What to Do If You Fail the Color Blindness Test for Driver's License Physical Examination?

1 Answers
VanTanner
07/30/25 7:05am
On-site re-examination is required. If the result remains unchanged, you need to go to a hospital at or above the county level (or a hospital designated by the traffic police) for further examination. To apply for a driver's license, you must meet the following physical conditions: 1. Height: For applying for large passenger vehicles, large trucks, or trolleybuses, the height must be above 155 cm; 2. Vision: For applying for large passenger vehicles, large trucks, or trolleybuses, the naked or corrected vision of both eyes must reach 5.0 or above on the logarithmic visual acuity chart. For other vehicle types, the naked or corrected vision of both eyes must reach 4.9 or above on the logarithmic visual acuity chart; 3. Color Discrimination: No red-green color blindness.
Was this review help?
13
4
Share
More Forum Discussions

What to Do When the Anti-Theft System is Locked and the Car Won't Start?

The solution when the anti-theft system is locked and the car won't start is: 1. Enter the car and shift the gear lever to neutral; 2. On the right side of the steering wheel, there is a red button on the center console—press and hold it for more than five seconds until you hear a beep, then release; 3. Press and hold the yellow button in front of the gear lever for five seconds, then release; 4. The electronic anti-theft lock on the center console will be deactivated; 5. Insert the car key into the ignition and start the vehicle. Car anti-theft systems utilize door lock control components and other elements. When someone attempts to forcibly enter the car without a key, open the hood or trunk, or when the battery is disconnected and reconnected, the system triggers the horn to sound and flashes the headlights and taillights for about one minute as an alarm.
11
3
Share

Is it necessary to warm up an automatic transmission car in place?

It is necessary to warm up an automatic transmission car in place for the following reasons: 1. When parked, the gear oil flows to the lower half of the transmission, and the upper half of the transmission cannot be lubricated when the car is cold; 2. After the car has been parked for a long time, the engine oil flows back into the oil pan at the lower part of the engine; 3. Before the engine reaches its operating temperature, the fuel supply system cannot effectively vaporize gasoline completely due to the lower temperature. The correct method to warm up the car is: 1. Start the vehicle and keep the air conditioning turned off; 2. Warm up the car in place at idle speed for 30 seconds to 1 minute; 3. Begin driving slowly once the engine runs smoothly; 4. Once the engine coolant temperature gauge rises by 1 to 2 bars, you can drive normally and turn on the air conditioning.
20
3
Share

The Structure and Principles of Automobiles?

Below is a detailed explanation regarding the structure and principles of automobiles: 1. Basic Structure: Automobiles are typically composed of four main parts: the engine, chassis, body, and electrical equipment. 2. Principles: The automobile injects fuel via the ECU, the ignition coil generates high-voltage electricity to supply the spark plug, the mixture of gasoline and air is ignited by the spark plug's electrical spark, causing combustion, which generates power. This power is transmitted through the belt, driving the wheels to rotate. Additional information: The function of the engine: It is to burn the supplied fuel to generate power. Most automobiles use reciprocating piston internal combustion engines, which generally consist of the engine block, crankshaft and connecting rod mechanism, valve train, fuel supply system, cooling system, lubrication system, ignition system (used in gasoline engines), and starting system. The chassis receives the power from the engine, enabling the automobile to move and ensuring it operates normally according to the driver's control.
7
4
Share

What does the red circle with an exclamation mark mean?

Red exclamation mark (specifically a circle with an exclamation mark inside), this represents a warning for the braking system, mainly indicating a braking system malfunction or low brake fluid level. Solution: Immediate inspection and repair of the braking system is required to avoid accidents. Apart from the red exclamation mark indicating a braking system fault, all other exclamation marks on a car are yellow, representing general faults, automatic transmission faults, abnormal tire pressure, and lighting faults. Below is a detailed analysis of these four situations: General Fault: A triangle with an exclamation mark inside. If this symbol lights up, it indicates a fault in the car's general performance or components and functions. Main issues include parking sensor faults, fuel cut-off system intervention or malfunction, external light faults, engine oil pressure sensor faults, etc. It is necessary to visit a 4S shop for inspection to identify the source of the fault. Automatic Transmission Fault: A yellow gear with an exclamation mark inside. This is the automatic transmission fault warning light, indicating a fault in the transmission or transmission lubricant below the normal range. Transmission oil should be replaced promptly. Abnormal Tire Pressure: A horizontal line under a bracket with an exclamation mark in the middle. This represents the tire pressure monitoring warning light, which lights up when the car's tire pressure is too low. Check the car's tire pressure and restore it to the normal range. Lighting Fault: A yellow bulb with an exclamation mark. This is the lighting fault indicator light, indicating a fault in the car's lights. Solution: Visit a 4S shop for inspection and repair as soon as possible, or conduct a self-check, focusing on commonly used bulbs such as turn signals, fog lights, and interior lights to identify the problem.
15
4
Share

Does speeding at the starting point of a section speed measurement count as speeding if the average speed within the section is not exceeded?

Speeding at the starting point of a section speed measurement does not count as speeding if the average speed within the section is not exceeded. The following is a detailed introduction to the section speed measurement system: 1. Function: The section speed measurement system establishes a monitoring and capture system by setting up cameras at road checkpoints to conduct real-time monitoring and capture of vehicles passing through the monitored area. It collects information such as vehicle speed, traffic flow, license plate number, color, approximate physical size, and driver characteristics. This information is then transmitted via a network to the public security traffic command center and traffic control sub-center databases for data storage, query, comparison, and other processing. 2. Working Principle: Section speed measurement involves setting up two adjacent monitoring points on the same road section. The principle is to calculate the average speed of a vehicle over that road section based on the time it takes to pass between the two monitoring points. The system then determines whether the vehicle has exceeded the speed limit for that section, thereby identifying speeding violations.
6
0
Share

What is the original engine oil model for the Roewe i5?

5w30 is the original engine oil model for the Roewe i5. Japanese and Korean car models, as well as domestic vehicles, generally use 5W-30 viscosity oil, while European and German vehicles mostly use 5W-40 viscosity oil, and American vehicles primarily use 5W-30 viscosity oil. The viscosity of engine oil changes with temperature, so special attention should be paid to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity. 5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, resulting in smoother cold starts for the car. The latter number represents the kinematic viscosity of the oil at 100°C. A higher value means the oil can maintain its viscosity index better at high temperatures, which can also be understood as better lubrication performance under high-temperature conditions. The method for changing the engine oil in the Roewe i5 is as follows: Wait for the engine temperature to cool down, allowing the oil to flow back into the oil pan; Use a wrench to loosen the oil drain plug and place an oil pan to catch the old oil until no more oil flows out. Start the engine and let it run for 30 seconds to allow the oil in the main oil passage to drain out; Use a special wrench to remove the oil filter; Apply oil to the seal of the new oil filter and tighten it clockwise by hand; Add the new engine oil through the oil filler cap on the engine valve cover, usually filling about three-quarters of the oil container; Start the engine and let it run for 5 minutes, checking for any leaks around the oil drain plug and oil filter. If leaks are found, repairs should be made; After stopping the engine, pull out the oil dipstick and check that the engine oil level is within the standard range.
20
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.