What's the matter with the abnormal charging system of BMW?

1 Answers
LeJessica
07/30/25 7:58am
The abnormal charging of BMW may be caused by: battery leakage, unreliable connection of the charging circuit, or charger damage. The specific information is as follows: 1. Battery leakage: Poor sealing between the upper cover and the bottom tank or cracking of the sealing glue due to collision may cause leakage; acid leakage from the cap valve; acid leakage from the terminal; acid leakage from other parts. 2. Inspection and handling of faults: First, conduct an appearance inspection to find the acid leakage part. Remove the cover to see if there is any trace of acid leakage around the cap valve, and then open the cap valve to observe whether there is flowing electrolyte inside the battery. After completing the above work, if no abnormality is found, a tightness test should be performed (inflate and pressurize in water, observe whether the battery produces and emits bubbles, bubbles indicate acid leakage). Finally, during the charging process, observe whether there is flowing electrolyte produced. If there is, it indicates a production reason. If there is flowing electrolyte during the charging process, it should be drained completely.
Was this review help?
4
5
Share
More Forum Discussions

What are the reasons for the car not moving when the gear is engaged?

The reasons for the car not moving when the gear is engaged are as follows: Automatic transmission oil pan leakage: The fault lies in the input shaft, planetary gear set, or output shaft of the automatic transmission. The automatic transmission should be disassembled for inspection. Loose connection between the gear lever and manual valve rocker arm: Check the linkage or cable between the automatic transmission gear lever and the manual valve rocker arm for any looseness. If there is looseness, it should be reinstalled and the position of the gear lever should be readjusted. Oil pump inlet filter screen clogged: Open the oil pan and check if the oil pump inlet filter screen is clogged. If there is no clogging, it indicates that the oil pump is damaged or there is a serious leakage in the main oil circuit. The automatic transmission should be disassembled for repair.
11
3
Share

What to Bring for Driving Test Part 3?

For Driving Test Part 3, you need to bring a valid ID card, your driving record file, and the successful appointment confirmation. At the test center, you will undergo magnetic ID card verification and fingerprint authentication before being allowed to take the test. Here are some important notes about the Driving Test Part 3: Regarding fingerprint verification: If a candidate fails the fingerprint verification, they must exit the vehicle to re-register their fingerprints before rejoining the queue for the test. Retaking the test if failing: If a candidate's score falls below the passing mark during the test, the system will automatically prompt them to pull over. After completing the pull-over maneuver, the system will initiate the next test attempt. Post-test instructions: After completing all required test items and driving more than 3 kilometers, the system will automatically prompt the candidate to pull over. Upon hearing the pull-over instruction, the candidate should choose a clear curb (or solid road edge line) along the test route and complete the pull-over maneuver safely. The system will then announce the test results.
15
0
Share

When driving, should you press the clutch or the brake to slow down?

When driving and needing to slow down, first gently press the brake to reduce speed, then press the clutch when the engine RPM drops below 1000 to prevent the car from stalling. Here is relevant information about slowing down: Emergency braking: In emergency situations where the vehicle needs to stop in the shortest distance and fastest time possible, don't consider engine braking or other unnecessary actions. Simply press both the clutch and brake pedals fully to the floor. This cuts off all engine power while allowing the vehicle's ESP and ABS systems to make the wheels move in a semi-rolling, semi-sliding state, maximizing traction to bring the vehicle to a stop. Slowing down at 0km/h or very low speeds: You can directly press the clutch and use the brake to slow down. At low speeds, the gear is also low, and the engine's traction force is relatively strong. Therefore, pressing the clutch cuts off the power; if you don't disengage the clutch while slowing down, it might cause the engine to stall.
5
4
Share

What are the high-end car brands from South Korea?

South Korea's high-end car brands are Hyundai and Kia. Below are the introductions of three high-end models: Kia K9, Hyundai Equus, and Hyundai Genesis: Kia K9: The body dimensions are 5095/1900/1490mm in length, width, and height respectively, with a wheelbase of 3045mm. The Kia K9 available in the domestic market is equipped with a 3.8L V6 direct injection engine, delivering a maximum power of 246kW and a peak torque of 395N·m. Hyundai Equus: The body dimensions are 5160/1890/1495mm in length, width, and height respectively, with a wheelbase of 3045mm. The extended version has a wheelbase of 3345mm. In terms of power, there are two engine options available for consumers: 3.8L and 5.0L. Hyundai Genesis: Compared to the premium German brands, the price of Genesis is actually quite competitive. It comes with a 3.0L naturally aspirated V6 engine, Hyundai's self-developed 8AT, an electronically controlled four-wheel drive system, and more.
1
2
Share

Where is the Teana water temperature gauge?

The Teana water temperature gauge is located on the left side of the speedometer. The engine water temperature gauge is used to indicate the temperature of the engine coolant. The coolant temperature signal is provided by the engine coolant temperature sensor installed on the engine cylinder head. When the engine is operating normally, the displayed value should be between 80-100°C. If the engine coolant temperature reaches or exceeds 112°C, the coolant temperature warning light will illuminate. At this point, you should immediately stop the vehicle and turn off the engine, then check the coolant level and cooling system pipes!!
7
0
Share

What Causes the Striped Marks on Power Window Glass?

Power window glass may develop striped marks due to sharp objects in the window regulator scratching the glass during operation or external force impacts. Here are solutions for addressing scratches on power window glass: Perform Glass Scratch Repair: Use automotive glass repair kits to treat cracks or minor damage. This process is time-efficient and won't affect daily vehicle use, as it primarily involves filling cracks with liquid resin to seal the gaps. Remove Sharp Objects from Window Regulator: If the glass damage is caused by foreign objects in the regulator, the owner or a professional should promptly remove these sharp objects from the window regulator.
10
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.