What's the reason for the sudden failure of the front fog lights?

1 Answers
LeAniyah
07/29/25 11:29pm
The reasons for the sudden failure of the front fog lights are: 1. If both front fog lights are not working, the possibility of both bulbs failing simultaneously is relatively small, and they can be checked later. 2. Check the fog light fuse; there are indications inside the fuse box. Find a fuse with the same amperage and replace it for testing. 3. If the fuse is not damaged, ensure the bulbs are not faulty, and inspect the wiring and fog light switch. Information about fog lights is as follows: 1. Fog lights generally refer to automotive fog lights installed at the front and rear of the vehicle. Because visibility is low in foggy conditions, the driver's line of sight is restricted. 2. Fog lights are divided into front fog lights and rear fog lights. Front fog lights are usually bright yellow, while rear fog lights are red.
Was this review help?
5
5
Share
More Forum Discussions

Does the Q5L have four-wheel drive?

q5l has four-wheel drive and is equipped with an on-demand four-wheel drive system. The on-demand four-wheel drive system does not provide power to all four wheels at all times; only in certain special situations will all four wheels receive power. The Q5L has a length, width, and height of 4753mm, 1893mm, and 1659mm respectively, with a wheelbase of 2908mm, and is equipped with a 7-speed dual-clutch transmission. The Q5L has a top speed of 210 km/h, with an engine maximum power of 140 kW and a maximum torque of 320 Nm. The tire specifications for this vehicle are 235/55R19, with a minimum ground clearance of 179mm, and it comes with ABS anti-lock braking, brake assist, automatic door locking while driving, cruise control, and rear radar.
17
3
Share

Why was the nx200t discontinued?

nx200t discontinued reason: The Lexus NX series models were recalled. Reason for the recall: In some vehicles, due to inappropriate production conditions of the acceleration sensor or pressure sensor IC chips inside the safety airbag control system, there is a possibility of internal IC circuit breakage, which may cause the airbag warning light to illuminate and prevent the airbags from deploying normally, posing a safety hazard. Below is relevant information about the Lexus nx200t: 1. Body dimensions: The vehicle measures 4630mm in length, 1845mm in width, and 1645mm in height, with a wheelbase of 2660mm. 2. Powertrain: Equipped with an 8AR-FTS turbocharged engine, delivering a maximum power of 175kw and a maximum torque of 350N·m.
9
5
Share

What Causes Brake Pads to Overheat?

The reasons for brake pads overheating are: 1. Poor return of the brake caliper causing brake drag; 2. Excessive and frequent braking during driving. The method for replacing brake pads is: 1. Remove the wheel where the brake is located; 2. Remove the caliper bolts and take out the brake pads; 3. Install new brake pads, tighten the guide bolts, and complete the replacement. The maintenance methods for brake pads include: 1. High-temperature resistance protection to prevent corrosion of the brake system, avoid brake pads seizing due to high temperatures, and eliminate brake squealing; 2. Clean the brake disc, brake drum, and any parts of oil stains, dirt, and friction dust to ensure good heat dissipation of the brake disc; 3. Regularly replace brake fluid; 4. Regularly check the thickness of brake pads or brake shoes.
4
2
Share

How to Replace Piston Rings?

When replacing piston rings, attention should be paid to side clearance and end gap. Here is a partial introduction: End gap: Refers to the gap between the two ends of the piston ring when placed in a standard ring gauge or in the unworn section of the cylinder bore. This gap should be controlled within 0.45-0.10mm, 0.39-10.10mm, and 0.50-1.00mm. This gap prevents the piston ring from seizing due to thermal expansion. Side clearance: Refers to the gap between the side of the piston ring and the ring land when the ring is placed in the piston ring groove. Excessive side clearance can affect the sealing of the piston, while insufficient side clearance can cause the ring to seize. The recommended clearance is 0.05-0.11mm for the first compression ring, and 0.03-0.09mm for the remaining compression rings and oil rings.
17
1
Share

Can Vehicle Scratches Exposing Primer Be Repaired?

Vehicle scratches exposing primer can be repaired. The methods for treating car scratches are: 1. Clean and dry the scratched area of the car, then gently rub the scratched area with sandpaper dipped in water; 2. Pour a small amount of cola onto a cloth and repeatedly wipe the scratched area; 3. Apply some medicated oil onto a cloth and repeatedly wipe the scratched area; 4. Clean the scratch thoroughly with a cloth, then squeeze toothpaste onto a damp towel or sponge and wipe the scratch up and down. Methods for maintaining the car's surface include: 1. Waxing; 2. Using a specialized machine to press vehicle protectant into the car paint to form a protective layer; 3. Using a coating machine to evenly spray liquid wax onto the car's surface for coating; 4. Performing surface grinding and polishing to treat the paint surface.
11
0
Share

How many days does it take to successfully schedule the Subject 4 exam?

Subject 4 can be scheduled either through the online vehicle management office or by the driving school. You can schedule the Subject 4 exam three days after passing Subject 3. The processing time for Subject 4 is much faster than for Subject 1, usually taking only two to three working days to successfully schedule. If scheduled through a driving school, you will typically be notified to take the exam in about a week. Subject 4 is also known as the Safe and Civilized Driving Knowledge Test. More details about the subject are as follows: 1. Main assessment content of Subject 4: Requirements for safe and civilized driving operations, knowledge of safe driving under adverse weather and complex road conditions, emergency handling methods for situations like tire blowouts, and post-accident handling knowledge. 2. Subject 4 exam paper: Consists of 50 questions, primarily in the form of case studies, images, and animations. The question types include true/false, single-choice, and multiple-choice questions, with a full score of 100 and a passing score of 90.
18
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.