What should the tire pressure generally be maintained at in summer?

2 Answers
DeMichael
07/24/25 5:38pm
Under normal circumstances, the tire pressure in summer should be maintained at 2.5, with a fluctuation range of ±0.2. Due to the effect of thermal expansion and contraction, tire pressure can be slightly higher in winter and slightly lower in summer. Vehicles equipped with a Tire Pressure Monitoring System (TPMS) can alert the driver when low tire pressure is detected. Below is some related information about tire pressure: 1. Tire pressure, strictly speaking, refers to the air pressure inside the tire. In terms of car maintenance, the engine is the heart of the car, and damage to the engine can lead to the end of the car's life. Similarly, tire pressure is like the blood pressure of the car, and its level has a crucial impact on the car's performance and power. 2. Tire pressure is an indicator of the car's load capacity. The load capacity of the car depends on the tire pressure. According to the relationship between the tire's load index, tire pressure, and load capacity, the higher the tire pressure, the greater the load capacity; the lower the pressure, the smaller the load capacity.
Was this review help?
1
4
Share
DiLilah
08/11/25 9:46am
As someone who drives frequently, I find tire pressure management particularly crucial in summer. High temperatures cause the air inside tires to expand, significantly increasing tire pressure and raising the risk of blowouts. I usually set my tire pressure according to the standard values marked on the door frame or in the manual, typically between 2.3 and 2.5 bar. Considering the high summer temperatures, I adjust it to be 0.1 to 0.2 bar lower than the standard value. Timing is also important when measuring; it must be checked in a cold state, meaning the car has been parked for at least 3 hours before testing. I make it a habit to check once a month, especially before highway trips. Actually, tire pressure that's too low is also unsafe, accelerating tire wear and increasing fuel consumption. It's quite dangerous to see some beginners neglecting this detail.
Was this review help?
20
0
Share
Expand All
More Forum Discussions

What does the three-electric warranty mean?

Three-electric warranty refers to the warranty regulations and policies covering the motor, battery, and electronic control system of electric vehicles. The following is a detailed introduction about electric vehicles: 1. Overview: Electric vehicles (BEV) refer to vehicles that use on-board power as the power source, drive the wheels with motors, and meet all the requirements of road traffic and safety regulations. Due to their relatively smaller impact on the environment compared to traditional vehicles, their prospects are widely optimistic. 2. Classification: Electric vehicles can be divided into three categories: battery electric vehicles (BEV), hybrid electric vehicles (HEV), and fuel cell electric vehicles (FCEV). The technology of pure electric vehicles is relatively simple and mature, and they can be charged wherever there is a power supply.
2
0
Share

Is the Transmission of the 2009 LaCrosse Bound to Fail?

The transmission of the 2009 LaCrosse is not bound to fail. Here is an introduction to the LaCrosse: 1. Vehicle Design: The Buick LaCrosse adopts Buick's latest family design language, featuring smooth and elegant body lines and a highly dynamic body proportion. The wing-shaped full LED automatic sensing headlights use advanced light curtain technology to create a more uniform and brilliant light curtain illumination effect. With a body length of 5026mm, width of 1866mm, height of 1462mm, and an ultra-long wheelbase of 2905mm, it provides a spacious driving and riding space for mid-to-large luxury sedans, offering a comfortable and free riding posture. The interior features 29 practical storage spaces, making it convenient to store commonly used devices and handbags. 2. Powertrain: The 2021 Buick LaCrosse family is equipped with two sets of driving systems, combining powerful performance with excellent fuel economy, and all models meet the 'China VI b' emission standards. At the same time, different power combinations will meet users' diverse needs with richer choices and further enhance the competitiveness of the Buick LaCrosse in the mid-to-high-end car segment.
4
2
Share

What are the consequences of mixing different colors of coolant?

Mixing different colors of coolant may cause a chemical reaction, leading to the coolant losing its effectiveness and failing to adequately protect the engine, potentially causing other adverse effects. Coolant replacement cycle: Vehicle coolant generally needs to be replaced every 2 years or 40,000 kilometers. This is just a reference period. For commercial vehicles with higher mileage, the replacement cycle should be shorter. Since driving conditions vary for each vehicle, the replacement should be based on actual usage. Check the coolant's condition regularly. If the coolant level is low, replenish it promptly. If suspended particles, sediment, or signs of deterioration or discoloration are observed in the coolant, replace it immediately and clean the system. How to choose coolant: The basic indicators of coolant are freezing point and boiling point. On the market, coolants are available with freezing points of -15°C, -25°C, -30°C, -40°C, etc. Generally, it is advisable to choose a coolant with a freezing point at least 10°C lower than the lowest temperature in your region.
13
3
Share

What is the fuel consumption of the 1.4T Jeep Renegade?

The fuel consumption of the 1.4T Jeep Renegade is 6.0-7.3L. Below is some related information about the Renegade: 1. Interior: This Jeep Renegade doesn't have the old-fashioned impression often associated with Jeep at all; the interior is full of personality and liveliness. The air vents, audio units, and gearshift base are all accented with different colors. Additionally, the three-spoke steering wheel integrates a multitude of functional buttons. 2. Model Introduction: The new Jeep Renegade 1.4T model has a wheelbase of 2570mm, with length, width, and height measuring 4245mm, 1805mm, and 1695mm respectively. The 75th Anniversary Tribute Edition is longer and taller, with a length of 4250mm and a height of 1723mm. Thanks to the BOXFORM professional design language, the new Jeep Renegade achieves a professional SUV body proportion. The four-wheel, four-corner design results in shorter front and rear overhangs, which not only enhances driving stability but also provides more interior space and excellent visibility.
16
2
Share

What Causes the Car to Shake When Accelerating to Around 40 km/h?

Shaking when accelerating to around 40 km/h may be caused by carbon buildup in the intake system, specifically a large amount of gummy carbon deposits near the valve seat and idle speed motor, leading to overly rich or lean air-fuel mixtures, or a dirty throttle. The following are daily maintenance methods for the engine: 1. Regularly clean the crankcase: During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Additionally, oil oxidation at high temperatures can create varnish and carbon deposits that stick to the pistons, increasing fuel consumption, reducing power, and in severe cases, causing piston rings to seize and leading to cylinder scoring. Therefore, regularly use a high-efficiency, fast-acting lubricating system cleaner to clean the crankcase and maintain engine cleanliness. 2. Regularly remove carbon deposits from the car: Carbon buildup is inevitable during fuel combustion. Excessive carbon deposits can cause issues such as difficulty starting, unstable idling, poor acceleration, backfiring during rapid acceleration, excessive exhaust emissions, and increased fuel consumption. These have many adverse effects on the engine. To prevent carbon buildup, maintain good driving habits such as frequently driving at high speeds, appropriately increasing shift RPMs, avoiding prolonged idling, and using clean gasoline.
3
2
Share

Which Side is the Brake?

For automatic transmission vehicles, the left pedal is the brake, and the right pedal is the accelerator. Here is some relevant information about car brakes: 1. Introduction to Brakes: Braking, also known as deceleration, refers to the action of stopping or reducing the speed of moving locomotives, vehicles, or other transportation tools and machinery. The general principle of braking is to fix a wheel or disc on the high-speed shaft of the machine and install corresponding brake shoes, belts, or discs on the machine base to generate braking torque under external force. The braking device, also known as a decelerator, is a mechanical braking device that can slow down the vehicle speed. 2. Classification of Brakes: Drum brakes, advantages of drum brakes, disadvantages of drum brakes, disc brakes, etc.
10
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.