What to Do About Rusty Exhaust Pipe on Baojun 510?

1 Answers
Lawrence
07/30/25 9:35am
Solution for rusty exhaust pipe on Baojun 510: You can go to a 4S shop to have the exhaust pipe derusted and then spray it with high-temperature resistant rust inhibitor. The normal temperature of a vehicle's exhaust pipe usually ranges from 300 to 400 degrees, and can reach up to 600 degrees at high times. Due to the long-term alternation of cold and heat, rust may occur. The Baojun 510 is a compact SUV under the Baojun brand. The dimensions of this car are 4220mm in length, 1740mm in width, and 1615mm in height, with a wheelbase of 2550mm. In terms of power, this car is equipped with a 1.5L naturally aspirated engine across the entire lineup, with a maximum power output of 105 horsepower and a maximum torque of 135 Nm.
Was this review help?
6
3
Share
More Forum Discussions

What Causes the Abnormal Noise When Turning the Steering Wheel While Reversing?

The causes of abnormal noise when turning the steering wheel while reversing include friction between plastic components, friction between the steering column and the floor mat, failure of the clock spring inside the steering wheel, and aging of the steering tie rod ball joint. Friction between plastic components: The steering wheel is composed of various plastic parts. If the gaps between these parts are too small, friction will occur when the steering wheel is turned. For a new car, the steering wheel will adapt after some time of use. If the noise persists after this period, try reassembling the steering wheel. Friction between the steering column and the floor mat: If the aftermarket floor mat is too large and directly contacts the steering column, friction will occur as the steering column turns. Adjusting the position of the floor mat or replacing it can resolve the issue. Failure of the clock spring inside the steering wheel: If the clock spring is broken or its connector is not properly plugged in, replacing or securing it will fix the problem. Aging of the steering tie rod ball joint: Replacing the steering tie rod ball joint will solve the issue, but a four-wheel alignment is required after replacement.
7
4
Share

What Causes Sudden Abnormal Noises When Reversing?

There are several reasons why a car may suddenly produce abnormal noises when reversing, including wheel damage, shock absorber failure, transmission malfunction, and brake pad issues. Car Tire Damage: If a car tire has bulges or is punctured by foreign objects such as nails, it can cause abnormal noises when reversing or moving forward. In such cases, simply repairing or replacing the tire will resolve the issue. Car Shock Absorber Failure: When a car's shock absorber fails, abnormal noises may also occur when turning or driving over bumpy roads. This situation requires replacing the shock absorber at a repair shop or 4S store. Car Transmission Malfunction: If the car's transmission malfunctions, such as damage to the reverse gear, friction can cause abnormal noises. In this case, the transmission needs to be opened for inspection and replacement of the gears. Car Brake Pad Issues: Brake pad failure is a common cause of abnormal vehicle noises. Brake pad problems include improper installation, severe wear, or foreign objects trapped between the brake pad and caliper. The specific situation requires removing the car tire to inspect the brake pads before performing repairs, and in some cases, directly replacing the brake pads.
15
2
Share

Does Launch Control Damage the Car?

Launch control is very damaging to the car. It is an operation that puts stress on both the engine and transmission, affecting every moving component from the engine to the tires. Therefore, launch control is highly detrimental to the vehicle. Frequent use of launch control can directly lead to transmission failure. Hence, it is crucial to exercise caution when employing launch control. Most automatic transmission vehicles simulate launch control through programming, while manual transmission cars rely entirely on the driver's operation to execute a launch. During launch control, the engine is pre-revved to a certain RPM. For automatic transmission vehicles, the driver needs to simultaneously press the brake pedal and the accelerator pedal, then release the brake pedal once the launch control mode is activated. For manual transmission cars, the driver must press both the clutch pedal and the accelerator pedal while engaging first gear. Once the engine reaches the desired RPM, the clutch pedal should be quickly released.
4
4
Share

What Causes the Reversing Radar to Stop Speaking?

Reversing radar stops speaking due to reasons such as the radar switch being turned off, wiring faults, or malfunctions in the radar itself. Radar Switch Turned Off: Most vehicles have a control switch for the reversing radar on the central control panel inside the car. If it is turned off, the reversing radar will not function. The solution is to turn on the reversing radar switch. Reversing Radar Wiring Fault: When the reversing radar wiring ages or breaks, the radar will fail to operate normally. Timely repair or replacement of the wiring harness is required. Radar Itself Malfunctioning: If the reversing radar is found not to beep, first check whether the power cable of the main unit is properly connected and if there is current. Then inspect whether the radar main unit wires have become loose. If both aspects are fine, the issue lies with the radar itself. The radar's buzzer may be damaged, in which case purchasing and installing a new buzzer will suffice. Alternatively, the reversing radar control unit itself may be damaged, leading to the entire reversing radar system malfunctioning. A power reset can be attempted first. If the issue persists after resetting, it is likely that the control unit itself is damaged, necessitating replacement or repair of the reversing control unit.
2
2
Share

What is the matching range between gears and vehicle speed?

1st gear is used for normal starting or climbing very steep slopes, with a speed generally around 10 km/h; 2nd gear is a transitional gear for acceleration after starting or for low-speed driving, with a speed generally around 20 km/h; 3rd gear is used at speeds between 20-40 km/h, commonly used for urban driving; 4th gear is used at speeds between 40-60 km/h; 5th gear can be used at speeds of 60 km/h or above. When driving a manual transmission, the gear shifting sequence must be from 1st to 2nd to 3rd to 4th to 5th gear, and skipping gears is not recommended. The downshifting sequence should be determined based on the condition of your vehicle, generally downshifting when the engine speed drops below around 1500 RPM. The larger the gear, the slower the rotation speed, corresponding to a lower gear and slower vehicle speed; the smaller the gear, the faster the rotation speed, corresponding to a higher gear and faster vehicle speed. If the gear does not match the engine speed, a mismatch between engine power and transmission gears will occur, leading to the phenomenon of the vehicle jerking forward and backward.
6
3
Share

How Many Years Does an Idle Speed Motor Last?

The lifespan of an idle speed motor is consistent with that of the car, meaning it lasts until the car is scrapped. Under normal circumstances, the idle speed motor does not need to be replaced. The idle speed motor is a component that controls the idle speed of a vehicle and is inherently not prone to failure. Therefore, there is no precise or uniform answer to the lifespan of an idle speed motor. If you need to clean the idle speed motor, it is essential to go to a professional auto repair shop or a 4S store and have it cleaned by professionals. Cleaning it yourself improperly can easily lead to issues. If the idle speed motor is damaged, it can cause intermittent idle stalling, where the engine sometimes stalls at idle but runs normally after restarting. This situation can have certain impacts on driving. For example, if stalling happens to occur during emergency braking, it can cause significant hazards. Once the engine stalls, the brake vacuum booster will not function, and the power steering system will fail. Combined with the driver's panic, this can easily lead to accidents.
6
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.