaged, preventing fuel in the fuel tank from being supplied for combustion. The solutions for a car that won't start are: 1. Check if the battery is dead; 2. Check if the fuel pump is damaged; 3. Check if there is sufficient fuel; 4. Check if the engine sensors are damaged; 5. Check if there is a problem with the ignition system; 6. Use a heating rod to warm up the engine oil.
13
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.