···
Log in / Register

What to Do If You're Late for the Driving Test (Subject 3)?

5 Answers
SadieDella
07/29/25 8:53pm

Communicate with the examiner or try to apply for the last batch of the test or a make-up test. If the application is not approved, it will be treated as a failure, and you can reschedule the test after 10 days. Below are some related extended information: 1. Number of attempts for Subject 3 test: There are only 5 test attempts in total. If you fail the test, you will have one free make-up test opportunity on the spot. If you still fail the make-up test, the test will be terminated. If you fail the fifth attempt, all previously passed subjects will be invalidated, and you will need to reapply for the driver's license, which means starting from Subject 1 again. 2. Canceling the test appointment: If you are certain that you cannot attend the test on the day due to personal reasons, cancel the appointment at least one day in advance to avoid it being treated as a failure and wasting a test opportunity. You can cancel the appointment through the Traffic Management 12123 app or the Comprehensive Traffic Safety Service Platform, or go to the vehicle management office if necessary. However, please note that multiple cancellations may affect the success rate of future test appointments, so students should consider carefully.

Was this review help?
11
3
Share
CharlieFitz
08/15/25 6:33pm

If you're late for the Subject 3 driving test, stay calm first. I once encountered a similar situation and immediately called the test center's hotline to explain the reason for being late. If you're on the way, don't hesitate, just rush to the test site. Examiners usually wait a few minutes, but don't exceed too long. It's recommended to plan your route in advance, such as checking traffic conditions with a map app, avoiding peak hours, and leaving a half-hour buffer. If you're seriously late, you may have to reschedule the test, which is both costly and time-consuming. So develop good habits, set multiple alarms on the test day, prepare the required documents the night before, and don't let mistakes affect your progress.

Was this review help?
2
4
Share
Expand All
ArabellaLynn
08/15/25 6:34pm

On the day of my third driving test, I overslept and was in a panic. I quickly messaged my instructor for help, and he suggested I contact the test center directly. While rushing to the test site, I called to explain my situation. The examiner replied that they could wait for me for 15 minutes. I made it just in time by pushing myself to the limit. At the entrance, I explained my situation with sincerity and was allowed to enter and take the test. Reflecting afterward, I realized how crucial it is to check the route and pack everything the night before. I recommend planning to arrive at least half an hour early to account for unexpected traffic or getting lost. While being late is a minor mistake, it can affect your mood and score.

Was this review help?
2
5
Share
Expand All
Tate
10/16/25 7:09am

When encountering a child being late for an exam, I suggest heading to the exam venue immediately. If there's still time, explain the reason for the delay to the examiner sincerely and ask for leniency. Some places allow a short delay for exams, so don't give up easily. Teach children to leave early in daily life, such as avoiding morning rush hour traffic and opting for public transportation for more reliability. Safety is the top priority.

Was this review help?
15
1
Share
Expand All
SanEllie
11/29/25 7:56am

When work gets busy, it's easy to lose track of time and be late for exams. I immediately called the test center to inform them, briefly explaining the delay due to reasons like traffic accidents. If the examiner is accommodating, quickly make your way to the venue. After the exam, reflect on time management issues: next time, simulate the route a day in advance and set multiple reminders. Avoiding lateness is a key factor.

Was this review help?
2
0
Share
Expand All
More Forum Discussions

can you put led bulbs in older car headlights

Yes, you can install LED bulbs in older car headlights, but it's not always a simple plug-and-play upgrade. The success and legality of the conversion depend heavily on your vehicle's original headlight housing design. Older cars typically use reflector housings , which are precisely designed to focus the light from a single filament in a halogen bulb. LED bulbs have multiple light-emitting points, which can scatter light incorrectly in a reflector housing, creating a blinding glare for oncoming drivers and providing you with a poor, uneven beam pattern. This is often illegal and will likely fail a vehicle inspection. The key is your headlight housing type. If your older car has projector housings , the swap is generally more successful. Projector lenses do a better job of controlling and focusing the light from an LED source, resulting in a clean cutoff line that minimizes glare. However, even with projectors, you may need to adjust the beam height after installation. Beyond the housing, you must consider the CANbus system . Modern vehicles use a CANbus network to monitor bulb function. Older cars lack this, but some aftermarket LED kits include error code eliminators or load resistors to prevent hyper-flashing in turn signals or dashboard warning lights, which may be necessary depending on your car. Here’s a quick comparison of the factors involved: Factor Halogen Bulbs (Original Equipment) LED Bulb Conversion Compatibility with Reflector Housings Excellent, designed for this housing Poor, often causes significant glare and illegal beam pattern Compatibility with Projector Housings Good Generally good, with a much cleaner cutoff line Light Output (Lumens) ~1,000-1,500 lumens ~3,000-12,000+ lumens Beam Pattern Focus Precise and compliant with regulations Unpredictable without proper housing match Legal Compliance (FMVSS 108) Fully compliant Often non-compliant unless part of a certified assembly Typical Lifespan 500-1,000 hours 30,000-50,000 hours Installation Complexity Simple replacement May require adapters, resistors, and beam adjustment Ultimately, for an older car with reflector headlights, the most reliable and legal upgrade is to replace the entire headlight assembly with a modern DOT/SAE-compliant LED unit. If you have projectors, a quality LED bulb kit is a viable option, but you should always aim the headlights on a wall after installation to verify the beam pattern is correct and not aimed too high.
14
5
Share

can you leave your car idling for a long time

Leaving your car idling for extended periods is generally not recommended. While modern engines are robust, prolonged idling (over 10-15 minutes) can lead to unnecessary engine wear, wasted fuel, increased pollution, and potential legal issues in some municipalities. The engine runs rich, leading to incomplete combustion that can foul spark plugs and contaminate engine oil more quickly. For most daily situations, turning the engine off is the better choice for your vehicle's health and your wallet. The primary issue is that the engine doesn't reach its optimal operating temperature while idling. This "cold" operation causes fuel to condense on the cylinder walls, diluting the oil and increasing wear on critical components like piston rings and cylinder liners. Furthermore, the alternator charges at a lower rate at idle, which can slowly drain the battery if power-consuming accessories like the air conditioner or headlights are running. The environmental and financial costs are significant. Idling for just 30 minutes a day can waste over $650 in fuel annually, assuming a national average gas price. Many states and cities have anti-idling laws, especially near schools, with fines that can be substantial. Idling Duration (Minutes) Estimated Fuel Consumed (Gallons, V6 Engine) Approximate Cost (at $3.50/gallon) CO2 Emissions (Pounds) 10 0.05 - 0.07 $0.18 - $0.25 1.0 - 1.4 30 0.15 - 0.21 $0.53 - $0.74 3.0 - 4.2 60 0.30 - 0.42 $1.05 - $1.47 6.0 - 8.4 120 (2 hours) 0.60 - 0.84 $2.10 - $2.94 12.0 - 16.8 There are a few exceptions. In extreme cold, idling for a minute or two allows oil to circulate before gentle driving. For hybrids, the gasoline engine may not even start during short stops. The best practice is to turn off your engine if you expect to be stopped for more than 60 seconds, except in traffic. This simple habit saves money and reduces engine wear.
11
4
Share

can you put boiling water on a car windshield

No, you should never pour boiling water on a car windshield. This action poses a high risk of cracking or shattering the glass due to a principle called thermal shock . Automotive glass, especially the laminated safety glass used for windshields, is designed to be strong but is extremely vulnerable to rapid temperature changes. When you pour boiling water (around 212°F or 100°C) onto a frozen windshield (which could be below 32°F or 0°C), the outer surface expands rapidly from the heat. However, the inner layer of glass remains cold and contracted. This creates severe stress within the glass, exceeding its structural tolerance and causing it to crack. The severity of the risk depends on several factors, including the exact temperature difference, the quality of the glass, and any pre-existing minor chips or imperfections that act as stress points. A small chip can quickly turn into a major crack spanning the entire windshield. While some types of tempered glass , used for side and rear windows, are more resistant to thermal shock than laminated glass, the practice remains unsafe for any automotive glass. The table below illustrates the approximate thermal shock resistance, or the maximum safe temperature change, for different types of automotive glass. This data is based on general industry manufacturing standards. Glass Type Common Use Key Characteristic Approximate Thermal Shock Resistance (ΔT) Laminated Glass Windshield Two glass layers with a plastic interlayer 90°F to 120°F (50°C to 70°C) Tempered Glass Side & Rear Windows Heat-treated for surface compression 150°F to 180°F (80°C to 100°C) Acrylic (Plexiglas) Race Car Windows Plastic polymer 140°F to 160°F (60°C to 70°C) Polycarbonate Armored Vehicles Extreme impact resistance 190°F to 220°F (90°C to 105°C) The safe and correct method is to use your car's defroster setting with the A/C on to dehumidify the air, combined with a plastic ice scraper. For a quicker start, use a 50/50 mixture of isopropyl alcohol and water in a spray bottle, which melts ice without damaging the glass or your car's paint.
16
4
Share

can you put different brand tires on your car

Yes, you can install different brand tires on your car, but it is generally not recommended and can compromise safety and performance. The most critical rule is to always install matching tires on the same axle. Mismatching brands, or more importantly, models and tread patterns, across axles can lead to unpredictable handling, especially in emergency maneuvers or poor weather conditions. The primary risks involve differences in key performance characteristics. Each tire model has a unique blend of attributes: Tread Pattern and Compound: This affects wet and dry grip. A tire with superior grip on the rear and weaker grip on the front can cause oversteer (where the car's rear end slides out), while the opposite can cause understeer (where the car plows straight ahead in a turn). Tread Wear Rate: If tires wear at different rates, you can quickly end up with a significant difference in tread depth between axles, which negatively affects braking stability and hydroplaning resistance. Size and Construction: Even with the same size marking on the sidewall (e.g., 225/45R17), subtle differences in actual dimensions, internal construction, and sidewall stiffness can affect the vehicle's handling balance. This is especially critical for all-wheel drive (AWD) and 4x4 vehicles . These systems are designed to operate with all tires having a nearly identical rolling circumference. Significant differences, often as small as 3/32nds of an inch in tread depth, can cause excessive wear and potential damage to the drivetrain's center differential or transfer case. For these vehicles, most manufacturers recommend replacing all four tires at once. Tire Characteristic Impact of Mismatching Example Scenario Tread Pattern Varying water evacuation; increased hydroplaning risk. New all-season tires on the front, worn all-season tires on the rear. Tread Compound Inconsistent grip levels; unpredictable cornering. Performance summer tires on the rear, touring all-season tires on the front. Tread Depth Altered vehicle balance and braking stability. 8/32" tread on the front axle, 3/32" tread on the rear axle. Size (Actual Diameter) Drivetrain strain in AWD vehicles; incorrect speedometer reading. New 225/45R17 tires on one axle, slightly smaller worn 225/45R17 tires on the other. Sidewall Stiffness Different cornering response and steering feel. Stiff run-flat tires on the rear, standard touring tires on the front. The safest approach is to always replace tires in complete sets of four. If that's not possible, ensure the two new tires are installed on the rear axle to maintain stability and that they are the same brand, model, and size as the tires you plan to keep.
16
1
Share

can you put diesel in a petrol car by mistake

No, you should never put diesel fuel in a petrol (gasoline) car. Doing so, even once, can cause severe and expensive damage to your vehicle's fuel system and engine. The most critical action is to not start the engine . If you've only added diesel and haven't turned the key, the damage is likely contained to the fuel tank and lines, making it a much simpler and cheaper fix. If you start the engine, the diesel will circulate and damage critical components. The core issue lies in the fundamental differences between the fuels and the engines designed for them. Petrol engines use spark plugs to ignite a fine mist of fuel. Diesel fuel is much oilier and less volatile; it's designed to ignite under high compression in a diesel engine. In a petrol car, diesel won't vaporize properly, clogs the fuel injectors, and provides poor combustion. This can lead to immediate symptoms like heavy smoke from the exhaust, stalling, a complete failure to start, or severe knocking sounds from the engine. The repair process is methodical. A mechanic must drain and flush the entire fuel system, including the tank, fuel lines, fuel pump, and fuel injectors. They will also need to replace the fuel filter. If the engine was run, the cost escalates significantly as diesel's improper combustion can damage the catalytic converter and oxygen sensors, which are very expensive components. Aspect of Damage/Repair Consequence / Typical Action Required Estimated Cost Range (USD) Misfueling Frequency Common enough that most repair shops have procedures for it. N/A Primary Immediate Action Do not start the engine. Push the car to a safe location. $0 (if you catch it in time) If Engine NOT Started Full fuel system drain and flush; replace fuel filter. $200 - $500 If Engine WAS Started Above, plus potential damage to fuel pump, injectors, catalytic converter, and oxygen sensors. $1,500 - $5,000+ Fuel Pump Wear Diesel lacks the lubricity of petrol, causing premature pump failure. $400 - $800 (part & labor) Catalytic Converter Damage Unburned diesel clogs and overheats the converter, destroying it. $1,000 - $2,500+ Fuel Injector Clogging Diesel's viscosity clogs precision injectors designed for petrol. $500 - $1,500 (for cleaning/replacement) Towing Cost Vehicle will likely need to be towed to a repair shop. $100 - $200
4
4
Share

can you put petrol in car with engine running

No, you should never refuel a car with the engine running. It is a significant safety hazard. While the probability of an incident might seem low, the potential consequences are severe, including fire or explosion. The primary risk is from static electricity or a stray spark from the electrical system igniting gasoline vapors, which are highly flammable and present around the fuel filler neck. Modern vehicles have multiple safety systems, but intentionally creating a dangerous scenario is never worth the minimal convenience. The primary dangers are: Ignition Source: The running engine, its electrical components, and the exhaust system are all potential sources of ignition. A single spark is all that's needed. Static Electricity: You can build up a static charge by getting in and out of your vehicle. A discharge when you touch the nozzle is a common cause of fueling fires, and a running engine increases the overall risk. Fuel System Sensors: Modern cars have sophisticated evaporative emission control systems (EVAP). Refueling with the engine on can confuse these sensors, potentially triggering a check engine light and storing fault codes because the system detects an unexpected pressure change. While the odds are in your favor, the stakes are incredibly high. The safety procedure is simple: turn the engine off, and if you need to, get back in the car during fueling (e.g., in cold weather), be sure to touch a metal part of the car away from the filler neck to discharge any static electricity before handling the nozzle again. Hazard Risk Factor Supporting Data / Authority Static Electricity Ignition High The Petroleum Equipment Institute cites static discharge as a frequent cause of fueling fires. Vapor Ignition from Engine Moderate to High National Fire Protection Association (NFPA) code 30A prohibits refueling with engines running. EVAP System Damage Low to Moderate Can trigger check engine lights; repair costs can range from $200-$500 for sensor replacement. Legal Violation High (at stations) Explicitly forbidden by posted signage at virtually all gas stations in the US; can result in fines. Potential for Catastrophic Outcome Extreme A gasoline fire can lead to total vehicle loss, severe injury, or fatality.
17
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.