What to Do When Foreign Objects Get Stuck in the Window Glass Gap?

2 Answers
OBrantley
07/24/25 6:28am
Foreign objects stuck in the window glass gap can be blown out using an air gun. Below are the impacts of having foreign objects in the window: 1. Falling into the window gap can affect the drainage channel inside the door: At best, it may cause the inner door skin to mold; at worst, it can damage the motor of the window regulator and even affect the central door lock. 2. Blocking the drainage hole: It can clog the door drainage hole, leading to poor drainage or direct water leakage, which may result in mold and unpleasant odors. Water inside the door may also cause rust on the door panel and regulator. The window glass seal is not very tight, so rainwater can flow into the door through the gap between the seal and the glass during rain. There is a small hole at the bottom of the door designed to drain the incoming water.
Was this review help?
10
5
Share
AuroraFitz
08/11/25 2:15am
Never mess around when something gets stuck in your car window gap. I've encountered this issue several times myself, usually with small stones or leaves stuck in the track. If the window doesn't move smoothly, it can be troublesome. First, turn off the power and avoid forcing the window button—damaging the motor would be a huge loss. Use a flashlight to check the gap and locate the foreign object. If visible, gently remove it with small tweezers or a toothpick. If it won't budge, spray some WD-40 or silicone-based lubricant to loosen it, then slowly roll down the window to try dislodging it. For prevention, regularly clean the door edges and avoid leaving large window gaps when parked, especially in dusty areas. If you can't fix it, take your car to a professional shop immediately to check for track deformation or damaged seals. Remember, safety first—don't hesitate to seek help.
Was this review help?
5
2
Share
Expand All
More Forum Discussions

How Much Do Tires Affect Fuel Consumption?

Tires affect fuel consumption in the following ways: 1. The impact of tire width on fuel consumption: Wider tires have a larger contact area with the ground, resulting in greater friction resistance, which naturally leads to higher fuel consumption. Narrower tires, on the other hand, result in lower fuel consumption, a factor largely determined by inherent design. 2. The influence of tire tread patterns on fuel consumption: Off-road tires with larger tread patterns are suitable for rough terrains like gravel but consume the most fuel. Performance tires, which generally emphasize grip, have wider treads and offer better handling, resulting in moderate fuel consumption. Comfort tires, with their fine and smooth tread patterns, provide the lowest fuel consumption. 3. The effect of toe and camber angles on fuel consumption: Poor wheel alignment (incorrect toe or camber angles) increases friction between the tires and the ground, not only damaging the tires but also raising fuel consumption. 4. The role of tire pressure in fuel consumption: Insufficient tire pressure increases the tire's contact area with the ground, leading to higher friction. This not only causes wear on the tire shoulders but also increases fuel consumption.
10
1
Share

How to set up automatic locking for Volkswagen Magotan?

Magotan automatic locking setup method is as follows: 1. Set in the central control screen car menu, where the automatic locking function is available. 2. Find the "Auto Lock" option and tick it, so that the doors will automatically lock while driving. Here are some related information: 1. The purpose of the automatic locking function is anti-theft. It allows the doors to lock quickly after starting to drive, preventing door-pull robberies during traffic jams or at red lights, providing a certain level of security. Its advantage is that it protects child passengers inside the car, preventing young children from opening the door handles while the car is in motion. 2. The driving automatic locking is also called speed-sensitive automatic locking: it is an electronic device that automatically presses the lock button on the door when the vehicle speed reaches the value set by the computer, preventing accidental door opening. That is, when the speed reaches a set value, the car locks automatically. The set value is generally determined by the manufacturer, mostly between 10-20km/h.
8
4
Share

Can I Use Tap Water for Car Wiper Fluid?

Car wiper fluid should not be filled with tap water. Below are the reasons why tap water is unsuitable for car wiper fluid and the correct method for refilling: 1. Tap water contains many impurities that can easily clog the wiper nozzles. Additionally, tap water lacks cleaning properties and cannot effectively remove common windshield contaminants such as insect residue, bird droppings, or grease. Wiper fluid, on the other hand, can quickly eliminate stubborn stains, oil marks, and rain residue from the windshield while forming a protective layer to prevent dust and grease buildup. This ensures smoother and quieter wiper operation, keeping the windshield clean and comfortable while maintaining clear driving visibility. It also gently protects the wiper blades. 2. To refill the wiper fluid, first open the engine hood by pulling the support rod upward, then use the rod to prop it open. Locate the wiper fluid filler inlet under the hood, which is usually marked with a corresponding symbol. Once identified, pour the wiper fluid into the designated filler opening.
17
1
Share

What to Do When the Ford Escape Battery Dies?

If the battery of a Ford Escape dies, the only solution is to jump-start it using another car's battery. Connect the positive terminal of the dead battery to the positive terminal of the working battery, and then connect the negative terminals in the same manner. Here is some relevant information: 1. In case of a sudden battery failure, contact a rescue vehicle to connect jumper cables for temporary charging to start the engine. To avoid being unable to charge when the battery dies, it's advisable to keep a set of jumper cables in the car. 2. When connecting jumper cables, it's crucial not to reverse the connection order: first connect the positive terminal of the dead battery to the positive terminal of the rescue vehicle's battery, then connect the negative terminal of the rescue vehicle's battery to a metal part in the engine compartment of the dead vehicle (grounding). 3. After connecting the jumper cables, start the engine of the rescue vehicle and slightly increase the engine speed. After about 5 minutes, the dead battery should receive enough emergency charge. Once charging is complete, disconnect the jumper cables in the reverse order of connection.
17
1
Share

How many cylinders does the XC40 engine have?

The Volvo XC40 is equipped with two types of engines: three-cylinder and four-cylinder. The XC40 utilizes a total of three engines: a 1.5-liter turbocharged three-cylinder engine, a low-power version of the 2.0-liter turbocharged four-cylinder engine, and a high-power version of the 2.0-liter turbocharged four-cylinder engine. Below are some details about these engines: 1. The 1.5-liter turbocharged engine has a maximum power output of 120 kW and a maximum torque of 265 Nm, with peak torque available between 1,500 and 3,000 rpm. 2. The low-power 2.0-liter turbocharged engine delivers a maximum power of 140 kW and a maximum torque of 300 Nm, achieving peak torque between 1,400 and 4,000 rpm. 3. The high-power 2.0-liter turbocharged engine produces a maximum power of 185 kW and a maximum torque of 350 Nm, with peak torque available between 1,800 and 4,800 rpm. 4. The Volvo XC40's body dimensions are 4,425 mm in length, 1,863 mm in width, and 1,652 mm in height, with a wheelbase of 2,702 mm.
7
1
Share

Why does the Audi A6 engine make a ticking sound?

The reasons for abnormal noise in the Audi A6 engine may include the following aspects: 1. Valve noise: After starting the engine, there is a "ticking" sound, which is the sound of the valves, especially when the engine is cold. This is because the oil pressure has not yet built up, and the valves are not properly lubricated. It will naturally improve after a while. This situation often occurs if the car has been parked for a long time. 2. Insufficient lubrication: Generally, during a cold start, the engine sound may be slightly louder than when the engine is warm. As long as the sound is uniform and smooth, not harsh, it is usually not a problem. This is because, when the engine is cold, the gap between the cylinder wall and the piston has not yet reached the optimal size, and the lubrication from the oil is not sufficient. Normally, when the engine block temperature reaches about 95 degrees, the sound will return to normal. 3. Oil-related issues: Poor-quality oil, not changing the oil for a long time, or insufficient oil can easily increase friction between the valves and guides, as well as in hydraulic lifters, making various sounds in the engine louder.
18
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.