···
Log in / Register

What procedures are required for licensing a used car?

1 Answers
DeDelilah
07/28/25 2:18pm

Licensing a used car requires the new owner's ID card, compulsory traffic insurance policy, "Motor Vehicle Registration Certificate", etc. The following are the relevant procedures for used car transactions: 1. Conditions for used car renaming: vehicle registration certificate, vehicle license, ID cards of both buyer and seller. If it is a company vehicle, the company code certificate and official seal are required. In addition, the vehicle must be under normal annual inspection and without any violations to process the renaming and transfer. The original owner must be present in person to complete the procedures. 2. Used car transaction procedures: The required documents for a used car transaction include the vehicle registration certificate, vehicle license, purchase invoice, insurance policy, and ID cards of both parties involved in the transaction.

Was this review help?
10
4
Share
More Forum Discussions

What glue is best for bonding car bumpers?

Using AB glue is recommended for bonding car bumpers. The application method for AB glue is as follows: 1. At room temperature (25°C), clean the surfaces to be bonded. Then apply A glue and B glue in a 1:1 ratio by either overlapping application or applying A glue to one surface and B glue to the other before joining them together. Perform 2-3 alignment adjustments before fixing for 5-10 minutes. 2. At room temperature (25°C), clean the surfaces to be bonded. Then mix A glue and B glue in a 1:1 ratio using a plastic mixing sheet and apply to the bonding surfaces within 3 minutes. Fix for 5-10 minutes. 3. Note: Do not mix large quantities of glue at once during use, and ensure good ventilation. The glue contains acrylate odor - do not ingest.
13
4
Share

What are the reasons for the 4matic malfunction in Mercedes-Benz?

The main reasons for the four-wheel drive system being unusable can be categorized into three aspects. The specific reasons are introduced as follows: Related system control program malfunction: For example, transmission program failure or 4ETS system program failure. However, the most noteworthy issue here is the battery voltage problem. A damaged battery or low voltage can prevent certain programs from running, with 4matic being one of them. Power transmission distribution failure: For instance, damaged drive shaft, faulty ABS pump, or defective wheel speed sensor. The wheel speed sensor deserves special attention here. It is a crucial component of the ABS system and also the most common cause of malfunctions. Although it is not prone to breaking, it is susceptible to dirt accumulation, which can render it ineffective. Related data transmission failure: This requires a detailed inspection of the wiring and connectors between various systems and components.
5
5
Share

What is the Toyota model with 'Dragon' in its name?

Toyota's model with 'Dragon' in its name is the Toyota Avalon. As a brand that entered the Chinese market early, it has built a strong reputation among consumers. Dimensions: The Toyota Avalon measures 4975 mm in length, 1850 mm in width, and 1450 mm in height, with a wheelbase of 2870 mm. The Toyota Avalon is a mid-size sedan and is positioned in the same class as the Camry. Engine options: The Toyota Avalon is equipped with two engine options: a 2.0-liter naturally aspirated engine and a 2.5-liter naturally aspirated engine. Suspension system: The Toyota Avalon features a MacPherson strut front suspension and an E-type multi-link rear suspension.
8
4
Share

Why is the fuel consumption of the 2020 Hyundai Accent so high?

Possible reasons for high fuel consumption include unnecessary increase in vehicle load, frequent braking and starting, and driving at high speeds in low gears. The main factors affecting fuel consumption are as follows: Unnecessary increase in vehicle load: Many new car owners like to pile various decorations and exterior accessories onto their cars, and some even go as far as moving their office and home into the car. Blindly installing body kits, spoilers, winches, and roof racks will also increase the vehicle's fuel consumption. Frequent braking and starting: Apart from the car's design and engine factors, the real waste of fuel comes from the driving habits of the owner. Frequent sudden braking and sudden acceleration are the biggest causes of increased fuel consumption. There was once an experiment where the same car was driven by different drivers, and the fuel consumption measured when driven by a novice was twice as high as that of an experienced driver. This shows how important good driving habits are for saving fuel.
14
5
Share

What is the function of the door buttons on the Audi Q3?

Audi's main driver's door side button is an infrared anti-theft alarm, which is activated by turning on that switch. When the car is locked, if there is movement inside the vehicle, it will trigger an alarm, preventing accidental locking of children or pets inside the car. Vehicle Introduction: Audi is a world-renowned automobile developer and manufacturer. As a representative of high technical standards, quality benchmarks, innovation capabilities, and classic car models, Audi is one of the most successful car brands in the world. The main driver's door side button on an Audi is an infrared anti-theft alarm, which comes in two types: active and passive. Alarm System: An active infrared alarm emits infrared rays actively. When these rays encounter an obstacle, they bounce back and are received by the alarm's sensor.
7
3
Share

How long is the warranty period for the Audi A4L?

Effective from September 2, 2013, newly purchased Audi vehicles come with a return, replacement, and repair validity period of 2 years or 50,000 kilometers, whichever comes first. The warranty period is 3 years or 100,000 kilometers, whichever comes first. Circumstances where the three-guarantee service cannot be normally enjoyed: The purchased vehicle has been notified in writing of existing defects; damage caused by consumer's unauthorized modification, adjustment, or disassembly where the vehicle documents explicitly prohibit such actions; damage caused by improper handling by the consumer when quality issues arise; damage caused by the consumer's failure to use, maintain, or repair the product correctly as per the user manual; damage caused by force majeure; quality issues with consumable parts beyond the stated warranty period. Notes: During the three-guarantee validity period and warranty period, valid purchase invoice and three-guarantee certificate (the certificate date must match the purchase invoice date) must be provided to enjoy the corresponding three-guarantee services.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.