What to Do If Your Vehicle Fails the Annual Exhaust Emission Test?

1 Answers
MayaMarie
07/29/25 11:04pm
Solutions for failing the annual vehicle exhaust emission test include: 1. Cleaning the three-way catalytic converter; 2. Cleaning the front oxygen sensor; 3. Using higher-quality gasoline; 4. Checking the engine's working condition; 5. Accelerating and driving several kilometers on the highway. Reasons for failing the annual exhaust emission test are: 1. Poor fuel quality; 2. Malfunction of the three-way catalytic converter or oxygen sensor; 3. Large spark plug electrode gap; 4. Overly rich or lean air-fuel mixture; 5. Poor gasoline atomization; 6. Abnormal engine operation; 7. Dirty intake system, exhaust system, or fuel system; 8. Vehicle aging.
Was this review help?
12
0
Share
More Forum Discussions

What Causes a Car to Stall During Normal Driving?

Here are the specific reasons why a car may stall during normal driving: 1. During normal engine operation, the fuel pump draws fuel from the tank, which passes through the filter into the distribution lines and is then sprayed by the injectors to form an air-fuel mixture. In this process, the fuel pump and injectors are prone to failure, followed by filter and fuel line blockages. Focus on inspecting these two areas. If necessary, clean the fuel lines. To reduce the occurrence of such issues, always refuel at reputable gas stations with the correct grade of gasoline and ensure timely refueling, avoiding letting the fuel level drop below the red line. 2. Throttle body blockage. Generally, mechanics will consider cleaning the throttle body. However, if frequent cleaning of the throttle body does not fully resolve the stalling issue, it is usually a sign of a fault. Also, check the vacuum pump to ensure normal air intake. 3. Abnormal spark plug ignition. Replace spark plugs according to their service life. In a gasoline engine, the combustible mixture is ignited by the spark plug near the top dead center of compression. Therefore, when a spark plug fails, it naturally causes the vehicle to stall. Typically, replacing the spark plug completely resolves the issue, but temporary fixes like cleaning the electrodes or adjusting the central electrode length can be used in emergencies. Additionally, insufficient battery voltage, leakage, faulty ignition coils, or wiring issues can lead to poor ignition or stalling. 4. Sensor failure causing ECU protective fuel cut-off. Check whether all sensors and actuators are functioning properly. Key sensors include the throttle position sensor, oxygen sensor, crankshaft position sensor, etc.
9
4
Share

How to Match the Volkswagen 01325 Fault?

To address the Volkswagen 01325 fault code, it is necessary to inspect and repair the tire pressure system and reset the tire pressure fault codes within the system. The specific steps are as follows: 1. Connect to the vehicle's OBD port, access the onboard computer system, and select the Volkswagen general system. 2. Click on system selection, then choose 03 brake system, followed by 04 system basic adjustment. Enter channel 042, click adjust, and the screen will display a completion message. 3. Finally, select to clear the fault code, and this fault code will disappear. The Volkswagen 01325 fault code indicates an issue with the vehicle's tire pressure monitor control unit. The dimensions of the Volkswagen Lavida are 4670mm in length, 1806mm in width, and 1474mm in height, with a wheelbase of 2688mm.
9
3
Share

Is It Safe If a Piece of Tire Rubber Is Torn Off?

Tire damage where a piece of rubber is torn off can be concerning. If the damage is on the sidewall of the tire, it is recommended to replace the tire, as the sidewall is the weakest part of the tire. If the fabric layers are exposed, it becomes particularly dangerous and significantly increases the risk of a blowout. For safety reasons, it is generally advisable to replace the tire with a new one. However, if the depth and width of the damage are less than 3 millimeters, the tire can still be used as a spare. More details are as follows: 1. Tire Damage: Any damage to a tire should be taken seriously, as tires bear the entire weight of the vehicle, and a blowout poses a significant risk. If a small piece of rubber is torn off from the tread pattern, it may not be a major issue for daily driving, but it is not recommended for highway use. If the sidewall is damaged, replacement is advised because the rubber on the sidewall is already thin, and further thinning due to damage increases the likelihood of a blowout. 2. Tread Wear Indicators: If the tire has worn down to the tread wear indicators—small raised bars located at the bottom of the tread grooves, which are 1.6 mm high (the legal minimum groove depth)—the tire should be replaced immediately, as continued driving is no longer safe. Using worn tires on wet roads can lead to hydroplaning, increasing the risk of losing control. This is because excessively worn treads cannot effectively channel water away from under the tire, leading to potential loss of vehicle control.
11
3
Share

What are the city license plate codes for Shaanxi Province?

Shaanxi Province's city license plate codes are as follows: Shaan A is Xi'an City, Shaan B is Tongchuan City, Shaan C is Baoji City, Shaan D is Xianyang City, Shaan E is Weinan City, Shaan F is Hanzhong City, Shaan G is Ankang City, Shaan H is Shangluo City, Shaan J is Yan'an City, Shaan K is Yulin City, Shaan V is Yangling Agricultural Demonstration Zone. License plates are plates hung on the front and rear of vehicles, typically made of aluminum, sheet metal, plastic, or paper, inscribed with the vehicle's registration number, registration region, or other relevant information. The license plate number is a legal mark registered by statutory authorities, permitting the vehicle to operate on the road, and serves as the identification number for the vehicle.
11
2
Share

Where is the daytime running light switch for the CS75?

cs75 daytime running lights do not have an independent switch. When the Changan CS75 vehicle is started, the daytime running lights will automatically turn on. Daytime running lights are lamps that make the vehicle more easily recognizable during daytime driving. These lamps are not for illumination but serve as signal lights. Daytime running lights can improve visibility and make the vehicle more conspicuous. This technology, specifically researched for daytime use, is more direct and effective than existing lighting devices. If equipped with daytime running lights, road users can detect and recognize the vehicle earlier and better. In the dark, if the driver turns on the regular headlights, the daytime running lights will automatically turn off. The CS75 has a body length, width, and height of 4650mm, 1850mm, and 1695mm respectively, with a wheelbase of 2700mm.
18
5
Share

Is It Normal for the Rear Wheels to Have Uneven Gaps Between the Wheel and the Wheel Arch?

It is not normal for the rear wheels to have uneven gaps between the wheel and the wheel arch. One side being higher than the other could be due to a significant difference in tire pressure between the left and right sides, excessive load on one side of the vehicle, or a damaged shock absorber on one side. A vehicle with one side higher than the other can compromise its balance and stability. In such cases, it is necessary to promptly identify the cause of the issue and carry out repairs. A significant difference in tire pressure between the two sides is also a common issue. In this case, it is necessary to check whether the tires are damaged or leaking. If a tire is damaged or leaking, it needs to be replaced. It is best to replace a pair of tires at the same time. Replacing only one tire may also affect the driving experience. Excessive load on one side of the vehicle can also cause the body to be higher on one side than the other. This is often due to the shock absorber system reaching the end of its lifespan. At this point, the shock absorber system can no longer provide sufficient support for the vehicle. The solution is to replace the shock absorbers and springs. In vehicles that have been in use for a long time, the shock absorber system is prone to failure. Common issues with the shock absorber system include oil leakage from the shock absorbers and loss of elasticity in the shock absorber springs. Both of these problems can lead to insufficient support from the shock absorber system, resulting in uneven height on both sides of the vehicle. The solution is to replace the shock absorber system.
3
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.