What to Do If Your Parked Car Gets Vandalized?

Why is there no signal in the car's reversing camera?

The reasons for no signal in the car's reversing camera are: 1. Poor line contact; 2. Damaged camera; 3. Faulty gear position sensor. The method to activate the car's reversing camera is: engage the reverse gear, and the reversing camera will automatically turn on. The car's reversing camera system uses a far-infrared wide-angle camera device installed at the rear of the vehicle, allowing clear visibility of obstacles behind the car through the display screen inside the vehicle. The function of the car's reversing camera is: to enable the driver to see the situation behind the car on the display when reversing, avoiding accidents caused by the driver not seeing the rear situation during reversing, thereby improving driving safety.

15

2

Share

Why is there water accumulation under the front passenger foot mat of a BMW 3 Series?

The reasons for water accumulation under the front passenger foot mat of a BMW 3 Series include clogged air conditioning drain holes, poor sealing, clogged sunroof drain holes, and driving through flooded areas. Clogged air conditioning drain hole: When the car's air conditioning is cooling, it generates a large amount of water, which is drained outside the vehicle through a drainage hose near the condenser connected to the bottom of the car. If this hose was not properly connected to the bottom of the car during manufacturing or is loose, this water can accumulate inside the vehicle. Poor sealing: The sunroof itself may have leaks or poor sealing; the vehicle body may also have poor sealing. Clogged drain hole: The sunroof drain hole may be clogged or detached, preventing water from draining outside the vehicle. Driving through water: This can occur when the vehicle is driven through a flooded area where the water is deep enough to enter the interior.

15

3

Share

What is the reason for the noise when the Baojun 730 air conditioner is turned on?

It may be the sound of the air conditioning compressor electromagnetic clutch engaging, which is normal. It could also indicate an issue with the air conditioning system. Reasons for clutch noise: When the cooling reaches the set temperature or the air conditioning pipeline pressure is too high, the compressor electromagnetic clutch will automatically disengage, and the compressor pulley will idle. When cooling is needed again, the compressor electromagnetic clutch will engage, producing noise during engagement. Air conditioning problem solutions: Adjust the internal pressure of the air conditioning pipeline, adjust the tightness of the air conditioning belt, and regulate the refrigerant dosage. It is advisable to visit a 4S store or a professional auto repair shop promptly.

10

4

Share

What are the brake alerts for the Envision?

There is a brake pad reminder. Brake Pads: When the brake pads wear to their limit, a warning will be issued to remind you to replace them promptly. Inspection and replacement should be done once 30,000 kilometers is reached. The replacement cycle for brake pads also depends on the driving habits of the owner. Failing to replace them in time can lead to loss of vehicle braking control, affecting driving safety. Brake Pad Replacement Method: Remove the wheel where the brake is located, take off the brake pads, clean the brake caliper, and apply noise reduction paste. Install the new brake pads onto the brake caliper, tighten the guide bolts, then reset the brake, ensuring the brake fluid is at the appropriate level. After replacement, test drive the vehicle to check the braking effect.

3

0

Share

What Causes the Clicking Sound When Turning a Car?

The causes of clicking sound when turning a car are: 1. Lack of lubrication or damage to the front wheel bearings; 2. Excessive clearance in the steering gear meshing; 3. Sound from the turn signal returning to position; 4. Friction between plastic components; 5. Abnormal noise from the steering wheel; 6. Aging of the steering tie rod ball joint. Methods for maintaining car tires include: 1. Regularly check tire pressure, ensuring it is neither too high nor too low; 2. Frequently remove debris from tire treads to prevent blowouts; 3. Inspect tire wear and replace them timely; 4. Perform four-wheel rotation to avoid excessive wear; 5. Avoid curbs and potholes to prevent tire sidewall ply breakage leading to bulges.

12

5

Share

What maintenance should be done at 60,000 kilometers?

At 60,000 kilometers, the following maintenance items should be performed: 1. Replace engine oil and oil filter; 2. Replace transmission fluid; 3. Inspect the braking system; 4. Check the power steering system; 5. Examine tire wear; 6. Replace spark plugs; 7. Clean the throttle body and fuel system; 8. Replace brake fluid. The purpose of maintenance is to filter impurities from the engine oil, air, and fuel, preventing them from entering the engine and affecting its normal operation. Regular maintenance can effectively extend the engine's lifespan, maintain the vehicle's cleanliness and proper technical condition, eliminate potential hazards, prevent malfunctions, and slow down the deterioration process.

12

1

Share

What to Do If Your Parked Car Gets Vandalized?

Why is there no signal in the car's reversing camera?

Why is there water accumulation under the front passenger foot mat of a BMW 3 Series?

What is the reason for the noise when the Baojun 730 air conditioner is turned on?

What are the brake alerts for the Envision?

What Causes the Clicking Sound When Turning a Car?

What maintenance should be done at 60,000 kilometers?

What is the fuel tank capacity of the Honda Greiz in liters?

Is the Borgward 1.4 engine a Volkswagen engine?

What is the 0-100km/h acceleration time for the Audi S5?

What is the fuel tank capacity of the new Magotan?