What to Do on Rainy Days Without Heated Rearview Mirrors?

What are the reasons for the ABS light in a Polo being on?

ABS light being on can indicate various conditions, with different causes and solutions for each state, as detailed below: State 1: ABS warning light remains constantly on (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS control unit from determining the vehicle speed and calculating the wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the dirt from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Poor signal due to loose connections in the system wiring or poor contact in the ABS relay, leading to system malfunction. Solution: Check the wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently turns on, but turns off during acceleration. Cause: When multiple electrical devices are in use, the battery voltage drops below 10.5V. As the engine speed increases and voltage rises, the ABS light turns off. This may also occur if the ABS system's power supply voltage is too low due to poor terminal contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light remains on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor wiring connection in the ABS hydraulic valve body; ABS control unit failure. Solution: Loosen the grounding screw of the hydraulic valve body, then retighten it, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR control unit. State 4: ABS warning light turns on during high-speed driving. Cause: During high-speed driving, the ABS control unit detects a significant discrepancy between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently turns on. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and use a finger to push the brake switch linkage all the way down, then release the brake pedal to complete the self-setting position; replace the brake light switch if necessary. If the ABS warning light is on, it is advisable not to continue driving. The illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's trajectory, posing significant safety risks.

20

5

Share

How to adjust the dashboard clock on an older BMW X3?

First, press the vehicle's one-touch start button to start the vehicle, then locate the SET button on the dashboard to begin adjusting the time. Press the one-touch start button to start the vehicle and power it on, then find the "Settings" button on the central display screen and click to enter the settings.

15

1

Share

How to Use the Remote Control to Roll Up and Down Windows on the Leopaard CS10?

First, test whether each window rolls up and down properly. Lower all the windows completely and hold down the window-down button for 5-10 seconds without releasing. Then, raise all the windows completely. Take out the key at a distance of 20-30 meters from the car. Simply press and hold the lock button on the car key continuously to operate the windows.

9

4

Share

How to deactivate the Mazda6 anti-theft system?

First, press the MODE button on the multifunction steering wheel while the vehicle is not powered on. Then, press the mute button on the vehicle to prevent the alarm from continuously sounding. Next, click the CANCEL button on the right side of the steering wheel to deactivate the vehicle's anti-theft system. After that, turn the vehicle key to start the engine.

5

0

Share

What to Do When the Leiling Car Key is Locked in the Trunk?

When the commonly used key is accidentally locked in the car, retrieving the spare key might be the simplest solution. If for various reasons you cannot get the spare key in time, calling the 4S store for assistance is also a good option. When neither retrieving the spare key nor seeking help from the 4S store is feasible, hiring a locksmith to unlock the car is another method.

17

4

Share

What to Do If You Accidentally Drive Against Traffic at an Intersection?

Traffic police on-site can issue a fine to individuals and make the penalty decision immediately. For off-site enforcement, traffic police will impose fines on the owner, manager, or driver of the offending vehicle based on traffic monitoring records. Violations handled through simplified procedures are subject to fines, and only those who have passed the training and examination conducted by the municipal public security traffic management department are qualified to handle them.

18

0

Share

What to Do on Rainy Days Without Heated Rearview Mirrors?

What are the reasons for the ABS light in a Polo being on?

How to adjust the dashboard clock on an older BMW X3?

How to Use the Remote Control to Roll Up and Down Windows on the Leopaard CS10?

How to deactivate the Mazda6 anti-theft system?

What to Do When the Leiling Car Key is Locked in the Trunk?

What to Do If You Accidentally Drive Against Traffic at an Intersection?

What is the Difference Between Blind Spot Monitoring and 360-Degree Surround View?

What is the reason why the booster pump makes noise intermittently when not in use?

How Many Kilometers Should a Car's Air Filter Be Replaced After Driving?

What is the Scrapping Period for General Vehicles?