What to Do If You Can't Drive Through S-Curves?

1 Answers
CharlieDella
07/25/25 5:12pm
S-Curves can be tricky, and crossing the line will result in point deductions. The best approach is to maintain a calm mindset and practice more. Here are some tips: 1. Reduce Tension: Stay relaxed and don't stress. Treating it as a regular practice rather than a test can ease the pressure. If you don't do well, you can always try again. Just follow the methods you've learned and have confidence in yourself. 2. Slow Down: Both crossing the line and exceeding the time limit will lead to point deductions, but it's better to exceed the time than to cross the line, as the latter results in more point deductions. When navigating curves, ensure you take the right angle—usually, turning the wheel when your seat reaches the curve will help the rear wheels pass smoothly.
Was this review help?
9
2
Share
More Forum Discussions

What brand is qeedar tires?

qeedar is a tire brand under Shandong Santai Rubber Co., Ltd. Here is some information about tires: 1. Introduction: Tires are round, elastic rubber products mounted on various vehicles or machinery for ground rolling. In 1845, R·w·Thomson, a civil engineer born in Scotland, invented the pneumatic tire and obtained a patent from the British government under the title "Improvement in Carriage Wheels and Other Vehicles." 2. Usage: Tires are usually mounted on metal rims to support the vehicle body, cushion external impacts, ensure contact with the road surface, and maintain driving performance. 3. Function: Tires often operate under complex and demanding conditions, enduring various deformations, loads, forces, and extreme temperatures. Therefore, they must possess high load-bearing capacity, traction performance, and cushioning ability. Additionally, they require high wear resistance, flexibility, and low rolling resistance with minimal heat generation.
19
2
Share

Is the Tayron GTE Hybrid Version Technologically Mature?

Tayron GTE hybrid version is technologically mature. Here are the relevant introductions: 1. Structural Features: It lies in the coordination between two clutches. 2. Five Modes: Including EV mode, hybrid mode, battery hold mode, battery charge mode, and GTE mode. Covering performance requirements for almost all road conditions. 3. Extended Information: The Tayron GTE is equipped with a hybrid power system consisting of an EA211 1.4T turbocharged engine and an 85kW permanent magnet synchronous motor, paired with a DQ400E six-speed wet dual-clutch transmission, delivering a comprehensive maximum power of 155kW and a comprehensive peak torque of 400N-m.
1
5
Share

Which city does the license plate 'Lu F' belong to?

Lu J is the license plate number for Yantai City in Shandong Province. The abbreviation for Shandong Province's license plates is 'Lu', and the following letter 'J' represents Yantai City. Below is a partial introduction to license plates from other areas in Shandong Province: 1. The provincial capital Jinan is 'Lu A', Qingdao is 'Lu B', and Zibo is 'Lu C'. 2. Zaozhuang is 'Lu D', Dongying is 'Lu E', and Weifang is 'Lu G'. Here is an introduction to the composition of license plate numbers: 1. The first character of the license plate is a Chinese character: it represents the provincial-level administrative region where the vehicle is registered, which is the abbreviation for each (province, municipality directly under the central government, autonomous region). 2. The second character of the license plate is an English letter: it represents the prefecture-level administrative region where the vehicle is registered, which is the letter code for each (prefecture-level city, region, autonomous prefecture, league), generally ranked according to the status of each prefecture-level administrative region by the provincial vehicle management office. 3. Additionally, when arranging the English letter codes for prefecture-level administrative regions, 'I' and 'O' are skipped, with 'O' often used for police cars or government units.
14
3
Share

Should You Turn Off the Engine While Waiting in the Car?

If the waiting time is less than five minutes, you can keep the engine running; however, if it exceeds five minutes, it is advisable to turn off the engine. Otherwise, apart from wasting fuel and increasing engine carbon deposits, sitting in the car for an extended period while waiting not only consumes more fuel but also poses safety hazards. This is because the carbon monoxide content in car exhaust is extremely high. Prolonged idling while waiting can easily lead to carbon monoxide poisoning if not careful, especially in underground parking lots where it is crucial to avoid idling for too long. The hazards of prolonged idling are as follows: 1. Due to extended idling, the engine temperature remains too low, leading to incomplete fuel combustion, which can cause carbon buildup, clog the fuel injectors, and severe carbon deposits may even cause the piston rings to seize or break. 2. During prolonged idling, poor fuel atomization can result in unburned atomized diesel condensing and washing down the cylinder walls, entering the lubricating oil and diluting it, thereby accelerating engine wear as the moving parts do not receive adequate lubrication. 3. Poor combustion during prolonged idling worsens engine emissions. If toxic gases enter the cabin, occupants may face the risk of suffocation. Additionally, the release of toxic gases pollutes the environment. Some countries have traffic regulations that prohibit prolonged idling (limited to 3-5 minutes) when parking on the roadside, with fines enforced by traffic police for violations. 4. Low idle speed reduces the oil pump speed, leading to low oil pressure and insufficient lubrication at critical points. 5. While the engine maintains a constant internal operating temperature, components like the exhaust manifold and catalytic converter rely on airflow for cooling. Prolonged idling can hinder heat dissipation in high-temperature engine parts and may even damage the catalytic converter due to excessive heat. Generally, it is best not to let the engine idle for more than 10 minutes.
3
1
Share

How to Properly Apply Car Window Tinting Film?

To properly apply car window tinting film, the following points should be noted: 1. After applying the film to the windshield, try to park facing the sun during the day. 2. Avoid rolling down the windows for three days after applying the film. 3. Do not wash the car for three days to prevent water from seeping in through the edges of the windows, which can cause excessive moisture at the edges of the glass and film, leading to peeling. 4. For vehicles with sunroofs, avoid opening the sunroof while driving, especially at high speeds, within three days to prevent air convection inside and outside the car, which may cause the upper edge of the windshield film to peel. 5. If bubbles appear at the edges of the tinting film, have them repaired at the installation site within 24 hours to prevent the adhesive from drying out and causing the film to become immobile, which may result in creases during handling. 6. Avoid using strong adhesive labels on the film for one month after application to prevent partial detachment. 7. In winter, try not to roll down the windows or wash the car for one week after applying the film.
20
2
Share

When to Use High Beam While Driving?

During driving, high beams should only be used when there are no other lighting facilities on the road and no oncoming vehicles. Below are the precautions for using low beam and high beam in cars: 1. Low beam must be turned on in the following situations: when driving in areas without streetlights at night, or during dusk when it is relatively dark or at dawn when light first appears; if encountering heavy fog, snow, or heavy rain that obstructs visibility, low beam must be turned on even during the day; on some roads where there are lighting facilities but the brightness is insufficient, low beam should also be turned on. 2. High beam should only be used when there are no other lighting facilities on the road and no oncoming vehicles. Otherwise, it will seriously interfere with the vision of other drivers and may even cause traffic accidents. Be careful not to mistakenly use high beam instead of low beam. 3. High beam must be immediately switched to low beam in the following situations: first, when there is an oncoming vehicle; second, when the distance to the vehicle ahead in the same direction is relatively close; third, when the road already has sufficient lighting, as well as when crossing railway intersections or returning to busy streets.
8
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.