What to Do If the BJ40's Brakes Feel Too Soft?

Where is the Besturn T55 engine produced?

The Besturn T55 engine is developed by FAW Car Co., Ltd. under China FAW Group Corporation and is a domestically produced engine. The engine model of the Besturn T55 is CA4GB15TD-30, with a maximum power of 124 kW, a maximum torque of 258 N·m, and a maximum horsepower of 169. For daily maintenance of the Besturn T55 engine, the following methods can be used: Use lubricating oil of the appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices in the intake and exhaust systems and usage conditions; for diesel engines, CB--CD grade diesel engine oil should be chosen according to mechanical load, with the selection standard not lower than the requirements specified by the manufacturer. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, its performance deteriorates, which can cause various problems for the engine. To avoid malfunctions, change the oil regularly based on usage conditions and maintain an appropriate oil level. When oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and oil cannot pass through the filter element, it may burst the filter element or open the safety valve, allowing oil to bypass through the relief valve, carrying contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. In small amounts, it remains suspended in the oil; in large amounts, it precipitates, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates properly but also extends the overall lifespan of the radiator and engine.

1

4

Share

What are the reasons for the Honda CR-V not accelerating when stepping on the gas pedal?

Honda CR-V not accelerating when stepping on the gas pedal is due to issues such as damaged spark plugs and clogged fuel lines. The specific reasons for the lack of power and acceleration are as follows: 1. Clutch slipping: Clutch slipping mainly manifests as the vehicle's speed not increasing with the engine's RPM during acceleration, preventing the engine's power from being fully transmitted to the drive wheels, resulting in weak driving performance, especially noticeable when going uphill. 2. Engine-related issues: The source of power is the combustion of fuel, and the engine is responsible for supplying fuel and converting chemical energy into mechanical energy. Therefore, when the car lacks power and accelerates slowly, the engine system should be a key area for inspection. 3. Engine oil system: The importance of engine oil is well-known—it ensures sufficient lubrication, reduces resonance, and improves the smoothness of engine operation. If the engine oil is insufficient for a long time, it can lead to reduced power and increased fuel consumption in mild cases, or piston knocking and mechanical damage to related components in severe cases. Additionally, fuel pump failure or a clogged fuel filter can also cause a decrease in engine power.

18

4

Share

What does it mean when the ABS light comes on in a Mercedes-Benz?

The ABS light can illuminate in various states, each indicating different fault causes and requiring distinct handling methods. Details are as follows: State 1: ABS warning light stays on (most common). Cause 1: The ABS wheel speed sensor's sensing part is covered by mud, sludge, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed and wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the dirt off the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Loose connections between system circuits or poor contact of the ABS relay leads to signal issues, causing system failure. Solution: Check the circuit connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. As the engine speed increases and voltage rises, the ABS warning light turns off. This may also occur if the ABS system's power supply voltage is too low due to poor terminal contact or grounding issues. Solution: Check the battery's specific gravity, inspect the charging system, and examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact of the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body's wiring connector; ABS computer malfunction. Solution: Loosen and then retighten the grounding screw of the hydraulic valve body, cleaning the contact surface if necessary. Check if the connector gap has widened. Replace the ABS or ABS/ASR computer if needed. State 4: ABS warning light illuminates during high-speed driving. Cause: At high speeds, the ABS computer detects a significant discrepancy between the rear and front wheel speed signals. This may also occur due to incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the sticker near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and push the brake switch linkage fully down with your fingers. Release the brake pedal to complete the self-setting position. Replace the brake light switch if necessary. If the ABS warning light is on, it is advised not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's trajectory, posing significant safety risks.

20

1

Share

Can the crystal coating be removed with alcohol?

The crystal coating can generally be removed with alcohol, but it may damage the car paint. It is recommended to have it handled by professionals. Below is relevant information about car crystal coating: 1. Function: Crystal coating is currently the most advanced car paint protection solution, featuring advantages such as corrosion resistance, scratch prevention, no cracking, and easy cleaning. It can protect the vehicle from minor daily scratches. Even when external forces exceed the elastic protection range of the crystal, it usually only leaves scratches on the crystal without damaging the paint. 2. Duration: The crystal coating is durable and stable, lasting 1-2 years, providing genuine protection for the car paint. However, crystal coating is relatively expensive, typically taking about 2 days to apply, and requires high technical skills from the technician.

3

4

Share

What is the FM frequency for car Bluetooth?

When using a car MP3 player, simply tune the radio to the same frequency as the MP3 player. Here are some related details about car Bluetooth functions: 1. Enables Bluetooth calling: It allows hands-free phone calls by connecting to your mobile via Bluetooth while driving, keeping both hands free and reducing traffic accident risks. 2. Automatic mobile phone recognition: No cables or phone holders are needed to connect your phone; drivers can control their phones without touching them, even keeping both hands on the steering wheel, using voice commands to answer or make calls. Users can conduct calls through the car's audio system. 3. Enjoy music outdoors: During holidays or road trips with friends, take out the car Bluetooth hands-free device, connect it to your phone, and enjoy your favorite music.

7

5

Share

Why can't the rearview mirror open automatically?

Rearview mirror may not open automatically due to wiring or rearview mirror assembly failure. Here is some information about rearview mirrors: 1. Introduction: The rearview mirror is a tool that allows the driver to directly obtain external information about the rear, side, and lower parts of the car while seated in the driver's seat. 2. Function: For the convenience of the driver and to prevent traffic safety accidents and ensure personal safety, all countries require that cars must be equipped with rearview mirrors, and all rearview mirrors must be adjustable. 3. Mirror surface shape: It can be divided into three main series: flat mirrors, spherical mirrors, and double-curvature mirrors. There is also a prism mirror, which has a flat surface but a prism-shaped cross-section, usually used as an anti-glare interior rearview mirror.

19

2

Share

What to Do If the BJ40's Brakes Feel Too Soft?

Where is the Besturn T55 engine produced?

What are the reasons for the Honda CR-V not accelerating when stepping on the gas pedal?

What does it mean when the ABS light comes on in a Mercedes-Benz?

Can the crystal coating be removed with alcohol?

What is the FM frequency for car Bluetooth?

Why can't the rearview mirror open automatically?

Is the UV radiation in the car as strong as outdoors?

Does the driver's license restore full points on the same day after passing the full-point test?

What is the fuel tank capacity of the Lincoln Continental in liters

How to Deal with Misfire in Cylinder 2 of the Engine?