What to Do When a Car Rolls Over?

What to Pay Attention to When Inspecting a New Car

When inspecting a new car, pay attention to the following aspects: 1. Documentation Check: This includes the purchase invoice, vehicle certificate, warranty service card, vehicle user manual, factory certificate/vehicle factory inspection sheet. Some vehicles may have a separate engine user manual and spare keys. Certain optional equipment may have specific requirements or regulations, so consumers should request relevant documentation from the dealer. 2. Exterior Detail Inspection: Some comprehensive dealers may sell test drive cars, inventory cars, or accident-damaged cars as new vehicles to consumers, concealing the vehicle's origin by offering seemingly attractive discounts. In reality, these could be unwanted accident-damaged cars. Some dealers may also take advantage of consumers' unfamiliarity with models by selling base models as high-end models to increase profits. Therefore, consumers must inspect the vehicle carefully. Details include: (1) Carefully check if the paint color is consistent across the entire vehicle. Look for scratches, peeling, cracks, bubbles, or rust on the body surface. Feel for any repair marks with your hands. If you notice any part where the paint color or thickness doesn’t match the surrounding areas or shows subtle circular scratch marks, it may indicate prior damage that has been repainted. (2) Examine the engine hood and roof at a 45-degree angle, as the paint quality on these horizontal surfaces best reflects the spray painting process and is most likely to reveal flaws. Poor application of any paint layer can easily result in wrinkles or bubbles. (3) Check the tire brand against the parameter sheet to ensure consistency, and look for obvious friction marks on the tire surface and tread hairs. (4) New cars are allowed a certain mileage from the factory, generally within 100km is considered normal.

13

4

Share

How to adjust the time on the new Buick GL8?

Steps to adjust the time on the new Buick GL8: 1. Turn on the radio power and locate the "RPT" button on the panel. 2. Press and hold for 3 seconds. When the screen display starts blinking, rotate the knob on the right to adjust the hour. 3. Then press the center button of the right knob to select and adjust the minutes. Turn off the radio, and the time will be set correctly. Additional information about the GL8: 1. As a top-tier MPV model, it has achieved batch exports with its luxurious style, powerful performance, and spacious comfort, being praised by Southeast Asian media as the "perfect MPV." 2. It has also served as the official VIP vehicle for major international events such as the Beijing Olympic bid and APEC meetings, with notable figures like Bill Gates, Yo-Yo Ma, and Luciano Pavarotti having been its passengers.

18

0

Share

How to Turn Off the Headlights on a Sylphy?

The Sylphy's steering wheel has a light control knob on the right side. Simply rotate the knob to the 'off' or 'on' position to turn the headlights off or on. Here is some relevant information: 1. Automotive lights are various traffic lights installed on vehicles to ensure safe driving, categorized into illumination lights and signal lights. The primary purpose of headlights is to illuminate the road and objects ahead, ensuring driving safety. They can also use high and low beam alternation as a signal for overtaking at night. 2. Fog lights are used in low visibility conditions such as fog, snow, heavy rain, or dust, serving as road illumination and providing signals to oncoming vehicles. These lights are often yellow because yellow light has a longer wavelength, offering better fog penetration. 3. Reverse lights are used to illuminate the road behind the vehicle and to inform other vehicles and pedestrians that the vehicle is reversing or preparing to reverse. They function as light signal devices and emit white light.

4

1

Share

How to Repair a Dented Car Exterior?

Solutions for a dented car exterior: 1. The car's exterior is made of a combination of metal sheets and plastic. The front and rear bumpers are usually plastic. Plastic softens when heated, so based on this principle, the dented area can be heated and pushed out. 2. First, boil a large bucket of hot water, then pour the hot water over the dented area using a ladle to heat it. 3. The heating process with hot water is quite lengthy. It takes time for the dented plastic to soften sufficiently to achieve the desired effect. 4. Once the plastic has softened to the right degree, push it out from the inside of the engine hood with your hand until the dented area pops back into place. 5. If it still feels too hard to push out, it means the heating is not sufficient yet, and more hot water is needed to continue the heating process.

12

5

Share

How to Connect Jumper Cables for a Car?

When a car battery is dead, it will definitely affect the entire vehicle's power supply system, and even the engine cannot be started. In this case, a jump start is needed to start the engine. Detailed steps for connecting jumper cables: 1. First, ensure that the auxiliary battery is 12V and the negative terminal is already grounded. Of course, all unnecessary lights and accessories should be turned off to avoid electrical accidents. 2. Then, connect the jumper cables in the correct order. Never reverse the positive and negative terminals of the cables, as sparks may occur when connecting. Also, ensure the cables are tightly wrapped around the battery terminals (for full contact) to prevent sparking during the process. 3. Start the engine of the vehicle with the auxiliary battery and let it run at medium speed. Then, start the engine of the vehicle with the depleted battery. 4. Finally, disconnect the cables in the exact reverse order.

9

0

Share

What to Do When a Wrench Symbol Appears on the Dashboard?

The method to eliminate the wrench symbol appearing on the car dashboard is as follows: 1. Turn off the engine, press and hold the short-distance counter reset button below the tachometer. 2. Turn the ignition switch to the ON position, then release the reset button. 3. Pull out the minute button on the clock, turn the minute button to the right, and the mileage display will appear on the screen. 4. Turn off the engine to reset the reminder message. 5. Turn the ignition switch to the ON position. Information about the wrench symbol on the car dashboard is as follows: 1. The appearance of a wrench on the dashboard is a maintenance reminder symbol, indicating that the vehicle needs servicing. 2. After maintenance is completed, the service staff at the 4S store can reset the maintenance mileage to zero through the setup program.

7

0

Share

What to Do When a Car Rolls Over?

What to Pay Attention to When Inspecting a New Car

How to adjust the time on the new Buick GL8?

How to Turn Off the Headlights on a Sylphy?

How to Repair a Dented Car Exterior?

How to Connect Jumper Cables for a Car?

What to Do When a Wrench Symbol Appears on the Dashboard?

What does 'services' mean in a car?

How to reset the tire pressure warning light on Audi A3?

Which country is Mazda from?

Is Car Rain Repellent Useful?