What procedures are required for transferring driving school records?

1 Answers
Zara
07/29/25 11:45pm
The procedures required for transferring driving school records are as follows: 1. Transfer certificate: The student must obtain a transfer certificate from the original driving school. 2. Personal records: Then go to the vehicle management office or driving school to retrieve personal records. 3. Enrollment at new driving school: Report to the new driving school with the records and transfer certificate. Please note the relevant regulations: 1. Personal signature: The applicant must come in person to handle the procedures and sign on the spot, and cannot authorize others to act as an agent. 2. Identity proof: "Resident ID card"; non-locals also need to provide a local temporary residence permit. 3. Driving license application: If fraudulent or bribery methods are used to obtain a motor vehicle driving license in another place, the transferred license will be revoked, and the applicant will not be allowed to apply for a motor vehicle driving license again within three years.
Was this review help?
17
3
Share
More Forum Discussions

How to Turn on the High Beam on a BMW?

To activate the high beam on a BMW: When the low beam is on, push the lever forward once to switch to high beam, and pull it back to return to low beam. The high beam is one of the essential functions in a car. Compared to the low beam, the high beam emits parallel light with concentrated and brighter illumination, allowing it to reach higher and farther objects, significantly aiding the driver's visibility at night. However, vehicles with high beams activated should switch to low beams at least 150 meters before encountering oncoming traffic. BMW's lineup includes models such as the BMW 3 Series, BMW 7 Series, BMW X5, BMW X1, and BMW 1 Series. Taking the BMW 3 Series as an example, its body dimensions are 4719mm in length, 1827mm in width, and 1459mm in height, with a wheelbase of 2851mm, a fuel tank capacity of 59 liters, and tire specifications of 225/45R18.
10
3
Share

How Long Does It Take to Charge a BYD Song?

When charging the BYD Song, it takes a considerable amount of time to preheat the battery (to reach the set value) before entering the normal charging state. Using a household 220-volt power supply, a full charge takes approximately 9 hours at around 15 degrees. At a professional charging station, it takes between 15 minutes to half an hour. Here is more information about the BYD Song: 1. Exterior: The BYD Song features an X-shaped front grille, giving it a sporty appearance. The side profile incorporates hidden A/B/C pillars, creating a floating roof visual effect. 2. Powertrain: The BYD Song is equipped with a hybrid system consisting of a 1.5T engine and two electric motors, with one motor positioned at the front axle and the other at the rear axle, enabling all-wheel drive functionality. Additionally, the BYD Song has a pure electric range of 70km and can accelerate from 0-100km/h in 4.9 seconds.
2
0
Share

Should the Tensioner Pulley Be Replaced if It Makes Noise?

The tensioner pulley should be replaced as soon as possible if it makes noise. Here is some information about the tensioner pulley: 1. The tensioner pulley mainly consists of a fixed housing, tensioning arm, pulley body, torsion spring, rolling bearing, and spring bushing. It can automatically adjust the tension according to the tightness of the belt, ensuring the stability, safety, and reliability of the transmission system. 2. The tensioner pulley is a wear-prone component in automotive parts. Over time, the belt may stretch, and some tensioner pulleys can automatically adjust the belt tension. Additionally, the tensioner pulley makes the belt run more smoothly, reduces noise, and prevents slippage. 3. The function of the tensioner pulley is to adjust the tightness of the timing belt. It is generally replaced together with the timing belt to avoid future issues. Other parts do not need to be replaced as long as regular maintenance is performed.
12
2
Share

What does maxac and ac air conditioning mean?

maxac is the maximum cooling mode of the air conditioning, and ac is the switch for the car air conditioning cooling mode. Once turned on, the air conditioning can cool. Below are the relevant explanations: 1. The cooling principle of car air conditioning is that after pressing the ac button, the compressor clutch will engage, and the engine will drive the compressor to operate. The compressor continuously compresses the refrigerant and delivers it to the evaporator. The refrigerant can cool the evaporator, and the evaporator can cool the air blown by the blower, so the air conditioning vents can blow out cold air. 2. The heating principle of the air conditioning is that when the heating function is turned on, there is no need to press the ac button, and the compressor does not need to operate when using the heating. When the air conditioning is heating, the high-temperature coolant from the engine flows through the heater core, and then the air blown by the blower passes through the heater core, so the air conditioning vents can blow out warm air.
7
4
Share

Does the 4S warranty cover scratches on a new car?

Scratches on a new car are not covered by the 4S warranty because they are caused by human factors and are not related to vehicle quality issues, thus falling outside the warranty scope. However, you can file an insurance claim, have the assessor evaluate the damage, and then proceed with repairs. This helps avoid unnecessary repair costs that may not be reimbursable. Precautions for using a new car include: 1. Warm up the engine before starting; 2. Change the gear oil after driving 2,000 kilometers and pay attention to vehicle maintenance; 3. Control the engine speed during the break-in period to prevent damage from excessive RPM; 4. Get comprehensive insurance and install a dashcam to avoid unnecessary disputes and losses; 5. Avoid sudden acceleration or deceleration to prevent damage to vehicle components.
14
1
Share

What is the usage method of fuel injector cleaner?

The usage method of fuel injector cleaner is: 1. Start the engine and warm it up until the cooling fan activates, then turn off the engine; 2. Locate the engine's fuel inlet and return pipes, disconnect the inlet pipe, and block the return pipe; 3. Remove the vacuum hose at the top of the fuel pressure regulator and install the pressure cleaning tank; 4. Use connecting hoses and transition joints to link the special fuel with the main fuel supply pipe, and disconnect the original vehicle's electric fuel pump power circuit; 5. Turn on the ignition switch, start the engine, and let it run until the fuel injector cleaner is completely consumed and the engine automatically shuts off (this process takes about 10 minutes), completing the cleaning of all fuel injectors; 6. Reverse the installation steps to remove the pressure cleaning tank, detached connectors, gauges, connecting pipes, reconnect the fuel inlet pipe and vacuum valve, reconnect the fuel pump circuit, and restore the vehicle's original fuel supply state.
2
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.