What to Do If the Car Stalls in Water?

Does Tar Remover Damage Car Paint?

Tar remover is a powerful cleaning agent with certain corrosive properties. Prolonged residue of tar remover can also corrode car paint. After using tar remover to clean the car, rinse it with clean water again to avoid any residue. Usage: Suitable for any washable surface and can effectively remove heavy stains. Tar remover is an industrial-grade powerful cleaner used in households, cars, ships, and RVs, capable of strongly eliminating grease, ground stains, road stains caused by vehicles, and hard-to-remove grease around houses. Instructions: First, clean the car body thoroughly. Must be used in a well-ventilated area. Shake the bottle well before use. Confirm the spraying direction before use. Spray the product directly onto tar stains. Wait for a moment, then wipe the stain clean with a clean soft cloth. Tools and products needed: cloth, sponge, tar remover. Precautions: If accidentally comes into contact with eyes, rinse immediately with plenty of water and seek medical attention. If accidentally ingested, induce vomiting immediately and seek medical attention. For spray use, keep the aerosol can upright and at an angle of no less than 45° to the horizontal. Store in a place below 40°C, away from heat sources and open flames. Do not expose to direct sunlight, impact, puncture, or incinerate the can. Keep out of reach of children.

17

2

Share

What is the normal tire pressure for the Mercedes-Benz A200L?

The normal tire pressure for the Mercedes-Benz A200L is 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2 bar in winter and reduced by 0.1 bar in summer. This data is based on the international GBT2978-2008 standard requirements. To check the current tire pressure of the Mercedes-Benz A200L during daily driving, you can activate the tire pressure monitoring system, and the tire pressure values will be displayed on the central LCD screen of the instrument panel. The specific method is to press the LCD adjustment button on the left side of the steering wheel's combination instrument panel to switch to the tire pressure monitoring system interface. Generally, a tire pressure exceeding 2.8 bar is considered too high, while a tire pressure below 2.0 bar is considered too low. Hazards of excessive tire pressure: Reduced tire friction and adhesion, affecting braking performance; causes steering wheel vibration and deviation, reducing driving comfort; accelerates wear on the central tread pattern of the tire, shortening tire lifespan; increases body vibration, indirectly affecting the lifespan of other components; overextends the tire cords, reducing elasticity and increasing the load on the vehicle during driving. Hazards of insufficient tire pressure: Increases friction coefficient with the road surface, leading to higher fuel consumption; makes the steering wheel heavy and prone to deviation, compromising driving safety; increases movement in various parts of the tire, causing abnormal heat due to excessive rolling; degrades the function of cords and rubber, leading to delamination or cord breakage and excessive friction with the rim, damaging the bead area and causing abnormal wear; multiplies friction between the tire and the ground, rapidly increasing tire temperature, softening the tire, and drastically reducing its strength. High-speed driving may result in a tire blowout. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no seal on top, four small spikes at the bottom, and an exclamation mark inside), it is generally due to one of the following three reasons: Abnormal tire pressure: Usually triggers an alarm when below 1.8 bar or above 3.0 bar. In this case, tire inspection and pressure adjustment are required. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure is not reset in time, the system retains the old data, causing the indicator light to remain on. Simply perform a tire pressure reset to resolve this issue. Damaged tire pressure sensor: The tire pressure sensor, installed inside the tire and connected to the inflation valve, monitors tire pressure. If the sensor is damaged due to impact while driving, the tire pressure warning light will illuminate. For sensor damage, the only solution is to replace it with a new one.

15

0

Share

What are the vehicle types allowed for each driver's license?

Here is an introduction to the vehicle types allowed for each driver's license: 1. A1 License: Vehicle Type: Large Passenger Vehicle, Allowed Vehicles: Large Passenger Vehicles, A3, B1, B2, C1, C2, C3, C4, M. 2. A2 License: Vehicle Type: Tractor, Allowed Vehicles: Heavy and Medium Full Trailers, Semi-trailer Trains, B1, B2, C1, C2, C3, C4, M. 3. A3 License: Vehicle Type: City Bus, Allowed Vehicles: City Buses with a Capacity of 10 or More Passengers, C1, C2, C3, C4. 4. B1 License: Vehicle Type: Medium Passenger Vehicle, Allowed Vehicles: Medium Passenger Vehicles (Including City Buses with a Capacity of 10 to 19 Passengers), C1, C2, C3, C4, M. 5. B2 License: Vehicle Type: Large Truck, Allowed Vehicles: Heavy and Medium Trucks; Large, Heavy, and Medium Special Operation Vehicles, C1, C2, C3, C4, M. 6. C1 License: Vehicle Type: Small Car, Allowed Vehicles: Small and Mini Passenger Vehicles, Light and Mini Trucks, Light, Small, and Mini Special Operation Vehicles, C2, C3, C4.

5

4

Share

Do You Need to Press the Clutch When Decelerating?

You don't need to press the clutch when decelerating. Many drivers believe that pressing the clutch to cut off the car's power will make braking faster, but this is incorrect. If the car is moving slowly, pressing the clutch will result in slower coasting, and the speed can drop quickly after shifting gears. However, at higher speeds, pressing the clutch first may lead to serious consequences. Analysis is as follows: 1. When driving at high speeds, to decelerate efficiently, it's best not to press the clutch. Instead, utilize both engine braking and brake force to achieve rapid deceleration. At low speeds, if you need to decelerate slightly, the same principle applies—no need to press the clutch. However, if you need to reduce the speed significantly or come to a complete stop, you must press the clutch (or shift to neutral) just before the car stops. Otherwise, if the car's speed is very low or it has stopped while the engine is still outputting power, it will conflict with the stationary tires, causing the engine to stall. 2. When going downhill, if you feel the car is speeding up and want to decelerate, pressing the clutch before braking will have the opposite effect on your driving safety. Pressing the clutch downhill essentially "turns off" the engine's braking effect, causing the car to accelerate. If you use the brakes in this situation, they can easily overheat and fail. Therefore, when going downhill, avoid using the clutch unless necessary, such as when downshifting. Always drive in a lower gear according to the slope's steepness and rely on engine braking. If you need to brake, avoid pressing the clutch first unless the car is about to stop.

2

4

Share

What is the difference between the seizure and detention of a driver's license?

Here are the differences between the seizure and detention of a driver's license: 1. Difference: The detention of a motor vehicle driver's license refers to an administrative compulsory measure taken by traffic police during the execution of their duties. The temporary seizure of a motor vehicle driver's license refers to a penalty method by which the traffic management department of the public security authority lawfully suspends the motor vehicle driving qualification of a road traffic law violator for a certain period. 2. Detention of a motor vehicle driver's license: The main purpose of this administrative compulsory measure is to ascertain the facts of the road traffic violation committed by the party involved, in order to make a correct penalty decision. For example, traffic police may detain the motor vehicle driver's license of a road traffic law violator in cases such as driving under the influence of alcohol or drunk driving; driving a vehicle that is assembled or has reached the scrapping standard; or accumulating 12 points in a single scoring cycle, where it is deemed necessary to impose a penalty of temporary seizure or revocation of the motor vehicle driver's license. Before detaining the driver's license, the traffic police should verbally inform the party involved of the basic facts of the violation, the basis for the intended compulsory measure, and the rights the party is entitled to by law. After preparing the "Administrative Compulsory Measures Certificate" and delivering it to the party on the spot, the driver's license is lawfully detained. The detention period of the violator's driver's license lasts until the day the public security authority lawfully imposes an administrative penalty. 3. Temporary seizure of a motor vehicle driver's license: When imposing the penalty of temporary seizure of a motor vehicle driver's license on a driver, the driver's license should be transferred to the vehicle management office at the place of issuance within 15 days after the penalty decision is made. The driver's license should be returned according to the prescribed procedures after the temporary seizure period expires. This is equivalent to the suspension of the motor vehicle driver's license in the original "Road Traffic Management Regulations" and the original "Road Traffic Accident Handling Measures". After the public security authority implements the administrative compulsory measure of detaining the motor vehicle driver's license, it should investigate the illegal facts within the statutory time limit. If it is decided to impose the penalty of temporary seizure of the motor vehicle driver's license on the party involved, the decision should be made by the traffic management department of the public security authority at or above the county level.

7

2

Share

How to Distinguish Between Dry and Wet Dual-Clutch Transmissions?

Methods to distinguish between dry and wet dual-clutch transmissions: The clutch plates in a dry dual-clutch transmission are not immersed in transmission oil, whereas those in a wet dual-clutch transmission are immersed in transmission oil. Dual-clutch transmissions offer fast gear shifting and high transmission efficiency. Dry dual-clutch transmissions shift quickly, but they have poor heat dissipation, average reliability and durability, and less smooth gear shifting. Wet dual-clutch transmissions, while not as fast in shifting as dry ones, provide better heat dissipation, smoother gear shifting, and superior reliability and durability compared to dry dual-clutch transmissions.

7

2

Share

What to Do If the Car Stalls in Water?

Does Tar Remover Damage Car Paint?

What is the normal tire pressure for the Mercedes-Benz A200L?

What are the vehicle types allowed for each driver's license?

Do You Need to Press the Clutch When Decelerating?

What is the difference between the seizure and detention of a driver's license?

How to Distinguish Between Dry and Wet Dual-Clutch Transmissions?

Can I still apply for a driver's license if I forgot to have a medical examination for one and a half years?

Should the clutch be released quickly when shifting gears?

What is the Principle of Shock Absorption?

What is a Time Card?