What series does the Lynk & Co 03+ belong to?

What to Do When the Car is Covered with Exterior Wall Paint?

Solutions for removing exterior wall paint from your car are as follows: 1. Industrial Alcohol: Wipe with industrial alcohol. First, pour a small amount of the prepared alcohol onto a clean cloth, then wipe the areas with construction paint on the car to clean it off. 2. Paint Thinner: Purchase a bottle of paint thinner, spray it on the areas of the car body with paint, let the thinner soak in, then rinse and wipe clean with water. 3. Water Cleaning: For paint that hasn't completely dried, you can first wash the exterior wall paint off the car body with water or car wash liquid, then use car wash clay soaked in warm water to gently wipe the areas with exterior wall paint while spraying water. Avoid applying too much pressure during wiping to prevent tiny particles from scratching the car paint. 4. Sandpaper Polishing: For completely dried exterior wall paint, first clean the sand particles and dirt from the car paint surface, then use 2000-grit polishing sandpaper to remove the paint. Be careful to control the pressure during polishing to avoid damaging the original car paint. 5. Car Wash Service: For larger areas, you can go to a car wash. Remember to remind the staff not to rush and to wait until the paint softens before scrubbing.

1

2

Share

What are the reasons for the Audi showing insufficient tire pressure after just replacing the tires?

The reasons for the Audi showing insufficient tire pressure after just replacing the tires include a leaking tire valve, tire damage, deformed wheel rims, long-term overloading of the vehicle, and differences in tire quality. If the tire valve is leaking, it should be repaired or replaced promptly. If no damage is found during inspection, you can directly inflate the tire to the normal pressure and reset the tire pressure system. If the inspection reveals that the tire has been punctured, drive to a tire shop promptly for a repair and then reinflate the tire. If the system indicates insufficient tire pressure some time after inflation, but there is no puncture, it may be due to air leakage caused by deformed wheel rims. Deformed rims can also reduce the sealing performance of the tire. It is recommended to check the rims and replace them if necessary. Long-term overloading of the vehicle can cause uneven tire pressure distribution, so avoid carrying excessive weight. Differences in tire manufacturing processes can lead to insufficient tire pressure due to thermal expansion and contraction. It is advisable to choose higher-quality tires.

20

2

Share

Are the high and low beams of the Haval H6 integrated?

Haval H6's low and high beams are integrated, sharing a single bulb, and the light transition process is built into the bulb. Introduction to Car Headlights: Commonly known as headlamps, they include low and high beams. The primary function is for nighttime driving illumination. Low beams are used for urban roads with streetlights, while high beams are for roads without streetlights or highways in rural areas. There is also a high-low beam switch used for signaling or overtaking. Introduction to Position Lights: Mainly used at night to display the width and length of the vehicle, alerting other drivers and pedestrians to its presence. When visibility is poor through the rearview mirror or during rainy or foggy weather, position lights should be turned on to enhance driving safety. Introduction to Daytime Running Lights: To avoid increasing the battery load, it is not advisable to use headlights during the day. Hence, daytime running lights were developed specifically for daytime driving to alert other vehicles and pedestrians for safety. Typically, daytime running lights use white LED lights, which are energy-efficient, not too bright, and serve as a warning.

7

1

Share

What are the symptoms of transmission problems?

Below are the symptoms of car transmission problems: 1. Gear shifting impact and shaking while driving: This situation usually occurs in manual transmission cars. When the car is driving above 40 km/h, you can release the clutch directly when shifting gears without causing gear engagement failure or jerking. Therefore, if there is impact and shaking during gear shifting and acceleration, it indicates a problem. 2. High engine speed but insufficient power during driving: If the car delays 2-4 seconds to accelerate after stepping on the throttle, it is largely because the transmission has not engaged the "gear," causing the engine to run at high speed without power. In such cases, the fault cause needs to be checked. 3. Shaking phenomenon during smooth acceleration: Sometimes during acceleration, you may feel severe shaking in the car, which may indicate that the transmission is already damaged. Under normal circumstances, smooth acceleration should not cause jerking or shaking unless there is a problem with the car parts. Therefore, such situations should be checked. 4. Weak starting and slow acceleration: Normally, a car has sufficient power when starting. After releasing the clutch, the car should reach a speed of about 10 km/h. If the car still moves slowly after fully releasing the clutch, it is very likely that the transmission has a problem. 5. Feeling the gear engagement only after 2 seconds: Delayed gear engagement is likely due to burnt forward clutch plates.

20

4

Share

What does 'trip' mean in Volkswagen?

In Volkswagen and some models of other brands, the 'trip' button corresponds to the function of trip mileage, which records the mileage of each trip. Press and hold the 'trip' button to reset (clear) the trip mileage for the current journey. Introduction to ODO: The corresponding 'odo' stands for total mileage, with the full form being odograph or odometer. The total mileage cannot be reset. Introduction to trip: The smallest unit of trip mileage is 0.1 kilometers. The basic calculation method is the fuel consumption per 100 kilometers, which is also a parameter provided by the manufacturer. It is calculated by dividing the actual fuel consumption by the actual mileage traveled. That is, the fuel consumption per 100 kilometers equals the fuel consumption (liters) divided by the mileage traveled (kilometers) multiplied by 100.

4

0

Share

What is the ground clearance of the Envision S?

Buick's midsize SUV, the Envision S, is equipped with a MacPherson independent front suspension, and its ground clearance is 18.8 centimeters. Ground clearance of family sedans: Theoretically, the minimum ground clearance of ordinary family sedans generally ranges between 11-15 centimeters. Based on this parameter, a higher ground clearance (usually above 13 centimeters) indicates relatively better off-road performance, but slightly poorer stability at high speeds. Ground clearance below certain values: If the ground clearance is below 110 millimeters, the vehicle will have stable handling on highways but poor off-road capability. Some modern cars are equipped with air suspension systems that can automatically adjust the ground clearance, perfectly balancing both stability and off-road performance.

11

1

Share

What series does the Lynk & Co 03+ belong to?

What to Do When the Car is Covered with Exterior Wall Paint?

What are the reasons for the Audi showing insufficient tire pressure after just replacing the tires?

Are the high and low beams of the Haval H6 integrated?

What are the symptoms of transmission problems?

What does 'trip' mean in Volkswagen?

What is the ground clearance of the Envision S?

Why is Urea Added to Vehicles?

Is there any impact if a new car is registered after more than half a year?

What is the engine model of the Volkswagen Lavida 1.5?

What does the white exclamation mark on BMW 3 Series mean?