What to Do When Car Lights Won't Turn Off?

1 Answers
MacHazel
07/29/25 4:57pm
If the car lights won't turn off, you can first remove the light fuse or the light connector to prevent the lights from draining the car battery, and then go to a repair shop to have professional technicians inspect the light wiring. Here is an extended introduction: 1. There are many reasons why car lights won't turn off, such as damage to the light combination switch, sticking of the headlight relay, short circuit in the light wiring, or damage to the headlight control module. 2. In more cases, light malfunctions are not just minor issues like a burnt-out bulb, corroded socket, or damaged plug, and often require professional diagnostic techniques to analyze the root cause of the problem.
Was this review help?
20
0
Share
More Forum Discussions

What Causes Shaking When Starting in 1st Gear with a Manual Transmission?

Manual transmission starting shaking reasons: When starting with a manual transmission, the clutch is in a semi-engaged state, which can cause a certain degree of slight shaking; if starting on a slight slope without giving gas, the shaking can be more noticeable. This situation is caused by the clutch part; if the shaking is severe, the first possible issue could be a fault in the clutch components. Solutions for shaking not caused by operation: When starting, always gently press the accelerator while releasing the clutch based on feel. With practice, starting can be done without shaking. If the issue is not due to operation, the possible cause might be insufficient engine power. If the engine power cannot keep up when starting, the car will shake. (Check the engine). Loose connection between the transmission and the chassis. Starting can also cause a shaking sensation. (Check chassis components such as the half-shaft, CV joint, etc.). Uneven engagement between the clutch pressure plate and the clutch friction disc. Starting will cause shaking. This could be due to uneven pressure from the clutch pressure plate fingers. The only solution is replacement.
2
4
Share

How Many Days After Car Polishing Should You Avoid Washing the Car?

You should avoid washing the car for three to seven days after polishing. The material used in car polishing is glaze, which requires time to solidify and harden. Washing the car immediately can damage the glaze layer on the paint surface, resulting in less effective paint protection. Advantages of car polishing: It can make the car paint smoother and shinier. For oxidized, dull, or scratched paint surfaces, polishing can remove oxides and corrosive substances, restoring the paint's cleanliness. After waxing, it can provide waterproofing, anti-static properties, UV protection, and a glossy finish. Precautions for car polishing: Control the speed of the polishing machine and do not exceed the selected speed range. Maintain consistent polishing direction and follow a certain order. When polishing the hood, cover the windshield with a large towel or masking film to prevent polishing wax from sticking to the glass seals and wipers, which can be difficult to remove. Apply polishing wax evenly on a wool pad or sponge pad to prevent splashing and material waste. The polishing wax can first be poured onto the paint surface and spread evenly to prevent splashing.
9
2
Share

How many colors are available for the Senova D50?

The Senova D50 offers a total of seven exterior color options. Here are the specific color choices: In addition to common colors like Obsidian Black, Platinum Gray, Polar Silver, and Pearl White, consumers can also opt for more vibrant shades such as Lava Red, Amber Gold, and Ice Crystal Blue. Below is additional information about the Senova D50: 1. Engine: (1) 1.5L naturally aspirated engine. The 1.5L naturally aspirated engine delivers 116 horsepower and a maximum torque of 148 Nm. This engine features multi-point fuel injection technology and uses an aluminum alloy cylinder head and block. (2) 1.5L turbocharged engine. The 1.5L turbocharged engine produces 150 horsepower and a maximum torque of 210 Nm. This engine also features multi-point fuel injection technology and uses an aluminum alloy cylinder head and block. 2. Transmission: (1) The 1.5L naturally aspirated engine is paired with either a 5-speed manual transmission or a CVT. (2) The 1.5L turbocharged engine is paired with either a 6-speed manual transmission or a CVT. 3. Suspension: (1) The front suspension uses a MacPherson independent suspension. (2) The rear suspension uses an H-type torsion beam non-independent suspension.
7
2
Share

Does Water in the Car Trunk Affect the Vehicle?

Water in the car trunk does affect the vehicle. It can easily cause rust in the trunk, and in severe cases, perforation may occur. Preventive Measures for Water in the Car Trunk: Regularly clean the sealing strips. The waterproofing of various parts of the car body is ensured by sealing strips, which are made of rubber material. These strips have a certain degree of strength and hardness and do not deform under certain pressure conditions. However, long-term exposure to air will inevitably lead to natural aging, and frequent use can also cause wear and tear, making the sealing strips highly susceptible to damage. Check if the trunk has deformed. The design of the car trunk follows certain rules, with corresponding drainage arc designs in the A, B, C, and D zones. If the shape of the trunk is compromised, it can lead to severe water leakage during rain. Solutions for Water in the Car Trunk: Drain the water as soon as possible. There is a rubber drainage plug at the bottom of the spare tire compartment in the trunk; removing it will allow the water to drain. Quickly identify the source of the water ingress and check if the trunk lid is deformed or if the surrounding rubber seals are damaged. Ventilate the trunk by opening the lid. Remove the trunk floor panel and internal items, then leave the lid open to air for an hour to prevent mold and rust.
8
0
Share

How to Compensate When a Motor Vehicle Collides with an Over-standard Electric Vehicle?

Specific compensation depends on the accident scene conditions and the accident liability certificate issued by the traffic police. There is no necessary connection with whether the electric vehicle exceeds standards or is classified as a motor vehicle. If the motor vehicle is deemed at fault, the liability proportion cannot be reduced on the grounds that the other party is a non-motor vehicle during civil compensation. Motor vehicle accident liability division: 1. Accident liability proportion: If a traffic accident occurs between motor vehicles, the party at fault shall bear the compensation liability. If both parties are at fault, the liability shall be shared according to their respective fault proportions: primarily at fault, 70%; equally at fault, 50%; secondarily at fault, 30%. 2. Motor vehicle liability proportion: If a traffic accident occurs between a motor vehicle and a non-motor vehicle, or between a motor vehicle and a pedestrian, the motor vehicle party shall bear the liability for the part exceeding the liability limit. However, if there is evidence that the non-motor vehicle driver or pedestrian violated traffic safety laws and regulations, and the motor vehicle driver has taken necessary measures, the liability shall be adjusted accordingly: motor vehicle primarily at fault, 80%; motor vehicle equally at fault, 60%; motor vehicle secondarily at fault, 40%; motor vehicle not at fault, 10%.
14
5
Share

Will the paint chip on a car get bigger if left unrepaired?

If the paint chip on a car is left unrepaired, the damaged area will indeed get larger. The car's paint surface naturally oxidizes over time, causing the paint film thickness to decrease until the underlying material is exposed. Causes of car paint chipping: Scratches or collisions; Issues during the painting process due to poor quality. This includes low spraying temperature, expired paint, excessive dust on the car surface, overly thick paint application, poor-quality primer, poor-quality putty, or inferior car body quality. Methods for repairing car paint: First, clean the area to be repaired with water. Use coarse sandpaper to smooth out any rough edges from the scratch, then use fine sandpaper to polish until smooth. After sanding, dry the area with a clean towel or paper towel. Apply an appropriate amount of putty to a spreader based on the size of the dent and fill the dent. For repairing dents on the bumper, first smooth out any rough edges. After sanding and cleaning, apply the putty. Even with regular maintenance or touch-ups, prolonged use of a car will inevitably lead to paint wear and aging. To restore the car's original glossy appearance, a full-body repaint is necessary.
14
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.