···
Log in / Register

What to Do If You Don't Receive Your Driver's License After Passing Subject 4?

3 Answers
OAthena
08/29/25 6:05am
You can contact the driving school where you registered or the vehicle management office to inquire about the reasons for not receiving your driver's license. In most cases, it is due to the delayed upload of the Subject 4 exam results. Under normal circumstances, you can receive your driver's license on the same day after completing the Subject 4 exam. More relevant information is as follows: 1. In a hurry: You can leave the examination venue after signing to confirm your score. Then, contact the driving school or the driving test center to explain the situation. The driving test center can mail the driver's license directly to the address specified on the license. Once you receive it, you can drive normally. 2. Note: Pay attention to the one-year probationary period. During this period, a probationary sign must be displayed on the rear of the vehicle. Accumulating 12 penalty points during the probationary period is not allowed, as it will extend the probation. Probationary drivers are not permitted to drive alone on highways. If driving on a highway, a passenger with at least three years of driving experience must accompany them in the front passenger seat.
Was this review help?
15
4
Share
KingRose
09/11/25 3:45am
After passing the subject four test, the driver's license is usually mailed to your home within 7 to 10 days. If you haven't received it after two weeks, it's recommended to immediately check the logistics status on the Traffic Management 12123 APP. If it shows that the license has been made but not shipped, directly call the driving school or the vehicle management office to follow up. Don't forget to check if the delivery address you filled in is correct. Last time, I encountered a situation where the courier said the address was unclear and the package was returned. If you can't find any information, quickly bring your ID card to the vehicle management office counter to check the reason—it might be that your test results were not recorded in the system. In short, don't just wait; actively following up is the right way.
Was this review help?
15
1
Share
Expand All
AnthonyDella
10/25/25 4:36am
I got stuck on the same issue the year I got my license, and finally found out it was due to the year-end backlog at the DMV for license printing. First, don’t panic—passing the subject 4 test means you’ve qualified, and your license is secured. Checking the progress on 12123 is the easiest way; logistics delays are common. Also, contact your driving school to help follow up, as document handovers often slip through the cracks. Double-check that your address and phone number are correct, as couriers frequently misplace items in mailboxes. If you’ve waited over a month, it’s best to visit the DMV directly—on-site reprinting is faster. Remember to bring your exam registration number; a quick face scan at the counter will get it sorted.
Was this review help?
5
3
Share
Expand All
More Forum Discussions

Can You Turn Right on a Red Light?

You cannot turn right on a red light. For more details, please see below: Cases where you can turn right: At circular traffic lights, you can turn right directly on a red, green, or yellow light, but you need to observe the road conditions. When the red light is on, right-turning vehicles can proceed if they do not hinder the passage of released vehicles or pedestrians. If caught by an electronic eye for not yielding to pedestrians, you will be penalized with 3 points. Therefore, to avoid penalties, you must yield to pedestrians when turning right. Cases where you cannot turn right: When all lanes on the road are straight lanes, you cannot turn right. Otherwise, it will be considered as not driving in the designated lane or violating the no-turn markings, with specific penalties determined by local traffic police. At intersections marked with 'No Right Turn on Red' or when the arrow light is red, you cannot turn right. If there is a 'No Right Turn' sign on the road, turning right is also prohibited and constitutes a violation of the no-turn sign or markings.
20
3
Share

What is the matching method for the 2006 Polo electric power steering?

Polo electric power steering requires a computer for matching. It is recommended to visit an authorized car 4S store and use specialized equipment for matching. Generally, professional technicians can complete the process in about ten minutes. Below is an introduction to the Electric Power Steering (EPS) system: 1. Introduction: The Electric Power Steering (EPS) system is a power steering system that directly relies on an electric motor to provide auxiliary torque. Compared with traditional Hydraulic Power Steering (HPS) systems, the EPS system has many advantages. The EPS mainly consists of a torque sensor, vehicle speed sensor, electric motor, reduction mechanism, and Electronic Control Unit (ECU). 2. Operation: When the driver turns the steering wheel, the torque sensor detects the steering direction and torque magnitude, sending voltage signals to the ECU. Based on the torque voltage signals, steering direction, and vehicle speed signals detected by the torque sensor, the ECU sends commands to the motor controller, enabling the motor to output steering assist torque of corresponding magnitude and direction, thereby generating auxiliary power. When the vehicle is not steering, the ECU does not send commands to the motor controller, and the motor remains inactive.
18
4
Share

What Causes a Car to Stall Suddenly After Starting?

There are several reasons why a car may stall shortly after starting, including severe engine carbon buildup, issues with the car's anti-theft system, ignition switch failure, or low fuel system pressure. Here are the details: 1. Severe engine carbon buildup: When there is excessive carbon buildup in the engine, fuel cannot burn effectively in the cylinders, leading to stalling after starting. In this case, the engine carbon needs to be cleaned promptly. 2. Activation of the anti-theft system: If the car's anti-theft system is triggered, the engine may start but fail to operate normally, causing the car to stall after starting. This issue commonly occurs after replacing the car key or its battery, so it's essential to reprogram the key after such changes. 3. Ignition switch failure: A faulty ignition switch can cause the car to stall after starting and trigger the malfunction indicator light. This is a complex issue that requires professional inspection and repair at a car service center or 4S shop. 4. Low fuel system pressure: Insufficient fuel system pressure prevents effective fuel combustion, necessitating a thorough inspection of the fuel system.
18
0
Share

What to Do When the Outside of the Windshield Has Fog That Won't Wipe Off?

If the fog on the outside of the windshield cannot be removed, you can use a defroster or open the window to expel the moisture. Below is an introduction to car windshields: 1. Introduction: The development of modern car exteriors is closely related to advancements in glass technology. Over 40 years ago, car windshields began using single-piece curved glass, gradually replacing flat windshields. 2. Function: Laminated glass involves bonding a transparent adhesive plastic film between two or three layers of glass, combining the toughness of plastic with the hardness of glass to enhance the glass's resistance to breakage. Tempered glass is made by quenching ordinary glass to create internal stresses, thereby strengthening the glass. When impacted, it breaks into small, blunt-edged pieces, reducing the risk of injury to passengers. Zone-tempered glass is a new variety of tempered glass that undergoes special treatment to maintain some clarity when cracked upon impact, ensuring the driver's field of vision remains unaffected. Currently, car windshields primarily use laminated tempered glass and laminated zone-tempered glass, which can withstand strong impacts.
20
3
Share

Why does the brake pedal automatically rebound when pressed all the way down?

The reason the brake pedal automatically rebounds when pressed all the way down is due to the ABS system functioning as a safeguard. Here are the specific details: ABS functioning as a safeguard: When you press the brake pedal hard and it rebounds or pulsates, it indicates that the ABS is working as a safeguard during emergency braking. Origin of the ABS anti-lock braking system: In emergency situations, drivers may slam on the brakes to control speed and prevent danger. However, when the braking system suddenly locks the wheels, it can cause the vehicle to lose lateral control. Moreover, continuously locking the brakes is not the most effective way to quickly reduce speed. Hence, the anti-lock braking system was developed. Specific function of the ABS anti-lock braking system: When the driver presses the brake pedal hard, the sensing device will repeatedly open and close the brake fluid circuit to prevent wheel lock-up and the resulting lateral deviation. At the same time, this enhances the most effective and safe stopping within a short distance. Therefore, the pulsation of the brake pedal is caused by the rapid opening and closing of the brake fluid circuit, which is a normal phenomenon.
16
0
Share

What materials should be brought for the first car maintenance?

The items required for the first maintenance include: driver's license; maintenance manual; warranty manual; owner's ID card; vehicle license; vehicle registration book; vehicle purchase invoice. Bring these to the designated first maintenance facility for the vehicle. Important note: Make an appointment with the 4S store in advance. The first maintenance refers to the initial service after a new car has been driven. The specific time varies by vehicle, typically after driving 5,000 kilometers or 6 months. It is essential to attend the first maintenance promptly, neither early nor delayed. The completion of the first maintenance marks the end of the car's break-in period, allowing it to be driven under standard load and normal speed as required by the vehicle. The timing of the first maintenance is calculated from the date of vehicle pickup. There are two indicator values for the first maintenance: mileage and time. Whichever indicator is met first will be the standard. The first maintenance items include: changing the engine oil and oil filter, cleaning the air filter, checking various fluid levels, inspecting the generator belt and wiper blades for damage, checking tire pressure and for any damage or bulges. Time required: Completing all tasks takes approximately 2 hours. The most critical aspect of the first maintenance for a new car is changing the engine oil and oil filter. When changing the oil, the oil filter must also be replaced. The choice of oil must refer to the "Vehicle User Maintenance Manual," as different vehicle models specify different oil grades. Maintenance precautions: Do not rinse the interior of the car body with water: Many people clean their cars during holidays, using water to rinse the exterior and wiping with a cloth. It is important to note that the interior of the car body should not be directly rinsed with water. If the floor mats are dirty, use a vacuum cleaner or remove them to clean with a brush and detergent, then dry before replacing. The rubber mats on the floor of the cabin have many drainage holes underneath. If water enters, it will not dry but flow through these holes to components like the gearbox, causing erosion and corrosion. The best practice is to use a vacuum cleaner for cleaning, followed by wiping with a cloth to prevent water accumulation. Do not mix different brands of antifreeze: If the car's antifreeze is low, it is recommended to drain the existing antifreeze and refill it with the same brand. Different brands of antifreeze have varying chemical properties and use different corrosion inhibitors. Mixing them may lead to unnecessary issues. Do not lubricate tire bolts and nuts: When bolts on a car become rusty, some may apply oil to make them functional again. However, lubricating the bolts and nuts on wheels can pose safety risks. At high speeds, the bolts and nuts may loosen or even fall off, leading to driving hazards.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.