···
Log in / Register

What speed is considered speeding for a motorcycle?

3 Answers
LeAnna
08/27/25 8:40am
Whether a motorcycle is speeding depends on the speed limit signs on the road. Penalty standards for motorcycle speeding: Motorcycles are also motor vehicles, just like cars. Depending on the severity of the offense, penalties can range from 2-12 demerit points and corresponding fines. During the annual inspection, offenders will need to attend training and take an exam. Motorcycle road regulations: When motor vehicles are traveling on highways, they should drive in the designated lanes. Small passenger vehicles with a design speed exceeding 130 km/h should drive in the second lane; large passenger vehicles, freight trucks, and small passenger vehicles with a design speed below 130 km/h should drive in the third lane.
Was this review help?
11
0
Share
KingstonLynn
09/09/25 7:20am
There is no fixed speed limit for motorcycles; it entirely depends on the roadside speed limit signs. Having ridden motorcycles for many years, I've seen all kinds of situations. For instance, highways usually have a speed limit of 120 km/h, so riding at 130 km/h would be speeding. On main urban roads, the limit is typically 50 or 60 km/h, and going slightly faster would be a violation. In school or residential areas, the speed limit is even lower, possibly 30 km/h, and riding at 40 km/h would be considered reckless driving. Speeding not only results in fines and penalty points but also increases the risk of accidents, especially in rainy conditions or on curves where stability is compromised. I recommend riders develop the habit of glancing at road signs before each trip or using the alert function on their mobile maps—safety first.
Was this review help?
20
3
Share
Expand All
AnnaRose
10/23/25 8:10am
Exceeding the speed limit on motorcycles is extremely dangerous. I always remind my fellow riders that speed limits are dynamic. On highways, the posted limit is 120 km/h—riding at 120 is acceptable, but going 125 is a violation. In urban areas, the limit is 50 km/h, and even a slight excess could be caught by speed cameras. Limits vary significantly by location: mountain roads may cap at 40 km/h, while industrial zones allow 60 km/h. Speeding leads to severe legal consequences, including fines ranging from hundreds to thousands, impacts on insurance claims, and, worse, increases the risk of crashes endangering lives. That's why I constantly monitor speed limit changes during rides to maintain a safe and reasonable speed.
Was this review help?
15
3
Share
Expand All
More Forum Discussions

Should the Positive or Negative Terminal Be Removed First When Disconnecting a Car Battery?

When disconnecting a car battery, the negative terminal should be removed first. Steps for disconnecting the battery: Turn off the ignition and remove the key; disconnect the negative battery terminal; remove the positive terminal protective cover; disconnect the positive battery terminal; remove the battery securing device; take out the battery; reverse the steps for installation. Note: During installation, connect the positive terminal first, followed by the negative terminal. After battery installation, perform necessary initial settings for your vehicle according to the user manual. Function of the battery: The battery is a crucial component in a car and is also a wearable part that requires regular replacement. When the engine is not running, the battery supplies power to the car; after starting the engine, the alternator powers the car's electronic devices. Battery replacement timing: The battery needs to be replaced periodically. A typical car battery lasts 3 to 4 years. Over time, the battery's charging capacity diminishes, indicating the need for replacement. Before winter arrives, it is advisable to check the battery. If the battery's internal resistance and voltage do not meet standard values, replacement is also necessary.
9
4
Share

What are the causes of abnormal rail pressure?

Abnormal rail pressure may occur due to the following reasons: Faulty pressure switch: The engine utilizes a high-pressure common rail injection system to control fuel supply, where multiple cylinder injectors are fed by a single high-pressure fuel rail. If the fuel in the rail becomes insufficient due to pressure-related issues, it reduces the engine's power output per unit time, leading to abnormal rail pressure. Clogged oil passage: As engine oil passes through the fine pores of the oil filter, solid particles and viscous substances are trapped in the filter. A clogged filter prevents smooth oil flow, potentially rupturing the filter element or activating the safety valve, allowing unfiltered oil to bypass through the relief valve and carry contaminants back to lubrication points. Airborne pollutants may accumulate around the PCV valve, potentially causing blockage. A clogged PCV valve can cause contaminated gases to flow backward into the air cleaner, polluting the filter element and reducing filtration efficiency. This results in dirtier air-fuel mixture intake, further contaminating the crankcase, increasing fuel consumption, and causing abnormal rail pressure.
10
3
Share

Is it acceptable if one side is wide and the other side is narrow in the reverse parking test for Subject 2?

In the reverse parking test for Subject 2, as long as the vehicle does not touch the solid line throughout the process, it is acceptable if one side is wide and the other side is narrow after parking in the garage. For example, one side being 25 cm and the other 35 cm, or one side 20 cm and the other 40 cm, are both acceptable. Although having one side wide and the other narrow does not result in point deduction, it may lead to some unnecessary operations, making the entire reversing process more complicated and harder to remember. If one side is too narrow and the other too wide, when exiting the garage and turning towards the narrow side, you must wait until the rear wheel of the narrow side reaches the corner of the garage before turning the steering wheel. If exiting towards the wide side, you can turn the steering wheel a little earlier, carefully observing the relationship between the wheel and the garage corner in the rearview mirror. If it is too close, you must adjust the steering wheel to the right, wait until the rear wheel passes, and then turn the steering wheel again to exit the test area.
7
5
Share

What faults will occur if the spark plug is broken?

Symptoms of a damaged spark plug: The car may experience difficulties in starting, low power, excessive exhaust emissions, increased fuel consumption, and other faults. Methods to determine if the spark plug is damaged: Remove the spark plug and observe its appearance color to judge its condition. A normal spark plug has an insulator skirt and electrodes that appear gray-white, gray-yellow, or light brown. A properly functioning spark plug has a reddish-brown insulator skirt, an electrode gap between 0.8-0.9mm, and no signs of electrode burning. If the spark plug is covered with oil or deposits but is not damaged, it can continue to be used after cleaning off the oil and deposits. If the spark plug is severely damaged, with signs such as blistering at the top, black streaks, cracks, or melted electrodes, the cause of the damage should be identified. After troubleshooting, replace the spark plug with a new one. Additionally, if the spark plug appears black as if smoked, it indicates that the wrong heat range was selected or the mixture is too rich, and oil is leaking into the combustion chamber.
8
1
Share

What is the diameter of a 6.5-inch speaker in centimeters?

6.5-inch speakers generally have a diameter of approximately 16.5 centimeters. Working principle of speakers: The working principle of an air horn is to use the airflow of compressed air to vibrate a metal diaphragm and produce sound. Therefore, it can only be used on vehicles equipped with an air compressor. Air horns are generally installed on large buses and heavy-duty trucks, especially for long-distance transport vehicles driving in mountainous areas or curves. Using an air horn can effectively alert pedestrians and oncoming drivers. This is because air horns have high volume, good sustain, pleasant sound, and can be heard over long distances. Air horns are typically cylindrical and use a combination of high-pitch and low-pitch horns. The working principle of an electric horn is to use electromagnetic force to vibrate a metal diaphragm and produce sound. It is a widely used type of horn in automobiles, classified into three structural forms: cylindrical, spiral, and cone-shaped, with spiral and cone-shaped being the most common. Classification of horns: Automobile horns are divided into air horns and electric horns based on their sound power; into cylindrical, spiral, and cone-shaped based on their appearance; and into high-pitch and low-pitch horns based on their frequency.
5
0
Share

Method for Adjusting Left and Right Rearview Mirrors in Subject 2 Parallel Parking

Method for adjusting left and right rearview mirrors in Subject 2 parallel parking: 1. First adjust the right rearview mirror so that the upper edge allows visibility of the rear door handle, while ensuring the front door handle is centered in the mirror (vertical position). The car body should occupy 1/4 of the mirror's area (the less the better, but too small may cause inconsistent width perception of ground lines compared to the left mirror). This setup allows better right-side visibility. 2. For the left rearview mirror adjustment, refer to the right mirror settings. However, the left mirror has an additional function - it must allow visibility of the left rear wheel during parallel parking. Ensure you can see the left rear wheel by leaning slightly, regardless of adjustment method (when the left rear wheel crosses the line at a 40-degree angle during parallel parking, full steering will guarantee entry). 3. During reverse parking, if the front guideline is absent in the test area and only the base line of the parking space is visible, you'll need to rely on the left rearview mirror. 4. With the front door handle centered vertically in the mirror, observe the left mirror during reversing. Stop when the front door handle aligns with the base line of the parking space. Note that individual height and seat position may require slight forward/backward adjustments, but the door handle and mirror positions remain constant reference points.
20
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.