What's the reason for the engine light on Wuling Rongguang V?

1 Answers
VanAiden
07/29/25 7:24pm
If the engine fault light is on while the engine is running normally, it is often caused by the use of cheap gasoline. Below are the differences between Wuling Rongguang and Hongguang: 1. Difference in body size: The dimensions of Hongguang are 4420mm*1685mm*1755mm (length*width*height), while Rongguang measures 4315mm*1660mm*1870mm. From this comparison, it is evident that Wuling Rongguang has a larger body size. 2. Different wheelbase: Hongguang has a wheelbase of 2720mm, whereas Rongguang has a wheelbase of 2700mm. A larger wheelbase generally offers better comfort.
Was this review help?
11
5
Share
More Forum Discussions

Can I pass the annual inspection after changing the rims?

Changing the rims will result in failing the annual inspection. Here are the specific details about changing rims: 1. If the modification of the rims has not been approved by the traffic management department in advance, the vehicle will not pass the annual inspection normally, and the original rims must be reinstalled before the inspection. 2. According to the relevant provisions of the current "Motor Vehicle Registration Regulations," any changes to the body color, model, performance, purpose, or structure of a licensed motor vehicle, including replacing the frame, body, or engine, require the owner to apply for a modification registration with the vehicle management office. Installing spoilers, body kits, or modifying exhaust pipes are, in principle, not allowed.
7
3
Share

What are the precautions for installing tires?

Here are the precautions for tire installation: 1. Tires of the same specification, load index, speed rating, structure, brand, and tread pattern should be installed on the same axle. 2. This tire must not be installed on the same axle with tires that have special markings (e.g., MO, RP, DT, etc.). 3. Always maintain the standard air pressure during driving, which should be based on the air pressure parameters provided by the vehicle manufacturer. 4. Stop using the tire when the tread wears down to the wear indicator. 5. The combination of tire and rim must undergo dynamic balancing before being installed on the vehicle. 6. Only personnel who have received professional training can install tires and perform dynamic balancing on the combination of tires and rims. 7. Do not purchase tires with barcodes torn off or barcode numbers smeared or scratched.
10
5
Share

How to adjust the rearview mirror of Audi A4L?

Audi A4L's rearview mirror adjustment button is located on the driver's side door panel. By rotating the knob to the corresponding position, you can perform the respective operation. Move the rotary knob to select the left or right rearview mirror direction, where you can adjust the mirror (driver or passenger side). Below is extended information about rearview mirrors: 1. The rearview mirror is a tool that allows the driver to directly obtain external information about the rear, side, and lower parts of the car while seated in the driver's seat. For the convenience of the driver and to prevent traffic safety accidents and ensure personal safety, all countries require that cars must be equipped with rearview mirrors, and all mirrors must be adjustable in direction. 2. Rearview mirrors have a field of view issue, which refers to the range that the mirror surface can reflect. The industry proposes three elements of the field of view: the distance between the driver's eyes and the rearview mirror; the size of the rearview mirror; and the radius of curvature of the rearview mirror. These three elements are interrelated. When the distance and size of the rearview mirror are the same, the smaller the radius of curvature of the mirror, the larger the field of view reflected by the mirror. When the radius of curvature of the mirror is the same, the larger the size of the mirror, the larger the field of view reflected by the mirror. At the same time, rearview mirrors also have a reflectivity index. The higher the reflectivity, the clearer the image reflected by the mirror.
6
5
Share

Why is the car wiper not spraying water?

Reasons why the car wiper does not spray water: 1. Pipe blockage. 2. The windshield washer fluid container has too little water or is empty. Introduction to car wipers: 1. Car wipers, also known as windshield wipers, water wipers, or windshield wipers, are devices used to wipe away raindrops and dust attached to the vehicle's windshield, improving the driver's visibility and increasing driving safety. 2. There are roughly two types of wipers: one is the traditional intermittent type, which is the most common wiper, with three to four segments, adjusted by the driver according to the rain and visibility conditions; the other is the rain-sensing type, mostly used in mid-to-high-end models.
10
0
Share

How to Reset the CRV Tire Pressure Light

Here are the steps to reset the Honda CRV tire pressure light: 1. Start the car and press the CAR button after the central display lights up; 2. Select the tire settings option in the vehicle settings menu and click the SET button; 3. When the screen displays whether the tire pressure of all four tires matches the required values, click confirm, and then the tire pressure monitoring initialization will be displayed to complete the process. Below is additional information about tire pressure: Tire pressure, strictly speaking, refers to the air pressure inside the tire. In terms of car maintenance, the engine is the heart of the car, and its damage will lead to the end of the car's life. Similarly, tire pressure is the blood pressure of the car, and the level of tire pressure plays a crucial role in the performance and power of the vehicle.
11
0
Share

How to Start and Stop an Automatic Transmission Car?

Starting and stopping methods for automatic transmission cars: 1. Correct starting procedure: Press the brake - Ignition - Shift to D gear (or R gear) - Release the handbrake - Release the foot brake - Press the accelerator - Start moving. 2. Correct stopping procedure: Press the brake - Engage the handbrake - Shift to P gear - Turn off the engine. 3. When stopping, you must wait until the vehicle comes to a complete stop before shifting to P gear, otherwise it may damage the transmission. Correct practices for starting and stopping on slopes: 1. On a slope, shifting directly to P gear can impact the transmission. The correct method is: Shift to N gear, engage the handbrake, press the brake, then shift to P gear. 2. For starting on a slope to prevent rolling back: Shift to D gear to start, then release the handbrake.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.