What speed should the car reduce to when downshifting from third gear to second gear?

1 Answers
LeilaFitz
07/30/25 6:13am
When downshifting from third gear to second gear, the car should reduce its speed to 15-20 km/h. Whether upshifting or downshifting, the speed must match the gear. Only when the speed corresponds to the gear can the car's performance be at its best, and the thermal efficiency of the fuel be the highest. Below is an introduction to the speed matching for each gear: 1. First gear: Used when the speed is around 10 km/h. 2. Second gear: Used when the speed is around 20 km/h. 3. Third gear: Used when the speed is between 20-40 km/h. 4. Fourth gear: Used when the speed is between 40-60 km/h. 5. Fifth gear: Used when the speed is above 60 km/h.
Was this review help?
11
4
Share
More Forum Discussions

What is the engine model of the Song Pro?

The BYD Song Pro is equipped with a turbocharged engine codenamed BYD476ZQB, which has a displacement of 1.5 liters. Here are some details about this engine: 1. This engine delivers a maximum horsepower of 160 HP, a maximum power output of 118 kW, and a maximum torque of 245 N·m. The peak power is achieved at 5,200 rpm, while the peak torque range is between 1,600 and 4,000 rpm. 2. It features direct fuel injection, with both the cylinder block and cylinder head made of aluminum alloy. Additional information: 1. Dimensions. The BYD Song Pro measures 4,650 mm in length, 1,860 mm in width, and 1,700 mm in height. In terms of power, the entire BYD Song Pro lineup is equipped with a 1.5-liter turbocharged engine producing a maximum horsepower of 160 HP. 2. Transmission. The entire BYD Song Pro lineup uses a 6-speed dual-clutch transmission. 3. Suspension. The front suspension of the BYD Song Pro is a MacPherson strut independent suspension, while the rear suspension is a multi-link independent suspension. 4. Drivetrain. The BYD Song Pro features front-engine, front-wheel drive.
8
5
Share

What is the Difference Between Mineral Oil and Semi-Synthetic Oil?

Mineral oil and semi-synthetic oil mainly differ in the following aspects: 1. Mineral oil is produced by refining petroleum into base oil and then adding additives; semi-synthetic oil is made by chemically synthesizing base oil and adding additives. 2. Although mineral oil is inexpensive, its service life and lubrication performance are inferior to semi-synthetic and synthetic oils, and it also causes significant environmental pollution. Semi-synthetic oil is a product refined from mineral oil through hydrocracking technology, with purity very close to that of full synthetic oil. Its cost is slightly higher than mineral oil, making it an ideal transitional product from mineral oil to synthetic oil.
20
3
Share

What does the 'A' button in a car mean?

It refers to the Auto-Hold system. Here are some introductions about the Auto-Hold system: 1. AUTO-HOLD relies on the intelligent braking system, and only vehicles equipped with brake control systems like ESP can implement the AUTO-HOLD function. 2. Auto-Hold refers to an automatic braking function. Once activated, for example, when stopping at a traffic light, you don't need to pull the handbrake. It simplifies operations by avoiding the use of the handbrake or electronic handbrake, and for automatic transmission models, it eliminates the need for frequent switching between D to N or D to P.
19
2
Share

What is the tire pressure range for the Lavida?

The normal tire pressure for the Volkswagen Lavida is between 2.4 and 2.5 bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2 bar in winter and decreased by 0.1 bar in summer. This data complies with the international GBT2978-2008 standard. The Volkswagen Lavida's tire pressure monitoring system is displayed on the dashboard and is enabled by default. When the tire pressure is abnormal, the tire pressure warning light will illuminate to alert the driver. There is no physical button for the tire pressure monitoring system in the vehicle. Generally, a tire pressure exceeding 2.8 bar is considered too high, while a tire pressure below 2.0 bar is considered too low. Hazards of overinflated tires: Reduced tire friction and adhesion, affecting braking performance; causes steering wheel vibration and deviation, reducing driving comfort; accelerates uneven wear on the central tread of the tire, shortening tire lifespan; increases vehicle vibration, indirectly affecting the lifespan of other components; overstretches the tire cords, reducing elasticity and increasing the load on the vehicle during driving. Hazards of underinflated tires: Increases friction with the road surface, leading to higher fuel consumption; makes the steering wheel heavy and prone to deviation, compromising driving safety; increases movement in various parts of the tire, causing abnormal heat due to excessive rolling; weakens the function of the cords and rubber, leading to delamination or cord breakage and excessive friction with the rim, damaging the tire bead and causing abnormal wear; multiplies friction between the tire and the ground, rapidly raising tire temperature, softening the tire, and drastically reducing its strength. High-speed driving may result in a tire blowout. If the tire pressure monitoring indicator light illuminates (a yellow symbol with an irregular circle, no stamp on top, four small spikes below, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure: Typically, the system will alert if the pressure is below 1.8 bar or above 3.0 bar. In this case, the tires need to be checked and the pressure adjusted. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure is not reset promptly, the system will still record the previous data, causing the tire pressure monitoring light to illuminate. Simply reset the tire pressure to resolve this issue. Damaged tire pressure sensor: The tire pressure sensor, which monitors tire pressure, is installed inside the tire and connected to the tire inflation valve. If the sensor is damaged due to impact while driving, the tire pressure warning light will illuminate. For sensor damage, the only solution is to replace it with a new component.
10
1
Share

What is the 0-100 km/h acceleration time of the Hongqi H5?

According to official data, the Hongqi H5 is available in two engine displacements: 1.5T and 1.8T. The 1.5T model accelerates from 0-100 km/h in 9.2 seconds, while the 1.8T model achieves this in 8 seconds. Factors affecting a vehicle's 0-100 km/h acceleration time are as follows: Torque: Torque, in simple terms, represents how much force is available. The greater the torque, the stronger the force pushing the vehicle, resulting in faster acceleration. For example, the BMW 320i has a maximum torque of 205 Nm and accelerates from 0-100 km/h in 9 seconds. The Hongqi H5 1.5T model has a torque of 258 Nm and accelerates in 9.2 seconds. Transmission efficiency: The transmission serves as the medium for power delivery, inevitably involving power loss. Higher transmission efficiency leads to better acceleration performance. Generally, the ranking of transmission efficiency is as follows: manual transmission > dry dual-clutch transmission > wet dual-clutch transmission > AT transmission > CVT transmission. The Hongqi H5 1.5T is equipped with a wet dual-clutch transmission. Power-to-weight ratio: The relationship between horsepower and vehicle weight is called the power-to-weight ratio (unit: Hp/T). A higher power-to-weight ratio results in faster acceleration. For instance, the BMW 320i has a power-to-weight ratio of 106 Hp/T and accelerates in 9 seconds. The Hongqi H5 1.5T has a power-to-weight ratio of 111 Hp/T and accelerates in 9.2 seconds.
8
3
Share

Is the Porsche Engine in the Front or the Rear?

Some Porsche models have their engines in the front, while others have them in the rear. The Porsche Macan, Cayenne, and Panamera generally have their engines in the front, whereas the Porsche 911 has its engine in the rear. The Porsche 718 is a mid-engine model, with its engine located behind the passenger compartment and in front of the rear axle. Below are detailed specifications about the engine: 1. Maximum power is 185 kW, with a maximum torque of 370 Nm. 2. The maximum power RPM ranges from 5,000 to 6,800 per minute, and the maximum torque RPM ranges from 1,600 to 4,500 per minute. 3. It features hybrid injection technology and uses an aluminum cylinder head with a cast iron cylinder block. 4. The engine is paired with a 7-speed dual-clutch transmission. The Macan is equipped with a full-time all-wheel-drive system and uses a multi-plate clutch-type center differential. The front suspension of this car uses a double-wishbone independent suspension, and the rear suspension uses a multi-link independent suspension. The Porsche Macan also offers a more powerful 3.0T variant.
14
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.