What to Do When a 2010 Teana Suddenly Fails to Start?

1 Answers
AndresLee
07/30/25 3:38am
Check the ECM fuse, which is the main power line for the engine control unit, to ensure it is functioning properly. If not, replace it. Inspect the IPDM control unit, also known as the intelligent control unit. If the wiring harness connector of the IPDM control unit has poor contact, it will affect the aforementioned functions.
Was this review help?
3
2
Share
More Forum Discussions

Where should WD40 not be sprayed?

WD40 should not be sprayed on rubber, plastic, or wax areas of a car. WD40, known as a moisture-displacing and rust-preventing lubricant, has penetrating properties that can thoroughly remove oil stains, dirt, dust, and other residues adhering to metal surfaces, without damaging materials like paint, fiber, plastic, or nylon on metal surfaces. The functions of WD40 include: 1. Completely removing stubborn stains adhered to metal surfaces; 2. Removing moisture and water, quickly drying electronic systems to prevent short circuits caused by humidity; 3. Removing rust that binds metals, freeing stuck, frozen, or rusted metal parts; 4. Containing anti-corrosion components to protect metal surfaces from moisture and other corrosive factors.
14
2
Share

What is the voltage range of an oxygen sensor?

Oxygen sensor voltage ranges between 0.1V to 0.9V, with an average value between 0.4V to 0.5V. The faster the voltage frequency changes, the better the sensor performance. If the voltage remains at 0V or 1V without variation, it indicates significant aging of the oxygen sensor, requiring prompt replacement. The automotive oxygen sensor serves as a crucial feedback component in electronically fuel-injected engine control systems, playing a key role in regulating vehicle emissions, reducing environmental pollution, and improving fuel combustion efficiency. Vehicles are equipped with both upstream (front) and downstream (rear) oxygen sensors, which function synergistically.
2
4
Share

What is the normal data range for ignition advance angle?

The normal range for ignition advance angle is between 6 to 12 degrees. The ignition advance angle refers to the crankshaft rotation angle from the moment the spark plug fires (before the engine piston reaches the compression top dead center) until the piston actually reaches the compression top dead center. The ignition advance angle system consists of three components: microcomputer, various sensors, and ignition actuator. Factors affecting engine ignition advance angle include: 1. Engine speed; 2. Load; 3. Octane number; 4. Combustion chamber shape; 5. Combustion chamber temperature; 6. Air-fuel ratio; 7. Atmospheric pressure; 8. Coolant temperature.
11
4
Share

How Long Is the Warranty for a Car Steering Gear?

Car steering gears are typically covered by a three-year warranty. Below is some information about the warranty for car steering gears: 1. Steering Gear: The warranty period for the steering gear is generally the same as the vehicle's overall warranty, but this may vary depending on the brand and model. The steering gear, also known as the steering box, is a crucial component in a car's steering system. All vehicles are equipped with power steering systems. 2. Electric Power Steering: Electric power steering systems do not have hydraulic mechanisms. These systems do not require power steering fluid or a power steering pump, as they rely directly on an electric motor to provide steering assistance.
4
1
Share

Why Does Engine Sludge Occur?

Engine sludge occurs due to the following reasons: Blow-by gases contain various unburned products, dust, and metal oxides that enter the crankcase and mix with engine oil. Through further oxidation and condensation, they form acidic insoluble substances in the lubricating oil, which then combine with other solids and moisture to eventually form sludge deposits throughout the engine. Methods for maintaining a car engine: 1. Regularly change engine oil and oil filter; 2. Use lubricating oil of appropriate quality grade; 3. Periodically clean the radiator; 4. Maintain the three filters; 5. Keep the crankcase ventilated; 6. Regularly clean the crankcase; 7. Periodically clean the fuel system.
10
3
Share

Which brand does Haval belong to?

Haval is a brand under Great Wall Motors, manufactured by Great Wall Motor Company Limited. Taking the 2021 Haval H6 as an example, its body dimensions are: length 4653mm, width 1886mm, height 1730mm, with a wheelbase of 2738mm and a fuel tank capacity of 58 liters. The 2021 Haval H6 is equipped with a 2.0T turbocharged engine, delivering a maximum power of 155kW and a maximum torque of 325Nm, paired with a 7-speed dual-clutch transmission. It features a front suspension type of MacPherson independent suspension and a rear suspension type of multi-link independent suspension.
19
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.