What procedures are required to switch from C1 to C2 after passing Subject 1?

What is the speed limit on the Ningjingyan Expressway?

Ningjingyan Expressway has a speed limit of 100 km/h. Maximum speed: Expressways should indicate the driving speed of lanes. The maximum speed shall not exceed 120 km/h, and the minimum speed shall not be lower than 60 km/h. On expressways, the maximum speed for small passenger vehicles shall not exceed 120 km/h, for other motor vehicles shall not exceed 100 km/h, and for motorcycles shall not exceed 80 km/h. Minimum speed: According to the "Regulations for the Implementation of the Road Traffic Safety Law," when there are 2 lanes in the same direction, the minimum speed for the left lane is 100 km/h; when there are 3 or more lanes in the same direction, the minimum speed for the far-left lane is 110 km/h, and the minimum speed for the middle lane is 90 km/h. If the speed indicated by road speed limit signs is inconsistent with the above lane speed regulations, the speed indicated by the road speed limit signs shall be followed.

17

3

Share

Is it serious if the car didn't stall when driving through water?

There is basically no impact. Here are the relevant introductions about vehicle wading: 1. Introduction to vehicle wading: As the name suggests, vehicle wading refers to driving on low-lying, waterlogged roads, passing through water. It usually occurs in rainy weather, where poor drainage equipment leads to water accumulation in low-lying road sections. 2. Precautions for vehicle wading: Before wading, pay attention to observing the road conditions; while in water, maintain stable power; after wading, check the electrical system. If the car breaks down in water, the main reason is water entering the exhaust pipe, and in some cases, there may also be electrical damage. Once the car breaks down, do not attempt to start it again, as this may cause water to enter the intake tract and damage the valves, and in severe cases, may lead to engine failure. Instead, the car should be immediately towed to a 4S shop and handed over to professionals for handling.

11

4

Share

Where is the specific location of the car light switch?

For small cars, the light switch is typically located on the control lever beneath the steering wheel, usually on the left side. You can toggle the lights by pulling or pushing the lever. Below is relevant information about car lights: 1. Headlights: The combination headlights are positioned at the front of the vehicle, primarily serving illumination and signaling purposes. They illuminate the road ahead, enabling safe driving at night. Based on their light source, combination headlights can be categorized into halogen lamps and xenon lamps. 2. Taillights: The combination taillights are located at the rear of the vehicle, mainly functioning for illumination and signaling. Taillights generally consist of rear position lights, reverse lights, brake lights, rear fog lights, turn signals, and reflectors.

17

1

Share

What are the reasons for the fuel pump not working?

Reasons for the car fuel pump not working: Oil contamination is the direct cause of the fuel pump not working. Solution: Strictly follow the manufacturer's recommended fuel grade, ensure the car is never out of fuel as a basic measure, and regularly maintain the fuel tank to clean out impurities. Improper refueling behavior may cause the fuel pump to stop working. Solution: Always follow standard refueling procedures and refuel at reputable gas stations. Driving with low fuel levels for extended periods can prevent the fuel pump from cooling, leading to poor oil quality, excessive impurities, frequent pump blockages, and abnormal driving. Solution: When refueling, try not to wait until the fuel warning light comes on, as this shortens the pump's lifespan. Too little fuel or running out of fuel can cause the pump to malfunction. The fuel pump plunger spring may fail or break. Solution: Replace with a new spring. Incorrect adjustment of component positions. Solution: Reposition or polish the wheel body. If the pump body is cracked, replace the fuel pump immediately.

19

2

Share

How many kilometers should the transmission oil of the Magotan B8 be replaced?

The following is a detailed introduction to the replacement time of the Magotan B8 transmission oil: 1. The maintenance manual of the Magotan B8 clearly states that it should be replaced every 100,000 kilometers. 2. The replacement interval can be appropriately shortened based on driving conditions (recommended replacement every 60,000 kilometers). 3. If the car is driven very little, the replacement should not exceed 3 years. Below are additional notes on maintaining the transmission oil: 1. The maintenance of the transmission oil mainly involves combining it with the primary maintenance of the car, draining accumulated water and sediment from the transmission, and checking for oil leakage at the joints and switches of the oil pipes. 2. For the fuel tank cap equipped with an air valve and steam valve, check whether the vent hole is clear. 3. The filter screen at the fuel filler port should be kept intact to prevent impurities from entering the fuel tank during refueling and clogging the oil circuit. The sealing gasket of the fuel filler cap should also be intact to prevent oil from overflowing during driving.

19

2

Share

What Are the Specifications and Models of Oil Seals?

Here is an introduction to the specifications and models of oil seals: 1. Parameters: The main parameters of skeleton oil seal specifications include inner diameter, outer diameter, and height. 2. Composition: The unit is mm; the main material is nitrile rubber. The diameter of the inner circle is called the inner diameter; the outer edge diameter of the pipe or container, including wall thickness; the distance from the bottom to the top of the skeleton oil seal. Below is additional information on the topic: 1. Function of oil seals: Generally, oil seals refer to skeleton oil seals. The function of an oil seal is to isolate the components that need lubrication in the transmission parts from the output parts, preventing the leakage of lubricating oil. The skeleton acts like the reinforcement in concrete structures, providing strength and helping the oil seal maintain its shape and tension. 2. Classification: According to structural form, they can be divided into single-lip skeleton oil seals and double-lip skeleton oil seals. The secondary lip of a double-lip skeleton oil seal serves as a dust seal, preventing external dust, impurities, etc., from entering the machine. Based on skeleton type, they can be categorized into internally wrapped skeleton oil seals, externally exposed skeleton oil seals, and assembled oil seals. According to working conditions, they can be classified into rotary skeleton oil seals and reciprocating skeleton oil seals.

4

3

Share

What procedures are required to switch from C1 to C2 after passing Subject 1?

What is the speed limit on the Ningjingyan Expressway?

Is it serious if the car didn't stall when driving through water?

Where is the specific location of the car light switch?

What are the reasons for the fuel pump not working?

How many kilometers should the transmission oil of the Magotan B8 be replaced?

What Are the Specifications and Models of Oil Seals?

How long does it take to slow charge the Leapmotor T03?

What causes white smoke from diesel engine exhaust?

What does engine 2.5g mean?

What are the symptoms of a damaged timing sprocket?