What Restrictions Do Not Apply to Sweeper Vehicles?

1 Answers
MacElla
07/30/25 1:39am
Road maintenance vehicles and engineering operation vehicles are not restricted by traffic signs and markings in terms of their driving routes and directions while performing tasks, provided that they do not affect the passage of other vehicles. Passing vehicles and pedestrians should yield the right of way. Water sprinklers, sweeper vehicles, and other motor vehicles should operate according to safety standards; they are not restricted by lane division regulations when not affecting other vehicles' passage, but they must not drive in the opposite direction. Fire Hazard Precautions: When maintaining road sweeper vehicles, flammable materials such as oils and cleaning agents are often used. It is essential to follow standard operating procedures and implement fire prevention measures, keeping a fire extinguisher on hand to prevent fires. Do not smoke or ignite flames near the fuel tank or battery, as flammable gases from the fuel tank and hydrogen from the battery can easily catch fire. Burn Hazard Precautions: After the vehicle has been in use for some time, components such as the radiator, exhaust pipes, power steering fluid reservoir, and spark plugs can become very hot. Avoid contact to prevent burns. Mechanical Injury Precautions: Before starting the vehicle, check the initial gear position to avoid collisions caused by excessive starting speed. When working under the engine hood, clear the cab to prevent accidental injury from sudden engine movement or others' operational errors. Avoid Damaging the Sweeper Vehicle: Take care not to damage the road sweeper vehicle, especially to prevent brake fluid leakage. Brake fluid can damage the vehicle's paint film and, if accidentally splashed into the eyes, can impair vision or even cause blindness. In case of accidental exposure, rinse immediately with clean water.
Was this review help?
6
3
Share
More Forum Discussions

What does the AC switch in a car mean?

Car AC switch is the cooling on/off button for the vehicle's air conditioning system. When pressed, the air conditioning compressor will operate. Below is relevant information about the automotive air conditioning system: 1. After turning on the AC switch, the vehicle's computer receives the signal from the AC switch, and then sends a signal to the air conditioning compressor. 2. Press the AC button and rotate the temperature selection switch to the blue section, then cold air will blow out from the car's air conditioning. 3. Essentially, the AC button controls whether the compressor operates. Inside the compressor, there is an electromagnetically controlled clutch. When its coil is energized, the electromagnetic clutch engages and the compressor works. Otherwise, the compressor's pulley just spins idly without the compressor actually operating.
20
2
Share

What to Do If the Vehicle Still Fails to Start After a Jump Start?

What to Do If the Vehicle Still Fails to Start After a Jump Start: 1. If the car battery is dead, you can seek a jump start from another vehicle. Before jump-starting, ensure all electrical devices in the dead vehicle are turned off to avoid accidentally reversing the battery terminals, which could cause a short circuit and damage the vehicle's electronic components. 2. If the car still fails to start after a jump start, the issue might be with the jumper cables being too thin. When purchasing jumper cables, always opt for genuine, quality-assured ones, preferably thicker with an outer diameter of at least 10mm. 3. Another possible reason for the vehicle not starting after a jump start is insufficient charging time. Generally, after jump-starting, let the rescue vehicle run for a while—wait about 5-10 minutes before attempting to start the dead vehicle. If it starts, keep the previously dead vehicle running for about 30 minutes to allow the alternator to recharge the battery. 4. If the vehicle still won't start, the issue might be with the engine, requiring inspection and repair at a service center or 4S shop. 5. If the battery has been used for an extended period, sulfation may occur. If the sulfation is mild, recharge the battery with a low current for at least 12 hours. For severe sulfation, replace the electrolyte before recharging.
15
5
Share

What Documents Should You Carry When Driving on the Road?

When driving on the road, you must carry a driver's license and a motor vehicle license. Both documents are indispensable. Here are the precautions for a new car on the road: 1. The permitted vehicle type on the driver's license must match the vehicle being driven. The annual review and other records on the driver's license must meet the requirements. 2. Carry a motor vehicle license that matches the license plate of the vehicle being driven. The motor vehicle license must not be lent, altered, or forged. 3. If necessary, you also need to carry the driver's ID card. 4. Insured vehicles must carry the insurance policy. 5. If driving a commercial vehicle, you also need to carry the professional qualification certificate for road transport personnel. 6. The vehicle license plate (or temporary license plate or replacement plate certificate) should be installed at the front and rear of the vehicle. The license plate should be appropriately and visibly positioned, with clear characters, and must match the vehicle type and number on the motor vehicle license. Expired or invalid temporary license plates must not be used. 7. Carry a valid road toll payment certificate or exemption certificate. The vehicle type, license plate, unit, and date on the certificate must be accurate.
13
5
Share

What are the symptoms of low coolant in a vehicle?

Driving with low coolant in a vehicle can leave the car engine and radiator unprotected. Insufficient coolant affects the radiator's heat dissipation efficiency, failing to achieve the necessary cooling effect. This disrupts the normal circulation of coolant, leading to overheating and, in severe cases, engine damage. In cold climates, it can also cause the engine or radiator to freeze, resulting in engine failure and rendering the vehicle inoperable. Methods to determine if coolant is low: Observe the coolant warning light on the dashboard. If it lights up, it is likely due to low coolant, though it could also be triggered by excessively high cylinder temperatures. Check the coolant reservoir. If the fluid level is below the minimum mark (MIN), do not continue driving; promptly add coolant. Inspect the water level markings on the coolant reservoir. The coolant level should normally be between the maximum and minimum marks. To check if coolant is low, observe the markings. If the coolant is below the minimum level, it indicates a deficiency.
12
4
Share

What Causes a Sudden Increase in Engine Noise?

Reasons for a sudden increase in engine noise: 1. Engine Mount Deterioration or Loosening: Engine mounts are rubber blocks placed between the engine and the vehicle frame. Their purpose is to reduce vibrations and absorb shocks during engine operation while securing the engine in place. If these mounts become worn or loose, the engine may vibrate, producing louder noises as the speed increases. 2. Improper Engine Oil Usage: If the oil viscosity is not suitable for the engine, it can lead to carbon buildup, causing increased engine noise. Oil with too low viscosity may result in insufficient lubrication, leading to wear on engine components and abnormal noises. Conversely, oil with too high viscosity can place excessive load on the engine, also generating noise. 3. Engine Misfire: An engine misfire occurs when one or more cylinders fail to function properly. Common symptoms include intermittent exhaust gas flow and noticeable shaking of the exhaust pipe, accompanied by distinct "popping" or "thumping" sounds from the engine. 4. Cold Start: During a cold start, the engine's lubrication is less effective due to the oil being thicker and less fluid. This can cause mechanical wear noises. Additionally, the coolant temperature is low, and the air-fuel mixture is richer, leading to incomplete combustion, which may cause the engine to vibrate and produce noise. 5. Timing Gear Noise: Over time, timing gears may experience excessive wear due to improper gear clearance adjustment or hardened belts. In severe cases, gear teeth may wear down, causing loose meshing between gears. This can result in a "clattering" noise during engine operation. 6. Exhaust Pipe Leak: If there is a leak in the intake or exhaust system, gases may escape during engine startup, causing vibrations and noise.
13
4
Share

How often should the vehicle's antifreeze be replaced?

The vehicle's antifreeze should be replaced every two years. This is just a reference interval. For commercial vehicles with higher mileage, the replacement interval should be shorter. Since driving conditions vary for each vehicle, the replacement should be based on actual usage. Check the antifreeze condition regularly - if the level is low, replenish it promptly; if suspended particles, sediment, or discoloration/degradation are observed, replace the antifreeze immediately and flush the system. Antifreeze replacement procedure: Before a complete antifreeze replacement, conduct a thorough inspection for any leaks or cracks in the pipelines, with special attention to the five-way hose (named for its five connection points to different components). Antifreeze circulates through this hose before being distributed to various parts of the vehicle. If any antifreeze leakage is detected at this component, replace the hose or reseal the connections as needed. Drain the old antifreeze, then flush the channels with clean water. Add water to the antifreeze reservoir and continue filling until clean water circulates continuously through the engine cooling system. Start the engine and let it idle for 3-5 minutes to circulate the water. Initially, slightly pinkish water will flow out - continue flushing until completely clear water emerges. Remember to disconnect the heater hose and drain all water from the heater core. Approximately one hour after draining, pour new antifreeze into the radiator hose for rapid filling. Then add another container of antifreeze to the reservoir until nearly full. Run the engine for about 10 minutes - as air escapes from the cooling system, the fluid level will drop. Top up the antifreeze to the "MAXT" mark on the reservoir.
14
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.