What to Do If the Car Is Not Driven for Half a Year on a Business Trip?

2 Answers
KyleMarie
07/28/25 2:36pm
If the car is not driven for half a year, the following measures can be taken: 1. If the car is not driven for half a year, warm up the engine for a few minutes regularly, two to three times a month. 2. If it exceeds half a year without driving, drain the gasoline and disconnect the battery cables. 3. Use a jack to lift all four wheels off the ground to protect the tires. 4. Apply lubricating oil to the door hinges and seals. 5. Wash and wax the car—after drying—cover it with a car cover to prevent dust. It is best to park it in a garage and place some rodent repellent devices on the ground. Below is some related knowledge about vehicle maintenance: The engine is fixed to the frame by engine mounts, which are made of rubber. Over time, exposure to wind and sun will inevitably cause them to age. As parts that secure the engine, once the mounts age, they will inevitably lead to unstable engine fixation, resulting in vibrations. Therefore, if the car is relatively old, the engine vibrates noticeably, but the power output hasn’t changed much, it is recommended to focus on checking the engine mounts.
Was this review help?
13
5
Share
LaEthan
08/11/25 10:35pm
Not driving your car for half a year during business trips is indeed a common issue. Let me share some practical tips. First, address the battery problem – long-term parking can easily drain and damage it. It's best to remove the battery and store it in a cool place or use a car cover to prevent complete discharge. Then there's the tires – prolonged pressure can cause deformation and air leaks, so it's advisable to inflate them fully or lift the car using stands. The engine oil should also be replaced, as old oil can settle and deteriorate, harming the engine. Additionally, preventing rodents from chewing wires is crucial; place mothballs or repellents under the car to avoid wiring damage. Ideally, park indoors in a garage to minimize exposure to wind and sun. Upon return, don’t rush to start the engine abruptly; first check the tires, battery, and oil, then warm up the engine gradually. Remember to ask a friend to start the car periodically, just for about ten minutes, to keep the systems running. These small steps can save you money and hassle, ensuring your car runs smoothly when you return.
Was this review help?
18
5
Share
Expand All
More Forum Discussions

What Causes Difficulty in Starting a Car but It Still Starts?

Difficulty in starting a car but it still starts is usually caused by aging spark plugs, throttle body, or car battery. For gasoline vehicles, after removing the air filter to check and confirm there is no blockage, inspect the spark plugs, high-voltage wires, ignition coils, and fuel injectors. Poor ignition or inadequate fuel injection can lead to difficulty in accelerating. The reasons for difficulty in starting a car are as follows: Carbon deposits: Difficulty in starting caused by carbon deposits in the car, accompanied by slight shaking at idle speed, can be resolved by cleaning the throttle body, intake manifold carbon deposits, and fuel injectors. Weak battery: A weak battery is a more common issue, and the first thought when a car won't start is usually that the battery is dead. The solution is simple: just jump-start the car using another vehicle or battery.
13
0
Share

Can a car still run without coolant?

A car cannot continue to drive without coolant. The absence of coolant prevents proper circulation, causing the engine to overheat as it cannot dissipate heat effectively. In severe cases, this can lead to engine damage. The method for replacing coolant is as follows: Before completely replacing the coolant, conduct a thorough inspection to check for any leaks or cracks in the pipelines, with a focus on the five-way hose. Coolant flows through the five-way hose and is distributed to different parts of the car to function. If there are signs of coolant leakage in this section, replace the hose or resecure the connection as needed. Drain the old coolant and then flush the liquid channels with clean water. Add clean water to the coolant reservoir, then continuously inject water into the reservoir so that it flows through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to circulate the water. The water initially draining from the reservoir may appear slightly pink. Continue adding clean water until the outflowing water is clear. Note: Remember to remove the heater hose and drain the water from the heater core. After draining for about an hour, add the new coolant through the radiator hose. Then, pour another container of coolant into the coolant reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. As some air is expelled from the cooling system, the coolant level will drop. Add more coolant until it reaches the "MAXT" mark on the reservoir.
16
2
Share

What happens if you miss the scheduled driving test for Subject 2?

If you fail to attend the scheduled Subject 2 driving test, it will be marked as a failure. Here are the details: Regulations: According to the "Regulations on the Application and Use of Motor Vehicle Driving Licenses," applicants who cannot attend the test at the scheduled time must apply to cancel the appointment at least one day in advance. If an applicant does not attend the test at the scheduled time, the test will be marked as a failure. Test attempts: Each subject can be taken once, and those who fail can retake it once. If you do not attend the retest or fail the retest, the current test session will be terminated, and the applicant must reschedule the test. However, Subject 2 and Subject 3 tests must be rescheduled at least ten days later.
13
3
Share

What does the iDrive system mean?

iDrive system is the abbreviation of BMW's unique intelligent driving control system "intelligent-Drive-system". It represents a new, simple, safe, and convenient future driving concept, falling under the category of automated and informational driving systems. Some high-end cars and concept vehicles are equipped with this latest technological innovation. Below is a related introduction: Functions: iDrive is very easy to use. The eight main menus include in-car climate, communication (such as car phone), entertainment (CD/TV, etc.), navigation, information, BMW service support, function settings, and help menu. Equipment: The external display device of this system is a rotary controller located in the traditional gear shift position and an LCD display in the middle of the dashboard. The function of this knob is similar to a computer mouse. Through actions such as pushing, pulling, rotating, and pressing, it can control multi-level menus on the display screen and select hundreds of functions under the eight main menus.
6
4
Share

What Causes the Clicking Sound in the Scooter's Transmission Box?

Scooter gearbox noise could be due to damaged transmission gears, bearings, or problematic gear oil. Sometimes, poor brake shoe blocks might also cause abnormal sounds. Additionally, check for issues with the pulley, as faults here can transmit noise to the gearbox, making it sound like the gearbox is the source. Here's some extended information: Principle: Scooters use continuously variable transmission (CVT), where the principle involves the overrunning clutch driving the transmission box, ultimately transferring power to the rear wheel drive. Inside the transmission box, a small driving gear rotates a larger driven gear via a belt. Hazards: If gear incremental clearance or meshing clearance is too large, or the belt is too loose, it can cause gear displacement or poor engagement clearance during acceleration, leading to abnormal sounds. Similarly, when the throttle is released, the engine speed drops, altering the transmission ratio, and the belt and gear engagement changes, which can also result in abnormal sounds.
4
1
Share

What is the 1243 valve adjustment mnemonic for a 4-cylinder engine?

The valve clearance adjustment for a 4-cylinder engine can be summarized with the mnemonic 'Double, Exhaust, No, Intake.' However, different types of engines and the positions of their intake and exhaust valves may vary, leading to differences in the valve clearance adjustment sequence. Below is a detailed explanation: Valve Adjustment Sequence and Method: Taking a 4-cylinder engine with a known firing order of 1-3-4-2 as an example. First, position cylinder 1 at the compression top dead center (TDC) and adjust its valves. Then, rotate the engine crankshaft 180 degrees to position cylinder 3 at the intake bottom dead center (BDC) and adjust the clearance. Next, rotate the crankshaft another 180 degrees to position cylinder 4 at the exhaust top dead center (TDC) and adjust the clearance. Finally, position cylinder 2 at the power top dead center (TDC) and adjust the clearance. Adjustment Considerations: In addition to following the correct sequence, the size of the valve clearance is also crucial. If the valve clearance is adjusted too small, the valves may not close properly, leading to reduced engine power. If the clearance is too large, it will increase the impact frequency of the valve train components, accelerating wear. It can also cause delayed valve opening, resulting in improper engine operation and reduced power.
3
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.