What should be paid attention to in reversing into the garage in Subject 2?

2 Answers
DiBrynlee
08/30/25 7:08am
Subject 2 reversing into the garage precautions are as follows: 1. Learn to adjust the seat. After getting in the car, hold the steering wheel lightly with both hands, and the left foot can easily press the clutch pedal to the bottom without feeling strenuous. Both hands can easily turn the steering wheel. After adjustment, use fists to check the distance between the abdomen and the steering wheel. Generally, thin people should have two fists distance, while fat people should have one fist distance. Remember this distance. 2. Learn to adjust and observe the rearview mirrors. When adjusting the rearview mirrors, lower the mirrors to facilitate observing the ground markings. The adjustment method must be learned because during training and exams, it can be seen that the height and weight of students vary greatly. Only by adjusting the mirrors properly can better observation be achieved. 3. Adjust the distance between the car body and the sideline. Before entering the garage, the distance between the car body and the roadside line should be between 1.5 meters and 2 meters. If the distance is too small, it may cause the front of the car to cross the line when turning sharply to enter the garage. If the distance is too large, it may be difficult to enter the garage, or even impossible to enter. 4. Learn to use the clutch pedal to control the speed. If the speed is too fast, press the clutch pedal to reduce the speed. If the car is about to stop, release the pedal. The ideal state of pressing the clutch is that the speed is very slow but does not stop. 5. Learn to correct the direction after entering the garage. When correcting the direction, both hands should always be on the steering wheel. Do not turn the steering wheel at a large angle. The hands should move with the steering wheel without any sliding between them. Turn the steering wheel as much as needed and then return it to avoid losing direction.
Was this review help?
19
3
Share
StChase
09/12/25 4:06am
When I first learned reverse parking, I felt extremely nervous and kept failing by crossing the lines. The key is to control the car speed slowly without rushing, steer the wheel timely and accurately, and observing the rearview mirrors is crucial—don’t forget to check the angles and the car’s position. Beginners often make mistakes by steering too early or too late, causing the car to tilt and cross the lines. It’s recommended to practice more in an open space using reference points like aligning the car’s front with a pole. Keeping a calm mindset is important—don’t stress over the fear of failing the test. Simulating real scenarios can make the operation more proficient. This is also an essential skill in actual driving, helping to park safely and effortlessly.
Was this review help?
4
4
Share
Expand All
More Forum Discussions

Can I Transfer from One Driving School to Another?

You can transfer from one driving school to another. Here is relevant information about withdrawing from a driving school: 1. Withdrawal before taking the Subject 1 test: If you have already submitted the Subject 1 exam application at the driving management office and participated in the theoretical training organized by the driving school but haven't taken the Subject 1 test, filing fees, service fees, and theoretical training costs will be deducted. 2. Withdrawal after passing Subject 1: If you request withdrawal after passing Subject 1 and starting practical training, in addition to filing fees, service fees, and theoretical training costs, practical training fees will be deducted at a rate of 80 yuan per hour (based on IC card timing records).
16
1
Share

What Causes the Squeaking Sound in Car Seats?

Car seats squeaking can be attributed to several reasons, including loose seat screws, lack of lubrication in the sliding mechanism, or nearby debris. Below are detailed explanations and solutions: 1. Loose Seat Screws: If the screws securing the seat become loose, the seat may wobble and produce noise. Solution: Inspect and tighten the seat screws to prevent potential safety hazards. 2. Lack of Lubrication in Sliding Mechanism: Insufficient lubrication in the seat's sliding mechanism can cause noise when driving over bumpy roads. Solution: Remove the seat and reapply lubricant. 3. Debris Near the Seat: The noise might originate from either the seat itself or surrounding debris. Solution: Locate and remove any debris near the seat.
1
5
Share

Is there a Mobil 1 Fashion Edition engine oil?

Yes. Here is some relevant information about Mobil 1 engine oil: 1. Mobil 1: It is a fully synthetic engine oil brand. Since its inception, Mobil 1 has continuously improved its formula and raised standards, providing comprehensive performance protection for automotive engines, featuring multiple proprietary Anti-wear technologies. 2. Under ExxonMobil: The lubricant brand Mobil 1 was born in 1974 and has become a globally applied automotive synthetic engine oil. 3. Mobil 1 complies with: The latest API SN specification of the American Petroleum Institute, featuring multiple proprietary Anti-wear technologies that effectively help reduce engine wear, keep the engine clean, and meet the demands of modern engine technology and fuel economy with higher standards of engine protection and lubrication performance.
1
5
Share

What to Do When a Car Tire Bursts?

When a car tire bursts, avoid slamming on the brakes; instead, gradually reduce speed. Here are the relevant details: 1. High-speed driving when a tire bursts: A sudden tire blowout at high speed can cause the vehicle to veer sideways, and slamming on the brakes will worsen this veering, potentially leading to a rollover. While gradually slowing down, firmly grip the steering wheel and turn it in the opposite direction of the blown tire to maintain straight-line driving. 2. Tire blowout on a highway: If a tire bursts while driving on a highway, firmly hold the steering wheel, check the rearview mirror, and then move the vehicle to the right, ideally onto the right hard shoulder for safety. Note: Do not occupy the leftmost overtaking lane, as it poses a higher risk.
17
0
Share

Where is the original factory of Dunlop tires located?

Dunlop tires originated from the UK, so their original production location is in the United Kingdom. Below is relevant information about Dunlop tires. 1. Production Locations: In 1985, Dunlop Tires was acquired by Japan's Sumitomo Group and has production bases in both Japan and China. In 2002, Dunlop began constructing a factory in Changshu, Jiangsu, China. On August 13, 2010, Dunlop signed an agreement to invest $300 million in establishing its second Chinese factory in Changsha, Hunan. 2. Brand Advantages: Dunlop Tires consistently adheres to the philosophy that "tires can contribute to the Earth's environment," focusing on three core concepts: "low fuel consumption," "raw material development," and "resource conservation." Through high-precision analysis of rubber molecules and realistic simulation calculations of raw materials, Dunlop achieves comprehensive improvements in three key performance areas: low fuel consumption, grip, and wear resistance.
8
1
Share

How Many Gears Does a Motorcycle Have?

Motorcycles currently have two main types of gear systems: the rotary gear and the sequential gear (also known as the international gear). Here are the relevant details: 1. Gear Introduction: The rotary gear follows a 0-1-2-3-4-5-0 cycle, while the international gear follows a 1-0-2-3-4-5 non-cyclic pattern, with neutral located between 1st and 2nd gear. 2. Starting Method for Clutch-Equipped Bikes: After starting the engine, shift into first gear, gradually release the clutch lever while gently applying throttle. As you feel the bike start to move forward, continue to apply throttle while releasing the clutch, coordinating both actions until you smoothly start moving. Then, gradually shift up to higher gears using the same method. When stopping, first reduce speed, then pull the clutch lever, downshift, and brake. It's best to shift into neutral before turning off the engine.
3
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.