What to Do When Entering an Unmanned Parking Lot with Temporary License Plates?

1 Answers
DeEsther
07/29/25 7:11pm
Temporary license plates can enter unmanned parking lots. Here are the relevant details: 1. The parking lot's charging system will automatically recognize the plates, so there's no need to worry about whether you can enter the parking lot. With the continuous development of production technology, unmanned parking charging systems have gradually improved, enabling parking lot management without attendants. Generally, this method is referred to as an intelligent parking management system. 2. The intelligent parking management system mainly recognizes vehicles through their license plates and starts charging upon identification. For cars without installed license plates, entry can be achieved by scanning a QR code with a mobile phone, making the unmanned management system very comprehensive. 3. When exiting the parking lot, payment can be made manually or through self-service. The license plate recognition device automatically identifies the plate and calculates the vehicle's parking duration to determine the fee. If the parking lot fails to recognize the plate normally, you can seek assistance from staff, as some intelligent parking lots have security or staff members. It's important to note that whether a car uses temporary or official license plates, traffic rules must be followed while driving, and good car usage habits should be maintained.
Was this review help?
4
2
Share
More Forum Discussions

Do I Need to Replace a Tire with a Nail Puncture?

Tire punctured by a nail: If the nail punctures the sidewall, replacement is necessary; if it punctures the tread, only repair is needed, not replacement. Whether to replace the tire depends on the location and extent of the damage. If the nail punctures the tread and isn't too thick, it can be repaired at a professional repair shop. Conditions requiring tire replacement include: puncture hole diameter in the tread exceeding 6mm; sidewall puncture; deformation of the bead or tread; corrosion of the tire; damage caused by driving underinflated. Tire repair methods include: plugging, sealant injection, cold patch, hot patch, and mushroom plug. Plugging is the most common method, involving inserting a special rubber strip into the puncture. This method is quick and convenient, taking only minutes, and doesn't require removing the tire from the rim. Tire sealant is a white foam-like liquid, a synthetic polymer compound stored in a compressed canister. When used, it's injected through the valve stem, simultaneously sealing and inflating the tire. Under the centrifugal force of driving, the sealant evenly coats the inner tire surface, forming a sealing film that repairs the puncture. Cold patching requires removing the tire from the rim, locating the puncture, cleaning the area, and applying a special patch from the inside. Hot patching is similar but includes an additional step of heating the patch with a curing machine until it melts and bonds with the puncture. The mushroom plug uses a mushroom-shaped rubber patch inserted from inside the tire, with the stem pulled through the puncture, trimmed on the outside, and secured with adhesive on the inside.
7
1
Share

Where is the appropriate place to apply for ETC?

ETC can be processed at bank branches, highway service areas, and other institutions. To apply, you need to provide the original and photocopies of the vehicle owner's valid ID card and vehicle registration certificate. If the application is not made by the owner, the agent's valid ID card must also be provided. The photocopy of the vehicle registration certificate should include the page stamped with the most recent annual inspection seal. Additionally, a credit card application form is required; this credit card will be used to bind the ETC card. After obtaining the credit card, you can swipe it twice and use the POS receipt to collect and install the ETC onboard device for free at designated postal outlets, with no charges incurred during the process. Applicants must be between 18 and 60 years old and own a vehicle registered under their name. ETC stands for Electronic Toll Collection, meaning electronic toll system. Below are the precautions for installing ETC: Do not obstruct the driver's view; it is best to install it behind the rearview mirror: Many car models have a steeply angled windshield, which can reduce the driver's field of vision. If this is not considered during ETC installation, it may increase the driver's blind spots. Install it on the right side behind the rearview mirror to avoid obstructing the view. Do not interfere with charging: The ETC electronic tag consumes power but generally does not require charging or battery replacement, as it has a solar panel on the back for self-charging. Therefore, during installation, avoid the blacked-out areas on the windshield and positions that might block the solar panel. Once installed, do not remove it arbitrarily: The button in the middle of the adhesive is an anti-tamper lever connected to a switch. After installation, the windshield will press this lever in. If the tag is removed arbitrarily, the lever will pop out and trigger the switch, locking the electronic tag and rendering it unusable. You will then need to visit an ETC service point to unlock it. This mechanism is designed to prevent multiple vehicles from sharing one device. When using ETC, note the following: The ETC transaction sensing range is 8 meters. To avoid paying for the vehicle in front due to its faulty ETC device, maintain a distance of at least 10 meters from the vehicle ahead. The ETC lane recognizes vehicles at a speed of 20 km/h; driving too fast may result in failure to read the vehicle's device information, leading to failed toll deductions. When using a debit card to bind ETC, insufficient balance may also cause toll deduction failures.
15
3
Share

What is the Difference Between Turbocharged and Naturally Aspirated Engines?

Turbocharged and naturally aspirated engines differ in the following aspects: 1. Different working principles: Turbocharged engines utilize exhaust gases to drive the turbine, increasing the engine's air intake to generate power; naturally aspirated engines obtain power through repeated intake and combustion cycles in the cylinders. 2. Different power delivery speeds: Turbocharged engines benefit from the intervention of the turbocharging system, providing faster power delivery; naturally aspirated engines deliver power more slowly. 3. Different noise levels: Turbocharged engines start up quickly, resulting in louder noise; naturally aspirated engines offer quieter and smoother idling, with less noise during startup.
10
0
Share

How Often Should the Gear Oil Be Changed for a Sail?

The gear oil for a Sail is recommended to be changed every 18 months or 30,000 kilometers. Gear oil primarily refers to the lubricant for the transmission and rear axle, differing from engine oil in terms of usage conditions, composition, and performance characteristics. The main functions of gear oil include lubricating gears and bearings, preventing wear and corrosion, and assisting in heat dissipation for the gears. The Sail's body dimensions are 4,249 mm in length, 1,690 mm in width, and 1,503 mm in height, with a wheelbase of 2,465 mm. The Sail features front-wheel drive, a MacPherson strut front suspension, a torsion beam rear suspension, and a unibody construction.
5
1
Share

What are the reasons for BYD DMi-EV limitation?

BYD DMi-EV limitation refers to the occasional dashboard alert of EV function limitation during driving, where the engine starts, and the system can resume normal operation after turning off and restarting the power, with the fault occurring irregularly. The following are the reasons for DMi-EV limitation: 1. Battery pack failure. 2. BMS failure. 3. Drive motor controller failure. 4. Related circuit failure. Here is a brief introduction about BYD Auto: BYD Auto, generally referring to BYD Company Limited, is headquartered in Shenzhen, Guangdong, China. It is a new technology private enterprise with three major industrial groups: IT, automobiles, and new energy.
17
1
Share

What causes the clunking sound when the car starts moving?

The clunking sound when the car starts moving is caused by friction between the brake pads and brake discs, which is normal and nothing for the owner to worry about. The vehicle's braking system consists of the master cylinder, vacuum booster, wheel cylinder, brake pads, and brake discs. When the brake pedal is pressed, the brake pads clamp onto the brake discs, converting kinetic energy into heat energy to slow down the car. The vacuum booster provides assistance when the brake pedal is pressed, making it easier for the driver to apply the brakes. Upon opening the engine hood, a black metal disc can be seen below the windshield on the driver's side - this is the vacuum booster. In front of the vacuum booster is the master cylinder, which has a reservoir for holding brake fluid.
20
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.