What to Do About Squeaky Car Doors When Opening and Closing?

1 Answers
McAnnie
07/29/25 6:09pm
Here are the solutions for squeaky car doors when opening and closing: 1. The automotive components between the car door and the body may require lubrication over time. If lubrication proves ineffective, another possibility is that the part is worn out and needs complete replacement. 2. The car door is connected to the body via hinges, similar to household doors. It's normal for hinges to produce noise after prolonged use. To ensure the smooth and quiet operation of the hinges, apply lubricating oil every 2-3 months for maintenance. 3. Open the car door to its maximum angle, clean the grease and dirt from the surfaces of the door limiter arm, limiter pin shaft, and connecting bracket, then apply an appropriate amount of grease to the upper and lower surfaces of the arm. Use specialized grease, such as HOTOLUBE from Tiger Head or Kluber's door hinge and slide channel grease.
Was this review help?
1
2
Share
More Forum Discussions

Is GAC Trumpchi considered a joint venture car?

GAC Trumpchi is not a joint venture car. Below is a detailed introduction to Trumpchi vehicles: 1. Introduction: It is an independent brand, and all models under Trumpchi are domestically produced. Trumpchi has a variety of SUVs and sedans, including SUV models like the GS3 and GS4. The GS7 is a mid-size SUV with dimensions of 4730 mm in length, 1910 mm in width, and 1770 mm in height, and a wheelbase of 2720 mm. 2. Engine Introduction: It uses two types of engines, a 1.8-liter turbocharged engine and a 2.0-liter turbocharged engine. The 2.0-liter turbocharged engine delivers 252 horsepower and a maximum torque of 390 Nm, with a maximum power at 5250 rpm and a maximum torque range from 1750 to 4000 rpm. This engine is equipped with DCVVT technology and direct fuel injection, featuring an aluminum cylinder head and a cast iron cylinder block. It is paired with a 6AT transmission. 3. Turbo Engine Introduction: The 1.8-liter turbocharged engine produces 188 horsepower and a maximum torque of 280 Nm, with a maximum power at 5500 rpm and a maximum torque range from 1750 to 4500 rpm. This engine features DCVVT technology and multi-point fuel injection, also with an aluminum cylinder head and a cast iron cylinder block. It is matched with a 6AT transmission.
17
3
Share

Where is the wireless charging button on the Haval H6?

Haval H6 wireless charging button uses an external adapter on the cigarette lighter. Here are the details: 1. Configuration: The H6's headlights adopt an integrated LED light source for high/low beam, paired with LED daytime running lights, ensuring enhanced driving safety both day and night. The side profile features a dual waistline design, appearing more streamlined while showcasing advanced stamping craftsmanship. The rear design is notably rounded, devoid of excessive chrome trim, exuding a minimalist feel. The full LED taillights echo the design of the headlights. 2. Dimensions: The new Haval H6 measures 4600mm in length, 1860mm in width, 1720mm in height, with a wheelbase of 2680mm.
14
5
Share

Why is the Haval F7 not selling well?

Haval H7 has experienced quality issues. The specific reasons for low sales are as follows: 1. Target consumer group: The Haval F7 targets younger consumers, but Haval's main audience is still middle-aged individuals aged 35-55. They prefer more mature and conservative models like the Haval H6 over the youthful F7, significantly reducing F7's sales among this demographic. 2. Serious quality issues: Additionally, the F7 faced severe quality problems in 2019, leading to a poor reputation that greatly impacted its 2020 sales.
12
4
Share

What are the reasons for the failure of the clutch pump in the Baojun 730?

The following are the related causes and symptoms of a faulty clutch pump in the Baojun: 1. Reasons for the failure of the clutch master pump: The clutch master pump may fail due to improper operation by the driver, poor quality of the pump body, damage to internal rubber seals, or insufficient clutch fluid leading to the damage of the clutch master pump. 2. Symptoms of a faulty clutch master pump: A faulty clutch master pump may exhibit oil leakage. The most obvious symptom is difficulty in shifting to the desired gear after pressing the clutch, or even inability to engage any gear, as the master pump failure can cause incomplete or no separation of the clutch.
17
4
Share

What are the functions of the three buttons on the tire pressure monitoring system?

The middle button is for reset, while the two side buttons are for adjusting brightness. The tire pressure monitoring symbol is a half-enclosed exclamation mark on the car dashboard. The function of the tire pressure monitoring system is to automatically and continuously monitor the tire pressure while driving, alerting the driver to low pressure or leaks to ensure driving safety. Tire pressure monitoring systems are mainly divided into two categories: indirect tire pressure monitoring and direct tire pressure monitoring, with the latter further classified into built-in and external types. Below are some key points about tire pressure: 1. Precautions: Regularly monitor tire pressure as it changes slightly with driving mileage. Over-inflation reduces the tire's contact area with the ground, increasing braking distance and compromising safety. Under-inflation can lead to sidewall rupture or even a blowout when driving too fast or for extended periods. 2. Adjusting tire pressure: As temperatures rise and driving speeds increase, internal tire pressure also rises. Therefore, it is advisable to slightly reduce tire pressure in summer. Conversely, in autumn and winter, increasing the tire pressure value appropriately can help reduce fuel consumption.
5
2
Share

How many liters difference between refueling in hot weather and cold weather?

There is a difference of about 0.4 liters per 10 liters. Below is the relevant introduction: 1. Gasoline: Gasoline is a volatile, flammable hydrocarbon mixture liquid obtained from petroleum through fractionation and cracking, which can be used as fuel. It appears as a transparent liquid, is flammable, and has a distillation range of 30°C to 220°C. 2. Principle of thermal expansion and contraction: Thermal expansion and contraction refer to the characteristic that objects expand when heated and contract when cooled. Due to the movement of particles (atoms) within the object changing with temperature, when the temperature rises, the vibration amplitude of the particles increases, causing the object to expand; but when the temperature drops, the vibration amplitude of the particles decreases, causing the object to contract.
18
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.