···
Log in / Register

What should be noted during the driver's probationary period?

3 Answers
McEverett
09/03/25 4:02am
During the probationary period, drivers should pay attention to affixing the probationary sign, and when driving on highways, they should be accompanied by a driver who has held a driver's license for more than three years. The "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China" require drivers to affix or hang a uniform probationary sign at the rear of the vehicle during the probationary period; otherwise, they will be fined. If a probationary driver fails to affix or hang the uniform sign, or if the sign cannot be properly recognized, or if the sign does not meet the requirements (such as signs like "New Driver on the Road" or self-printed signs), it will be considered as not having the sign affixed. "New drivers" can obtain the probationary sign from the vehicle management office (or branch) of the local traffic management department with their driver's license. When driving on highways during the probationary period, the driver must be accompanied by a driver who has held a driver's license for the same or a higher vehicle category for more than three years. The accompanying driver should sit in the front passenger seat to guide the probationary driver. If there is no accompanying driver or the accompanying driver does not meet the requirements, a fine will be imposed. In the event of a traffic accident, the accompanying driver will bear the corresponding responsibility for the accident.
Was this review help?
1
4
Share
DiJoseph
09/15/25 5:40am
I just passed my driver's license probationary period, and the most memorable thing is the safe driving techniques. Don't accelerate too quickly when starting, as it can easily stall or lose control; always signal in advance and check the rearview mirror and blind spot when changing lanes—beginners often overlook this detail, leading to collisions. Don't drive too fast, especially when turning or at intersections, to leave enough reaction time; practice reverse parking and parallel parking more to avoid scratches. Start by familiarizing yourself with city roads before attempting highways or nighttime driving, as insufficient light can easily lead to accidents. Be extra cautious in rain or snow, and slow down if the tires skid. In short, the probationary period is for accumulating experience—drive more but prioritize safety, and always check the car's condition, such as tire pressure, to prevent minor issues from turning into major mistakes.
Was this review help?
7
1
Share
Expand All
VanJoel
10/29/25 6:17am
Internship period rules must be strictly followed. Display the novice driver label prominently on the rear of the vehicle to remind others to yield; it's legally prohibited to drive on highways alone without an experienced driver accompanying, otherwise severe penalties apply. Pay attention to point deductions - accumulating 12 penalty points during the internship period may result in license cancellation. I've seen a friend's internship extended due to excessive speeding tickets. Regularly check if your insurance policy covers novice driver risks to avoid claim denials in accidents. Obey traffic signals strictly, don't run yellow lights, maintain safe following distances to prevent rear-end collisions. The internship period is crucial for developing standardized driving habits - never neglect these mandatory requirements.
Was this review help?
20
2
Share
Expand All
More Forum Discussions

What is Cold Bending Performance?

It refers to the ability of metal materials to withstand bending at room temperature without cracking. Below is a detailed introduction to cold bending performance: 1. Definition: Cold bending performance refers to the capability of steel to endure bending deformation at room temperature, which is an important process property of steel. The cold bending test can reflect the plastic deformation at the bending point of the specimen and reveal whether there are defects such as uneven internal structure, internal stress, and inclusions in the steel. 2. Standards: The qualified standard for the cold bending performance of steel bars is that after bending under the specified bending diameter D and cold bending angle α, there should be no cracks, scaling, or fractures at the bending point. According to the technical standards for steel bars, the values of D and α vary for different types of steel bars. For example, for Grade 335 crescent ribbed steel bars, α=180°. When the diameter is not greater than 25mm, the bending diameter D=2d; when the diameter d is greater than 25mm, the bending diameter D=3d.
12
3
Share

Is 215 kPa Tire Pressure Too Low and Needs Inflation?

Tire pressure of 215 kPa requires inflation as the normal range for tire pressure is between 230 kPa and 250 kPa. Driving with low tire pressure can cause severe tire wear and, in extreme cases, may lead to tire blowouts. Hazards of Overinflated Tires: Reduced friction and adhesion of the tire, affecting braking performance; Causes steering wheel vibration and misalignment, reducing driving comfort; Accelerates wear on the central tread pattern, shortening tire lifespan; Increases vehicle vibration, indirectly affecting the lifespan of other components; Overstretches the tire cords, reducing elasticity and increasing the load on the tire during driving; Decreases puncture resistance. Sharp objects like nails or glass can easily penetrate the tire, leading to internal cracks or blowouts. Solutions for Underinflated Tires: If no damage is visible, simply inflate to normal pressure and reset the tire pressure monitoring system; If a puncture is found, drive to a tire shop for repair and then reinflate; If the tire pressure warning reappears after inflation without any visible puncture, it may be due to a leaking wheel rim. Inspect and replace the rim if necessary.
7
3
Share

Why does the Mistra have high RPM but can't pick up speed?

The transmission is selected in a low gear, while the high vehicle speed is driven by the high engine RPM. The detailed explanation for the Mistra's high RPM but inability to pick up speed is as follows: 1. The transmission is selected in a low gear: While the high vehicle speed is driven by the high engine RPM. This situation is only applicable when the vehicle is climbing a steep slope with a heavy load, as it can provide high torque to give the vehicle sufficient traction. However, if this is used on flat roads or when the vehicle is unloaded, it will not only increase fuel consumption but also cause unnecessary wear and tear on the engine and vehicle, which is not recommended. 2. Clutch slipping: The clutch is installed between the engine flywheel and the transmission input shaft. When the clutch pedal is fully released, the power generated by the engine is transmitted to the transmission almost 100% through the clutch. If the clutch slips, it will result in slow acceleration when stepping on the gas. 3. Instrument malfunction: For example, if the engine tachometer shows a falsely high RPM, or the speedometer displays a speed lower than the actual vehicle speed, it can also create a false impression. Diagnosis and repair should be carried out based on the specific situation.
14
2
Share

What causes the clutch pedal of Hyundai Verna to become hard to press when the engine is hot?

When the clutch pedal becomes hard to press, it could be due to a malfunction in the clutch master cylinder. Possible causes include: a broken or jammed return spring in the master cylinder, swollen or flipped seals stuck at the compensation hole, or a one-way valve at the master cylinder end stuck and not returning to position. Below are relevant explanations: 1. Function of the clutch: The clutch is a component in the car's transmission system that directly connects to the engine. Its role is to smoothly engage or temporarily disconnect the engine's power from the transmission, reliably transmitting engine torque to allow the driver to perform operations such as starting, stopping, and shifting gears. 2. Usage of the clutch: If the clutch pedal has no free play, it can cause the clutch to slip, resulting in poor driving performance. If the clutch pedal's free play is excessive, it may prevent the clutch from fully disengaging, making gear shifting difficult. To check, press the clutch pedal until resistance is felt. This distance is the free play of the clutch pedal. The free play must be within the specified limit of 6-13mm. If it does not meet the requirement, it should be inspected and repaired at a service station.
3
4
Share

What is the fuel consumption of the Refine M3?

Refine M3 MIIT comprehensive fuel consumption: 7.9L/100km. Maintain the air filter to reduce fuel consumption: Dirty fuel and obstructed airflow can easily increase fuel consumption. The function of the air filter is to purify the air entering the cylinder. If the fuel exceeds standards or is too dirty, it can obstruct airflow, leading to increased fuel consumption. Tests have shown that if the fuel is too dirty or the fuel level is too high, fuel consumption can increase by more than 20%. Therefore, it is important to perform regular maintenance. After each cleaning, apply a certain oil film, and the lubricating oil at the bottom should also be filled according to the marked standard. Regularly remove carbon deposits to reduce fuel consumption: Excessive carbon deposits can increase fuel consumption by about 8%. When carbon deposits in the combustion chamber increase, they can easily cause spontaneous ignition of the combustible mixture, resulting in a decrease in power. If there is too much carbon deposit, fuel consumption can increase by about 8%. Therefore, during secondary maintenance or when the cylinder head is disassembled for other reasons, it is necessary to carefully remove carbon deposits from the combustion chamber and the top of the piston to reduce unnecessary fuel consumption.
14
5
Share

Why is there no air coming from the Q5's air conditioner?

Blower failure, clogged air filter, or control system malfunction can cause the air conditioner to stop blowing air. The specific reasons are as follows: 1. Blower failure: The blower is the core component for air circulation in the air conditioner. If it is damaged, the car's air conditioner will definitely not blow air. Blower failure may be caused by overheating of internal coils or capacitor damage. You can determine if there's a fault by turning the car's air conditioner to maximum speed and listening for the blower's sound. If a fault is detected, it's necessary to visit a 4S shop or repair shop for repairs, as DIY repairs are not advisable. 2. Clogged air filter: A clogged air filter is one of the reasons for the aforementioned air duct blockage and is the most common cause. Outside air passes through the air filter before entering the car, trapping many airborne particles, which can easily lead to clogging. You can remove the air filter to check if it's clean and replace it if it's too dirty. 3. Control system malfunction: If the above two reasons are not the cause, then the issue lies with the car's air conditioning control system. Faulty air vents, control switches, or the car's air conditioning computer could be the culprits. This is difficult to diagnose, and DIY repairs are challenging. In such cases, it's best to go to a 4S shop for repairs.
19
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.