What to do when sonaroff is flashing?

1 Answers
Adam
07/29/25 4:40pm
sonaroff flashing indicates that the ultrasonic positioning system is turned off, which means all the vehicle's radars are deactivated. You can try restarting the vehicle to resolve this issue. This situation usually occurs due to poor contact in the reverse radar wiring. Taking the car to a repair shop to fix the wiring connection will solve the problem.
Was this review help?
2
4
Share
More Forum Discussions

How to Turn on Both Front and Rear Fog Lights on a Skoda?

The difference between the front and rear fog light symbols is that there is a vertical wavy line passing through the light beam line, but the front fog light symbol's beam line points downward, while the rear fog light's is parallel. Using high beams is not recommended because the high beam light scatters and reflects diffusely in rainy or foggy conditions. Additionally, when turning on the fog lights, it is essential to reduce your speed to prevent accidents. The rear fog light can only be turned on when the headlights or front fog lights are already on. The rear fog light cannot be turned on individually; it must be activated simultaneously with the front fog light.
14
3
Share

How to restart the Skoda central control screen?

You can first turn off the vehicle, wait for a short while, and then restart it. Alternatively, locate the power button on the central control to restart it. You can also check if there are any loose connections in the wiring. If the central control screen remains black, it could also be a power signal failure. Then, inspect the power signal cable, as it is prone to aging. Replacing it usually resolves power signal issues.
6
1
Share

What are the solutions for the loud noise in the Leopaard CS10 panoramic sunroof?

The solutions for the loud noise in the Leopaard CS10 panoramic sunroof are: 1. Lack of lubrication in the sunroof guide rails, which can be resolved by applying some lubricant; 2. Loose screws inside the sunroof, which can be fixed by tightening them; 3. Increased gaps between sunroof components causing noise, which can be addressed by installing buffer washers. The Leopaard CS10 is the flagship model of Leopaard Motors in the urban SUV segment, with a body size of 4719mm in length, 1875mm in width, and 1700mm in height, and a wheelbase of 2700mm. It is equipped with a 2.0T engine, delivering a maximum power of 130kw and a peak torque of 250nm.
14
5
Share

How to adjust the valves on a four-cylinder Cummins 16-valve engine?

Four-cylinder 16-valve clearance adjustment mnemonic: Rotate to the top dead center of cylinder one, follow the sequence 1-3-4-2 (double-row non-intake), and reverse the adjustment when at the top dead center of cylinder four. Loosen the adjustment screw, use a screwdriver to turn the screw shaft, determine the correct adjustment position, tighten the screw, and adjust the intake and exhaust valve clearances. During adjustment, turn the adjustment screw while inserting a feeler gauge between the valve stem end and the rocker arm, moving it back and forth until slight resistance is felt.
14
0
Share

How to Adjust the Fuel Consumption Display on a Skoda?

First, there is a protruding small round button on the dashboard. Press and hold this button for a while to reset the dial, then remove the dashboard. After removing the dashboard, take off the upper cover of the instrument panel and remove the pointers for speed, fuel gauge, water temperature, and RPM. Then, use a flat-head screwdriver to adjust the odometer gear, which can be rolled back or reset to zero. If the odometer is a modern electronic one. At this point, reinstall the chip back into the instrument panel, and it will display the desired mileage. The simplest way to reset it to zero is to directly replace it with a new instrument panel.
8
1
Share

How to Use the Four-Wheel Drive Hub Lock?

The 'LOCK' position is the switch to immobilize the vehicle. When the car key is turned to this position, it locks the steering wheel, preventing significant movement. 'AUTO' represents automatic four-wheel drive. In automatic mode, the system will automatically adjust whether to engage the front drive, while the 'LOCK' position disables the front-wheel drive mode.
4
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.