What to Do When Car Horn Bass Produces Buzzing Resonance?

2 Answers
VonZane
07/28/25 11:50pm
First, reset all additional functions of the car audio system to factory settings, and center the high, mid, and low tones as well as the left-right balance. Below is an introduction to air horns: 1. Concept: An air horn is a type of car horn, categorized into electric air horns and mechanical air horns. Air horns use compressed air flow to vibrate a metal diaphragm, typically shaped like a long horn (cylindrical), producing loud, high-pitched sounds that travel far. 2. Maintenance: Clean surface dirt during maintenance; replace the diaphragm if rust or damage is found upon disassembly. When washing the vehicle, avoid directing water into the horn casing to prevent affecting its sound. The QL11 type air horn requires an air pressure of 294~980 kPa for normal sound performance.
Was this review help?
4
5
Share
LeEvangeline
08/12/25 4:08am
I often encounter the issue of low-frequency buzzing and resonance from the car horn while driving, which makes me feel very uncomfortable, especially when honking at narrow intersections where it produces harsh echoes. I remember last time my car had the same problem, and after inspection, it was found that the horn mounting screws were loose. Tightening them with a wrench resolved the resonance. If the buzzing persists after securing the screws, it might be due to an aging or damaged horn unit, and replacing it with a new universal horn costing just a few dozen dollars should do the trick. Additionally, check if the wiring connections are secure, as broken wires or poor contact can cause abnormal noises. If there’s a resonance point in the car body, adding a rubber vibration-damping pad to isolate the horn position can also help prevent the issue. Don’t overlook the safety risks—buzzing can affect auditory judgment, so timely action is better than delaying. Also, avoid exposing the horn to water or dust when parking to extend its lifespan.
Was this review help?
11
5
Share
Expand All
More Forum Discussions

Which year is the Haojue Yinbao 123-7 model from?

It was likely produced between 2003-2007. Here's some relevant information: Haojue Motorcycles: Haojue motorcycles are highly popular both domestically and internationally, with sales and service shops covering almost every city, county, and major township across China. Wherever you travel across China - from bustling streets to rural roads, even in farmland areas - Haojue users can be seen everywhere. Introduction: Haojue is a Chinese famous brand and well-known trademark, offering over ten product series with more than a hundred models. Its classic model series - the Diamond Leopard - has maintained its position as China's top motorcycle brand for many years. The company owns many renowned sub-brands, including: Diamond Leopard, Lishuang, Disuang, EN Ruishuang, Yueguan, GN Prince, Yinbao, KA Tianlongxing, Neptune, Fuxing, Yuexing, Tianying, Tianyu, Xiyun, Yuzuan, Red Treasure, as well as the high-performance sports bike GW250 Lichi, all enjoying excellent reputation.
2
3
Share

What Impact Does Replacing the Cylinder Head Gasket Have on a Ford Escape?

Replacing the cylinder head gasket on a Ford Escape can lead to a certain degree of depreciation in the vehicle's value. Below is more information about cylinder head gaskets: 1. Reasons: Because replacing the cylinder head gasket requires disassembling most of the engine components, it is difficult to restore the cylinder head and most electronic devices to their original factory condition after disassembly. If the replacement and repair process is not strictly carried out according to technical requirements, it may leave hidden dangers for other components, thereby affecting the vehicle's value. 2. Introduction: The cylinder head gasket is a sealing gasket installed between the cylinder head and the cylinder block. It is connected to the cylinder block via cylinder head bolts to ensure the sealing of the cylinder, preventing the leakage of high-temperature and high-pressure gases, coolant, and lubricating oil. It must tightly seal the high-temperature and high-pressure gases generated inside the cylinder and the coolant and oil with certain pressure and flow rate passing through the gasket, while also withstanding the corrosion and impact of water, gas, and oil. Common gasket burnouts are caused by high-temperature and high-pressure gases impacting the gasket, leading to cylinder gas leakage and the mixing of lubricating oil and coolant.
18
5
Share

What spark plugs are used in the Elantra?

The spark plug model for the Elantra is RC10YC4. If you prefer platinum spark plugs, you can choose NGK6809 or NGK5787. Under normal maintenance conditions, car spark plugs should be replaced after driving 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine, so it is recommended to follow the user manual. You can refer to the following standards for maintenance and replacement: platinum spark plugs should be replaced at 40,000 kilometers, ordinary nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers. Steps for replacing spark plugs: Open the hood, lift the engine's plastic cover, and remove the high-voltage distributor wires. Mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for any external debris like leaves or dust and ensure they are cleaned thoroughly. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the high-voltage distributor wires according to the firing order and secure the cover.
19
0
Share

How to Turn Off the Auto Start-Stop Function in Audi A6?

Method to turn it off: The start-stop system button can be found either on the vehicle's center console or in the button area behind the gear lever. The function is enabled by default when the vehicle leaves the factory, indicated by the "yellow light not lit." Pressing this button to make the "yellow light lit" cancels the start-stop function (OFF means "closed"). You can also ask the car manufacturer to set this function to be turned off by default. Below is an introduction to the start-stop system: 1. Auto Start: When it's time to move forward again, the auto start system automatically restarts the engine. The STT intelligent fuel-saving system is a system that controls the engine's start and stop. The working principle of the start-stop system is that when the vehicle stops moving due to congestion or at an intersection. 2. Press the Brake Pedal: The engine idles without being in gear, the wheel speed sensor of the anti-lock system shows zero, and the electronic battery sensor indicates there's enough energy for the next start. After these three conditions are met, the engine automatically stops. When the traffic light turns green, the driver presses the clutch.
1
0
Share

Can I switch from C1 to C2 during the driving test?

During the process of obtaining a C1 license, candidates can change the type of driving test to C2. Changing the test vehicle type will not significantly alter the test content, only the test materials will be modified, as a C1 license allows driving all vehicle types under C2, C3, and C4. Permitted vehicle types for C1: The scope of a C1 license includes small and micro passenger vehicles, light and micro cargo vehicles; light, small, and micro special-purpose vehicles; and small passenger vehicles with a seating capacity of 9 or fewer people. Vehicles not permitted with a C1 license: large buses, tractors, city buses, medium-sized buses, large trucks, ordinary three-wheeled motorcycles, ordinary two-wheeled motorcycles, light motorcycles, wheeled self-propelled machinery, trolleybuses, and trams. Additionally, a C1 license does not permit driving vehicles with more than 9 seats or trucks exceeding 6 meters in total length. Age requirements for C1: There is no upper age limit for applying for a C1 license, with the minimum age being 18. Applicants aged 70 and above must pass tests assessing memory, judgment, and reaction abilities.
5
2
Share

Where is the fuel tank cap button of Kia K5?

The fuel tank cap switch of Kia K5 is located on the floor to the left of the driver's seat. To open the fuel tank cap, you must pull the fuel filler switch. The methods to open the fuel tank are as follows: Mechanical key opening: This is usually seen in some hardcore off-road vehicles. Nowadays, ordinary family cars generally do not use mechanical keys to open the fuel tank because it is relatively complicated to use. In-car switch method: The in-car fuel tank switch is located in different positions in different car models. Some are on the floor to the left of the driver's seat, some are on the left front door panel or the center console, all marked with a fuel pump icon. However, it should be noted that the in-car switch can easily make the owner forget to turn off the engine before refueling, so the owner should remember to turn off the engine before refueling. Press-type opening method: The press-type fuel tank door opening is currently the most convenient method. The owner only needs to park the car, and the fuel attendant can press to open it for refueling. However, when the car is not parked for refueling, the owner must remember to lock the central control, otherwise, the fuel tank cap can be opened.
20
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.