···
Log in / Register

What should be noted when charging an electric vehicle battery for the first time?

4 Answers
Lopes
09/05/25 7:16am
During the first charge, it is essential to use the original charger and start charging when the remaining battery level reaches 30%. The charging time for the first charge can be between 8 to 10 hours, with the maximum charging time not exceeding 12 hours to avoid damaging the battery. Below is relevant information: 1. Pure Electric Vehicles: Pure electric vehicles refer to vehicles powered by an onboard power source, using electric motors to drive the wheels, meeting all requirements of road traffic and safety regulations. Due to their relatively smaller environmental impact compared to traditional vehicles, their prospects are widely optimistic, although current technology is not yet mature. 2. Composition: The composition of electric vehicles includes the electric drive and control system, mechanical systems such as drive force transmission, and working devices to complete set tasks. The electric drive and control system is the core of an electric vehicle and the most significant difference from internal combustion engine vehicles. The electric drive and control system consists of the drive motor, power source, and motor speed control device, among others. Other components of electric vehicles are essentially the same as those of internal combustion engine vehicles.
Was this review help?
20
4
Share
DelAlexandra
09/17/25 7:30am
I just replaced the electric vehicle's new battery and need to be extra careful during the first charge to avoid messing it up. After the battery replacement, I'll first check all wire connections to ensure they're securely fastened without any looseness or corrosion. When charging, it's essential to use the original charger—don't just grab any fast charger as a substitute. Slow charging mode is the safest to prevent initial damage to the battery cells. Temperature is also crucial: avoid charging under direct sunlight or in freezing conditions. I usually opt for indoor charging at around 20°C. The first charge should be a full charge, ideally lasting 8-12 hours to activate the battery's internal chemicals and calibrate the management system. After charging, check if the battery overheats or emits any unusual odors, as these are danger signs. Remember, the first charge of a new battery impacts its long-term lifespan, so don't cut corners for convenience.
Was this review help?
16
1
Share
Expand All
OKeegan
10/31/25 8:01am
As an average car owner, I prioritize safety. When charging the new battery for the first time after replacement, I repeatedly verify proper installation and secure wiring connections without exposed parts. I choose a well-ventilated, dry charging location, avoiding kitchens or wet areas to prevent short circuits and fires. Using the manufacturer-provided charger, I avoid fast charging initially—slow charging helps the battery adapt smoothly. I monitor the entire charging process for hours, watching for abnormalities like smoke, unusual noises, or overheating—immediately cutting power if detected. The ideal charging duration follows the manual, typically 6-8 hours. After charging, I test the electric vehicle's operation to ensure normal functionality. Properly maintained new batteries can last years longer—safety always comes first.
Was this review help?
18
2
Share
Expand All
Bentley
12/14/25 8:09am
I prefer to keep it simple: After installing the new battery, charge it overnight in the garage or on the balcony using slow charging mode for the first time. The key is to use the original charger and avoid switching it randomly, stopping only when the battery indicator shows full. Maintain a comfortable environment during charging—neither too hot nor too cold—to prevent affecting battery activation. After charging, take a short ride to test the range and experience the new battery's performance. The whole process involves no complicated steps; the key is patiently waiting for a full charge.
Was this review help?
8
0
Share
Expand All
More Forum Discussions

What Causes Engine Shaking and the Malfunction Indicator Light to Illuminate?

When the engine malfunction indicator light comes on and the vehicle starts to shake, it is necessary to stop immediately and call for a tow truck to await rescue. The causes of this phenomenon include: 1. Poor combustion of the air-fuel mixture in the engine. When the mixture in the cylinder is too rich, the vehicle may experience knocking, shaking, and other symptoms. 2. Abnormal fuel supply pressure or a malfunctioning intake pressure sensor. If the fuel pump's supply pressure is abnormal or the intake pressure sensor provides incorrect readings or performs poorly, it can lead to body shaking and insufficient power. 3. Faulty operation of the spark plugs, high-voltage wires, or ignition coils. Poor performance of the ignition system or improper spark plug firing can also cause the engine malfunction light to illuminate, along with vehicle shaking and power loss.
10
4
Share

What Does It Mean When the Fender Screws Are Loose?

It indicates that the fender screws show signs of having been loosened or adjusted. Below is more information about fenders: 1. Introduction: Fenders, also known as wings or mudguards, are categorized into front fenders and rear fenders based on their installation positions. They serve as a type of cover for both motorized and non-motorized vehicles. 2. Installation Position: The front fender is installed near the front wheel and must accommodate the maximum space required for wheel rotation and bouncing. Therefore, designers use "wheel travel diagrams" based on the selected tire model and size to verify whether the fender's design dimensions are appropriate. The rear fender does not face issues related to wheel rotation interference, but for aerodynamic considerations, it typically features a slightly arched curve and outward protrusion.
18
4
Share

Can driving license points be sold? Will it have any impact in the future?

Driving license points cannot be bought or sold. Trading driving license points is an illegal act and will have consequences in the future. Penalties faced: For accepting penalties and deducting points on behalf of the actual driver for profit, the offender will have their motor vehicle driving license suspended for 6 months and be fined. Impact on the future: In severe cases, offenders may face detention for up to 15 days, have their motor vehicle driving license revoked, and be prohibited from obtaining a new license for five years. Having a criminal record may affect future generations' political vetting, and the revocation of the driving license will significantly impact daily life, causing inconvenience.
12
2
Share

What Causes the Car to Jerk When Releasing the Accelerator?

Car jerking when releasing the accelerator is most likely caused by the driver's lack of skill or transmission abnormalities. Below are the specific reasons for the car jerking when releasing the accelerator: 1. Caused by immature driving skills: Solution: Master the timing of gear shifting, skillfully coordinate the accelerator and clutch, do not release the clutch too quickly when starting, and avoid dragging gears when downshifting to decelerate. 2. The car jerking when releasing the accelerator could be due to transmission abnormalities: Solution: First, check whether the transmission fluid is insufficient or has deteriorated; if the transmission fluid is normal, it is recommended to go to a professional repair shop or 4S store for a diagnostic check of the transmission control system.
10
4
Share

What does seek mean?

On a car, the seek button refers to: the radio channel switching button, press it when switching channels. The usage method of the seek button is: in CD playback mode, pressing the left button can play the current music from the beginning; continuously pressing the left or right button will loop search the current disc from the current position. Other CD buttons on the car include: 1. mute - mute; 2. mode - mode selection; 3. ams - speed-sensitive volume; 4. vol - volume control; 5. band - channel selection; 6. scan - radio station search; 7. tune - sound effect selection; 8. int - preview button; 9. rpt - repeat playback; 10. rdm - random playback.
7
2
Share

Do BMW Run-Flat Tires Make Noise?

BMW run-flat tires do make noise. Run-flat tires are a type of automotive tire and are one of the important components of a vehicle. Characteristics of automotive tires: Automotive tires are one of the key components of a vehicle, directly in contact with the road surface. Together with the vehicle's suspension, they help absorb shocks during driving, ensuring good ride comfort and smooth driving. Functions of automotive tires: They ensure good adhesion between the wheels and the road surface; improve the vehicle's traction, braking, and off-road capabilities; and bear the weight of the vehicle. The important role that tires play in vehicles is increasingly being recognized by people.
12
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.