What to Do When ORA Tire Pressure is Too Low?

1 Answers
DeArthur
07/29/25 9:07am
Check the tires to see if they have been punctured by nails and confirm whether the low tire pressure is caused by external forces. Visually inspect whether the tires can still continue to drive. If possible, drive to the nearest tire repair shop for handling. If the tire pressure is too low to drive, use the onboard air pump to inflate the tires and drive to the nearest repair shop for inspection. Replace the spare tire and reinstall the tire edge with the wheel hub. Low tire pressure caused by low temperatures is a normal phenomenon. Start the vehicle and run it for a while to restore normal tire pressure.
Was this review help?
18
5
Share
More Forum Discussions

What are the model specifications of the drive belt?

Motor belt models are divided into seven types: O-type, A-type, B-type, C-type, D-type, E-type, and F-type, with the cross-sectional area gradually increasing from O-type to F-type. Below are the precautions for motor belts: 1. When purchasing belts: The selected model should match the chosen V-belt; otherwise, the V-belt may exhibit abnormal conditions in the pulley groove. When replacing V-belts, it is best to bring the old belt to purchase to avoid model errors. 2. When replacing belts: If two or more V-belts need to be replaced, use the specified model of V-belts and ensure that the tension of each group of V-belts is consistent. Mixing old and new belts or reducing the number of belts is not allowed. Otherwise, the old and new V-belts will bear uneven force, and the old V-belts may even become ineffective, affecting power transmission and shortening the lifespan of the V-belts.
20
2
Share

Do 4S shops repair tires?

Most 4S shops do not repair tires. Here are the tire repair methods: 1. Cold and hot patching: The cold patching method uses cold patching film and glue to cover the holes on the original airtight layer. Since it is repaired directly without heating, it is called cold patching. The hot patching method also uses the above tools, but ensures the correct bonding of the adhesive under heating conditions. However, high temperatures may have some unnecessary effects on the tire rubber. 2. External patching strips for repair: This method can only repair small nail holes and is very convenient, but the service life is not long, and it will heat up and soften to prevent gas inside the tire from leaking through the nail holes. 3. Tire repair machine for repair: This is generally a tire repair and inflation all-in-one machine, which can avoid tire replacement, but it is generally only suitable for small nail holes.
7
1
Share

Does the auto-hold function damage the car?

auto-hold function does not damage the car. The automatic parking system (AUTO-HOLD) adds some functions to the electronic handbrake (HOLD), making the handbrake more user-friendly (especially for beginners). When the indicator light on the AUTO-H button is on, it means this function is activated. The working principle of automatic parking (AUTO-HOLD) is as follows: 1. The electronic handbrake simply locks and releases the rear wheels, while automatic parking applies to all four wheels. It determines whether the wheels need to be locked or released based on multiple pieces of information such as wheel speed, wheel torque, and throttle position; 2. When the wheel speed gradually decreases to zero, the automatic parking system will determine that the vehicle needs to brake, and the system will automatically lock all four wheels. At this point, you can release the foot pressing the brake pedal to relax; 3. When starting, just lightly press the accelerator pedal. After receiving signals such as throttle opening, gear position, and forward wheel torque, the automatic parking system will determine that the vehicle is about to start and will release the brake, allowing the vehicle to start normally.
11
0
Share

How to Deal with Numerous Tree Sap Dots on the Car?

Here are methods to clean tree sap from the car: 1. Soak a towel in hot water, place it on the tree sap spots on the car, wait for a while until the sap softens, then use cleaning solution to soak the towel and wipe, making the cleaning process easier. Purchase and use tree sap cleaner, spray it on the sap, then slowly wipe it off with a towel; 2. Use car cleaning clay, which not only has strong cleaning power but also a certain polishing effect. However, this method is generally suitable for small areas, as cleaning large areas can be more labor-intensive; 3. Use alcohol for cleaning. Alcohol can effectively dissolve tree sap. Dipping a towel in alcohol and wiping the sap can easily remove it. If tree sap drips onto the car, the above methods can effectively clean it off. However, after removal, it's best to wax and polish the paint surface to better protect it. Especially when using car cleaning clay or cleaning agents, these methods may slightly damage the paint surface. Otherwise, over time, the paint surface may become dull and lose its luster.
12
1
Share

How Many Chances Are There for the Driving Test Subject 3 Exam?

Subject 3 exam can be scheduled 5 times, with one main exam and one retake opportunity for each scheduled session, totaling 10 chances. If both opportunities in the first scheduled exam are missed, the exam should be rescheduled after 10 days. Below is relevant information about retake scheduling: 1. The ranking is based on the time of the previous exam; for Subject 1, it is based on the registration time; 2. For Subject 1 exam, passing it in one attempt generates a priority ranking for Subject 2 exam; failing Subject 1 generates a priority ranking for retaking Subject 1; 3. For Subject 2 exam, the ranking is based on the time of the previous exam (either the passing time of Subject 1 or the failing time of Subject 2), and the same applies to Subject 3; 4. If someone schedules the next subject exam long after completing the previous one, their ranking during scheduling will be higher, pushing your ranking down. Conversely, if you schedule the next subject exam immediately after completing the previous one, your ranking will be lower.
14
4
Share

What to Do When the Roewe RX5 Battery Dies?

Roewe RX5 battery dead solution: Use jumper cables to charge. Before connecting the jumper cables, be sure to turn off the engine. When connecting to the power supply vehicle, ensure that the positive and negative terminals of the jumper cables do not touch each other. When removing the jumper cables, disconnect the negative terminal first, then the positive terminal. Below is some relevant information about the Roewe RX5: 1. The Roewe RX5 is an internet-connected SUV, featuring Porsche-tuned chassis, GKN intelligent all-wheel drive system (same as Land Rover), full independent suspension system, and four-way high-speed CANBUS system bus, all of which enhance the driving and riding experience. 2. The new Roewe RX5 is equipped with the upgraded Internet Car Intelligent System 2.0. Its exterior adopts the "Rhythm Design" language, featuring matrix LED headlights composed of 24 LED light sources. The body lines are stylish and dynamic, with a dual-waistline design on the side, giving the vehicle a rhythmic and tension-filled appearance.
17
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.