What's the matter with the Audi ignition latch failure?

1 Answers
LucilleLee
07/30/25 10:20am
The vehicle's instrument panel displays a fault in the ignition latch and the steering lock system. Fault diagnosis: Using the ODIS diagnostic tool to read the fault code 0046, the comfort system central module 393 records the fault: entry or start authorization switch unreliable signal. Entering diagnostic inquiry, J393's E415 terminal 15 is short-circuited to ground. According to the diagnosis, continue to check, prompting to measure whether the grounding wire of 393 and E415 is normal. After measurement, the grounding wire is 0.3Ω, which is normal. Fault resolution: Clear the sunroof drainage pipe, clean the connector with alcohol, reinstall it cleanly, and the fault disappears. During routine maintenance, it is essential to regularly check the sunroof drainage pipe.
Was this review help?
15
0
Share
More Forum Discussions

How to Replace the Timing Belt on a Sonata?

Align the mark on the camshaft timing gear with the mark on the valve cover, and align the mark on the crankshaft timing gear with the mark on the front cover. Install the timing belt in sequence onto the crankshaft timing gear, water pump pulley, idler pulley, camshaft timing gear, and tensioner pulley. Compress the automatic tensioner pushrod to the lowest position, insert a steel pin into the hole, and adjust the pulley using a snap ring pliers. Rotate counterclockwise until the two adjustment holes on the pulley are parallel to the ground, tighten the fixing bolt, and remove the steel pin. Rotate the crankshaft clockwise two full turns and check if the timing marks are correctly aligned.
5
4
Share

How to Adjust Valve Clearance in Diesel Engines?

Rotate the crankshaft and observe the movement of the valves in cylinder 4. When the intake and exhaust valves exhibit overlapping movement, this indicates the exhaust top dead center (TDC) of cylinder 4. At this point, cylinder 1 is at its compression top dead center. You can then adjust the intake and exhaust valves of cylinder 1, the intake valve of cylinder 2, and the exhaust valve of cylinder 3, as these valves are completely closed. Next, rotate the crankshaft 360 degrees, locate the compression top dead center of cylinder 4 using the same method, and adjust the remaining valves accordingly.
19
4
Share

Is NIO a Hybrid Vehicle?

NIO does not have any hybrid models in its lineup; all its vehicles are purely electric. Introduction to NIO: NIO is a global intelligent electric vehicle brand, established in November 2014. Its main products include the NIO ES6, NIO ES8, NIO EC6, NIO EVE, and NIO EP9. NIO is committed to providing high-performance intelligent electric vehicles and an exceptional user experience, aiming to create a joyful lifestyle for its customers. Introduction to NIO's Brand Logo: The name NIO is derived from "A New Day." "NIO" expresses the brand's vision of pursuing a better tomorrow and blue skies, as well as creating a joyful lifestyle for its users. The new logo consists of a sky symbolizing openness and the future, and a road symbolizing action and progress, embodying NIO's brand philosophy.
14
5
Share

What does brz mean?

brz is a noun referring to the new model of Subaru sports car. Introduction to Subaru BRZ: The Subaru BRZ was officially launched in 2015. The new car features a more sporty exterior design, equipped with 225/40ZR18 Michelin Pilot-Super-Sport series tires, reinforced chassis, and continues to be powered by a 2.0L naturally aspirated direct injection engine. Basic design of Subaru BRZ: The car adopts a horizontally opposed engine and front-engine rear-wheel drive layout. The suspension consists of front MacPherson independent suspension and rear double-wishbone suspension. It has a wheelbase of 2570mm, length of 4239mm, width of 1775mm, and height of 1285mm.
9
1
Share

Can OnStar Be Used in Volkswagen Cars?

OnStar system cannot be used in Volkswagen cars, as the OnStar system is a proprietary system of General Motors. Relevant usage regulations of the OnStar system: In China, General Motors has officially announced the service fees for the OnStar system to users, but it has not yet clearly stated whether non-GM car owners in China can purchase the OnStar system like a commodity. Nowadays, more and more car manufacturers are increasing their efforts in the research and development of interactive intelligent navigation systems, and many products have already been launched. Functions of the OnStar system: The functions of the OnStar system have expanded from the initial technologies such as digital crash signals, hands-free calling, on-demand diagnostic screening, situational information awareness, uninterrupted digital virtual reality technology, emergency assistance, and turn-by-turn navigation, to include new technologies such as emergency response data utilization, monthly diagnostic emails, crisis route selection, and multiple embedded languages.
20
1
Share

What is the mileage for Lynk & Co's first maintenance?

Lynk & Co's first maintenance is at 10,000 kilometers. The purpose of the first maintenance: The first maintenance is mainly to replace the engine run-in oil from the factory and the oil filter, and to check the tightness of the chassis screws. Maintenance required before reaching the first maintenance: There are two indicators for car maintenance cycles, one is a time indicator and the other is a mileage indicator, whichever comes first. Owners should try to perform maintenance before reaching the first maintenance cycle to avoid affecting the normal use of the car. Precautions for the first car maintenance: The first car maintenance mainly involves replacing the engine oil and oil filter. One important thing to note is that when changing the engine oil, the oil filter must also be replaced simultaneously. If the oil filter is not replaced, the new oil will be contaminated by the old filter.
15
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.