What to Do If a Motorcycle Fails the Annual Inspection Deadline?

Do Hybrid Cars Need to Install a Charging Pile for Charging?

Hybrid cars do need to install a charging pile. Charging piles are convenient and fast, and plug-in hybrid electric vehicles (PHEVs) must frequently maintain sufficient battery charge to leverage their advantages. Since plug-in hybrid vehicles have relatively small power battery capacities, they cannot utilize fast charging. Instead, they rely on slow charging, which takes a longer time—typically around 3 to 10 hours to fully charge. Given the lengthy charging duration, relying solely on public charging stations is inconvenient, making home charging conditions crucial. While portable chargers can also be used to charge PHEVs at home, their 1.7KW charging power is too low, resulting in excessively long charging times. Therefore, installing a 3.3KW wall-mounted charging pile is recommended for convenience. In hybrid mode, the motor of a plug-in hybrid vehicle can also assist the engine by providing supplementary power, thereby reducing engine speed and lowering fuel consumption. When the battery charge is insufficient or falls below the SOC (State of Charge) value, the engine will allocate some power to drive the generator and recharge the battery. However, since the engine's speed increases during power generation, and energy loss occurs when converting fuel to electricity—combined with the heavier curb weight of PHEVs compared to conventional fuel-powered cars—this scenario leads to higher fuel consumption, which is not conducive to energy savings and emission reduction.

13

0

Share

Is it necessary to replace the rear axle rubber bushings?

It is necessary to replace the rear axle rubber bushings. Although there is no fixed replacement interval for rear axle rubber bushings, they should be replaced when damaged or aged. Worn-out rear axle rubber bushings will fail to provide shock absorption, causing chassis vibration and abnormal noises. Severe vibration may affect driving stability and compromise ride comfort. The rear axle rubber bushing serves as a flexible connecting buffer sleeve between the shaft and housing. Damaged bushings may lead to collisions between shaft components and could potentially cause misalignment between rear wheels and wheel arches, resulting in abnormal tire wear. Replacement method for rear axle rubber bushings: After lifting the vehicle, remove the two rear axle screws and oil pipes. Then use specialized tools for rear axle bushings to extract the old bushing. Apply lubricating grease to the new bushing before installing it. The rear axle refers to the components of the rear drive shaft that transmits power. It consists of two half-axles that can perform differential movement. The rear axle also functions as a device to support and connect the rear wheels. For front-wheel-drive vehicles, the rear axle acts as a trailing axle, serving only a load-bearing purpose. For vehicles where the front axle is not the drive axle, the rear axle becomes the drive axle, performing not only load-bearing functions but also driving, speed reduction, and differential functions.

14

5

Share

What is the method to determine a 30 cm distance between the car body and the roadside?

Methods to determine a 30 cm distance between the car body and the roadside include observing the position of the wiper protrusion and checking in the rearview mirror whether the rear door handle aligns with the sideline. In driving license tests, many scenarios require the distance between the car body and the sideline to be within 30 cm. When parking by the roadside, it is essential to carefully observe the parking space and check for any obstacles in front or behind. In areas with heavy traffic, drivers should always check the rearview mirror for approaching vehicles before opening the door to exit, to prevent collisions. Methods to maintain a 30 cm distance between the car body and the roadside: 1. Observe the position of the wiper protrusion: The wiper is a standard feature on every car, and its protruding part is easily noticeable when flat. During driving tests, you can determine the distance between the car and the sideline by checking if the wiper protrusion aligns with the right sideline. When they align, the distance is exactly 30 cm. 2. Check the rear door handle in the rearview mirror: During tests, when the position of the rear door handle reflected in the rearview mirror aligns with the sideline, the distance between the car and the sideline is exactly 30 cm.

19

5

Share

What is the difference between Brilliance BMW and BMW?

The differences between Brilliance BMW and BMW include different parent companies, different logos, different exhaust pipes, different glass brands, and differences in tires. The parent companies are different. BMW belongs to Bayerische Motoren Werke AG (BMW) in Germany. Brilliance BMW Automotive Co., Ltd. is a joint venture established by BMW Group and Brilliance China Automotive Holdings Limited. The logos are different. Brilliance BMW cars have the Brilliance BMW mark on the rear. The exhaust pipes are different; BMW has one thick pipe, while Brilliance BMW has two thin pipes. The glass brands used in the cars are different. The engine power is slightly different, with the imported version at 111W and the Brilliance version at 100W. The starting letters of the chassis numbers are different; imported models start with W, while domestic models start with L. Brilliance BMW has extended the wheelbase according to Chinese aesthetic preferences. If the rear letter is Li, it indicates a Brilliance BMW. Domestic BMW models include only the 3 Series and 5 Series, along with the BMW X1. Other series are mostly imported. For the 3 Series and 5 Series, the letters after the model name indicate the wheelbase: i denotes a wheelbase of 2888mm, while Li denotes 3028mm, which is 140mm longer than i. Models like the BMW 525Li, 523Li, and 530Li are all Brilliance BMW models.

16

0

Share

How to Reinspect a Vehicle That Has Not Been Inspected for Three Years?

The vehicle owner needs to personally submit a written application for reinspection to the traffic police department. Required documents include the vehicle license, third-party liability insurance certificate, and the original and copies of the vehicle and vessel tax. During the reinspection, fines must be paid, and 3 points will be deducted from the driver's license. According to the Road Traffic Law, vehicles that have not undergone the mandatory safety technical inspection (annual inspection) on time are not allowed to be driven on the road. Violators will be fined and have 3 points deducted from their license. In case of any traffic accident caused by the failure to undergo the annual inspection, the party involved will bear full or primary responsibility. Moreover, driving without inspection is considered illegal, and insurance will not cover any claims. The "Road Traffic Safety Law Implementation Regulations" stipulate: Article 16: Motor vehicles must undergo safety technical inspections according to the following intervals from the date of registration: passenger vehicles for commercial use must be inspected once a year within 5 years; after 5 years, once every 6 months; trucks and large or medium-sized non-commercial passenger vehicles must be inspected once a year within 10 years; after 10 years, once every 6 months. Required documents: ID card, vehicle license, compulsory traffic insurance policy, vehicle and vessel tax invoice (it's advisable to bring all relevant materials in case they are needed). The inspection must be conducted within the validity period of the compulsory traffic insurance. If the insurance has expired, it should be renewed before the inspection. All violations must be cleared. Essential items like a fire extinguisher and warning triangle are mandatory. Ensure that lights, brakes, etc., are functioning properly. The vehicle's appearance, including color and logos, must match the registration details. Owners with modifications are advised to remove them before the inspection.

20

1

Share

What is the purpose of placing the electric fuel pump inside the fuel tank?

The purpose of placing the electric fuel pump inside the fuel tank is to pump the combustion gasoline from the fuel tank into the fuel line and maintain a certain pressure to supply the fuel injector and cold start valve. Its function is to transport fuel from the fuel tank to the engine in the gasoline or diesel engine fuel supply system. Electric fuel pumps can be divided into roller type, turbine type, rotor type, and side channel type according to their different structures. According to the installation location, they can be divided into built-in type and external type. Principle of fuel pump structural forms: Vane pump (turbine pump) characteristics: The pulsation of oil pressure is small, the operation is smooth, the noise is low, and a pulsation damper is not required in the fuel supply system. It is easy to miniaturize, but the delivery efficiency is relatively low. Positive displacement pump roller type rotor type vane type characteristics: The oil pressure is high, but because the operation is not continuous, the oil pressure pulsation is large. Therefore, a pulsation damper is also required at the outlet end of the fuel pump. The turbine-type electric fuel pump is mainly composed of an electric motor, turbine pump, check valve, and safety valve. When the fuel pump is energized, the motor drives the turbine pump blades to rotate. Due to centrifugal force, the blades around the impeller press against the pump housing, carrying fuel from the inlet chamber to the outlet chamber. As the fuel in the inlet chamber continues to increase, a certain degree of vacuum is formed, sucking fuel from the inlet. The fuel in the outlet chamber continues to increase, and the fuel pressure rises. When it reaches a certain value, the outlet valve opens to output fuel. The outlet valve prevents fuel from flowing back to the fuel tank when the fuel pump is not working, maintaining a certain pressure in the fuel line to facilitate the next startup.

15

5

Share

What to Do If a Motorcycle Fails the Annual Inspection Deadline?

Do Hybrid Cars Need to Install a Charging Pile for Charging?

Is it necessary to replace the rear axle rubber bushings?

What is the method to determine a 30 cm distance between the car body and the roadside?

What is the difference between Brilliance BMW and BMW?

How to Reinspect a Vehicle That Has Not Been Inspected for Three Years?

What is the purpose of placing the electric fuel pump inside the fuel tank?

Why is the Hongqi E-QM5 not sold to individuals?

How Does a Hybrid Car Work?

What is the brand of Huawei's car?

Where should the jack be placed when changing a tire?