What's the matter with no reversing camera?

How Often Should the Battery of Trumpchi GS4 Be Replaced?

The original battery of a new Trumpchi GS4 is recommended to be replaced every three years or more. If it is not the original battery of a new car, it is suggested to replace it every two to three years. When the battery has been in use for about two and a half years, regular maintenance should include battery testing to prevent potential issues. Here are some precautions regarding the battery: 1. Avoid parking the car in an open parking lot for extended periods. If long-term parking is necessary, remove the battery to prevent freezing damage. 2. In winter, the car engine may be harder to start. Each attempt to start the engine should not exceed 5 seconds, with an interval of at least 15 seconds between attempts. 3. The car battery should be charged regularly. If left unused for a long time, the battery will gradually discharge on its own until it becomes unusable. Therefore, the car should be started periodically to charge the battery. 4. Clean the battery terminals regularly and apply special grease to protect the wiring harness. Frequently check the battery accessories and connection lines.

19

2

Share

What are the reasons for the lack of power when stepping on the accelerator in Haval H6?

The main reasons for the lack of power when stepping on the accelerator in Haval H6 are as follows: 1. Carbon deposit issues. 2. Fuel system problems. 3. Intake system problems. 4. Clogged fuel injectors. 5. Fuel pipe leakage. 6. Reduced fuel pump power, clogged fuel filter, etc. Below is an introduction about the Haval H6: The Haval H6 uses two engines across its lineup, one being a 1.5-liter turbocharged engine and the other a 2.0-liter turbocharged engine. The 1.5-liter turbocharged engine has a maximum power of 169 horsepower and a maximum torque of 285 Nm, with the maximum power speed ranging from 5000 to 5600 rpm and the maximum torque speed ranging from 1400 to 3000 rpm. The 2.0-liter turbocharged engine has a maximum power of 224 horsepower and a maximum torque of 385 Nm, with the maximum power speed at 5500 rpm and the maximum torque speed ranging from 1600 to 3600 rpm.

20

3

Share

How to Reset the Maintenance Light on the Borui?

Resetting the maintenance light is an essential operation after car maintenance. The function of the maintenance light is to record the mileage of some important components, serving as a reminder for both the car owner and the maintenance staff. If the maintenance light comes on, it indicates that the car needs maintenance. Below are the operation steps: 1. With the car turned off, press and hold the short-distance counter reset button below the tachometer without releasing it. 2. Turn the ignition switch to the ON position, then release the short-distance counter reset button. At this time, the SERVICE sign will appear on the display. 3. Pull out the minute button on the clock and turn it to the right. The mileage will be displayed on the screen. 4. Turn off the engine. 5. Turn the ignition switch to the ON position again, and the SERVICE sign will disappear.

3

0

Share

Location of the Haval H2 Air Conditioning Filter

Haval H2's air conditioning filter is located inside the glove compartment in front of the passenger seat. The air conditioning filter should be replaced approximately every 5,000 kilometers to prevent issues such as the car's air conditioner failing to cool or heat, or producing odors due to clogging. Below are the replacement steps: 1. Open the glove compartment in front of the passenger seat and remove any items inside. 2. After clearing the items, pinch the limit blocks on both sides of the glove compartment and remove it. 3. Press the plastic clip above the air conditioning filter box and remove the filter box from the glove compartment. 4. Replace the old air conditioning filter with a new one inside the filter box. 5. Reassemble the glove compartment in the reverse order of disassembly.

11

0

Share

Should the 2010 Buick LaCrosse use 92 or 95 octane gasoline?

According to the official vehicle manual recommendation, the 2010 Buick LaCrosse should use 92 octane gasoline. For the 2010 Buick LaCrosse, besides checking the appropriate gasoline grade in the vehicle manual, you can also find this information on the fuel tank cap, which will be clearly marked. Typically, the gasoline grade can also be determined based on the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should use 92 octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95 octane gasoline. However, with the application of some new technologies, the gasoline grade cannot be solely determined by the compression ratio. Engines with high compression ratios can also be tuned to use lower octane gasoline because, besides the compression ratio, other factors such as ignition timing, turbocharging technology, and Atkinson cycle technology also play a role. Generally, the higher the gasoline octane number, the higher the octane rating and the better the anti-knock performance. 92 octane gasoline contains 92% isooctane and 8% n-heptane, while 95 octane gasoline contains 95% isooctane and 5% n-heptane. If the 2010 Buick LaCrosse occasionally uses the wrong gasoline grade, simply switch back to the correct grade after use. However, prolonged use of the wrong gasoline grade can have the following effects: For vehicles recommended to use lower octane gasoline, using higher octane gasoline will not cause damage, but the increase in octane rating will alter the fuel's ignition point, leading to delayed combustion in the engine. This means the engine's power output and thermal efficiency will decrease, resulting in a noticeable drop in performance. For vehicles recommended to use higher octane gasoline, using lower octane gasoline can cause engine knocking. Because the octane rating is too low, the reduced ignition point may cause the gasoline to ignite prematurely during the compression stroke. If the fuel ignites before the spark plug fires during the compression stroke, resistance will occur during the upward stroke. This resistance can make the engine run very unevenly. If the knocking is mild, it may only increase noise without significant engine damage. However, if the knocking is severe, it indicates serious engine conditions, affecting not only driving stability but also causing abnormal wear on pistons and cylinders, and in severe cases, even cylinder scoring.

8

1

Share

Operation Method of Touareg Chassis Lifting System

The function of the automobile chassis is to support and install the engine, some electrical equipment and accessories, forming the overall shape of the vehicle. The Touareg chassis is equipped with an active four-wheel air suspension system that supports all-terrain and all-weather operation, minimizing the impact of external temperature and air pressure fluctuations (such as in high-altitude areas). In daily driving, drivers may need to adjust the chassis height. Below are the operation methods for the Touareg chassis lifting system: 1. First, locate the chassis height control switch in the central console area of the cockpit. 2. Press the one-touch start switch in the central console to power on the vehicle; otherwise, chassis height adjustment will be unavailable. 3. Rotate the knob behind the gearshift to raise or lower the chassis.

19

5

Share

What's the matter with no reversing camera?

How Often Should the Battery of Trumpchi GS4 Be Replaced?

What are the reasons for the lack of power when stepping on the accelerator in Haval H6?

How to Reset the Maintenance Light on the Borui?

Location of the Haval H2 Air Conditioning Filter

Should the 2010 Buick LaCrosse use 92 or 95 octane gasoline?

Operation Method of Touareg Chassis Lifting System

Does the Tiguan L Have a Particulate Filter?

What Are the Principles and Techniques of Reversing a Car?

What Are the Effects of Running the Car Air Conditioning for a Long Time?

What is the engine displacement of the Audi S6?