What to Do If the Electric Vehicle Odometer Doesn't Accumulate?

What Causes the Reverse Camera to Not Respond When Shifting to Reverse?

When the reverse camera does not respond after shifting to reverse, the possible causes include the following: 1. The display unit may be frozen or slow to respond, which can usually be resolved by restarting the navigation system or the vehicle. 2. If the screen is black or blue, it may indicate an issue with the AV wiring. 3. For aftermarket reverse cameras, which typically draw power from the reverse lights, check if the reverse lights are functioning. If they are not, inspect the fuse. If they are working, examine the reverse camera wiring for looseness or poor connections. 4. If the factory-installed reverse camera does not respond when shifting to reverse, it should be taken to a 4S shop for inspection. 5. If the reverse camera does not display after shifting to reverse while the central control screen works normally and the reverse radar functions properly, it may be due to poor contact between the reverse camera module and the video cable. 6. The issue could also stem from a poorly connected or damaged vehicle camera.

1

Share

Can a cracked rear bumper be repaired?

If it's a minor crack, it can be repaired. The repair process is as follows: 1. First, remove the bumper and identify the area that needs repair. Then, use a plastic welding gun to heat and weld the crack from the back. 2. While heating the plastic welding rod, move along the crack. After welding, wait for the temperature to drop to complete the repair. 3. If there is severe deformation or breakage, it can only be replaced at a 4S shop. Below is an introduction to bumpers: 1. Definition: A car bumper is a safety device designed to absorb and mitigate external impacts, protecting the front and rear parts of the vehicle body. 2. Composition: A plastic car bumper consists of three parts: the outer panel, the cushioning material, and the crossbeam. The outer panel and cushioning material are made of plastic, while the crossbeam is formed by stamping cold-rolled sheet metal into a U-shaped channel. The outer panel and cushioning material are attached to the crossbeam.

2

4

Share

What to Do If You Lose Your BMW Car Key?

Solutions for losing a BMW car key are as follows: 1. Make every effort to find it, such as placing newspaper ads, seeking radio announcements, or posting on forums, while ensuring vehicle security during this period. 2. Use the spare key to unlock the vehicle and visit a 4S store to deactivate the lost key. 3. Use the password key to reconfigure a new one at a 4S store, requiring the purchase invoice, original purchase documents, vehicle registration certificate, and the owner's identification for configuration at the dealership where the car was purchased. 4. Utilize the VIN code, a 17-digit anti-theft password, which can be provided directly to the 4S store for key reconfiguration.

16

5

Share

Which Gear Should Be Used for Vehicle Climbing?

For manual transmission vehicles, you can use 2nd or 3rd gear when climbing a slope. For automatic transmission vehicles, you can use the S (Sport) or L (Low) gear, or you can also use the D (Drive) gear. Below is an introduction to vehicle gears: 1. Manual Transmission Vehicles: Divided into 1st to 5th gears, 1st gear is for starting, 2nd gear is used at 20-40 km/h, 3rd gear at 40-60 km/h, 4th gear at 60-75 km/h, and 5th gear for speeds above 75 km/h. 2. Automatic Transmission Vehicles: P is for Parking, R for Reverse, N for Neutral, D for Drive, S for Sport mode, and L for Low gear when going downhill.

2

1

Share

Piston Ring End Gap Standards?

Piston ring gaps are divided into three types: side gap, end gap, and back gap. Their specific values are as follows: 1. End gap, also known as the opening gap, refers to the clearance between the two ends of the ring when it is installed in the cylinder in a cold state and positioned at top dead center. It is generally 0.25~0.50mm. 2. Side gap, also known as the edge gap, refers to the clearance between the side of the piston ring and the piston ring groove after the ring is installed in the piston. The first ring has a larger gap due to higher operating temperatures, typically 0.04~0.10mm; other rings generally have a gap of 0.03~0.07mm. 3. Back gap refers to the clearance between the inner cylindrical surface of the piston ring and the bottom of the piston ring groove after the ring is installed in the cylinder, generally 0.50~1.00mm.

18

0

Share

What does the AC button in the car center console mean?

The AC button in the car is the air conditioning cooling switch, where AC stands for Aircondition. Here is an introduction to car air conditioning: 1. How to use the AC button: When the weather is hot and cooling is needed, start the car and press the AC button to blow cold air. 2. Introduction: The car air conditioning system is a device that cools, heats, ventilates, and purifies the air inside the compartment. It can provide a comfortable riding environment for passengers, reduce driver fatigue, and improve driving safety. 3. Function: The air conditioner can control the temperature inside the compartment, both heating and cooling the air to maintain a comfortable temperature level.

1

4

Share

What to Do If the Electric Vehicle Odometer Doesn't Accumulate?

What Causes the Reverse Camera to Not Respond When Shifting to Reverse?

Can a cracked rear bumper be repaired?

What to Do If You Lose Your BMW Car Key?

Which Gear Should Be Used for Vehicle Climbing?

Piston Ring End Gap Standards?

What does the AC button in the car center console mean?

How to Adjust the Tie Rod of the X-Trail?

Is the BMW X7 a Full-Time Four-Wheel Drive Vehicle?

How to Deal with Audi A4L Engine Oil Consumption?

What are the main failure modes of closed soft gear transmission?