What procedures are required for converting a private car to natural gas?

1 Answers
SanGenevieve
07/29/25 11:42pm
After converting a private car to natural gas, you need to go to the vehicle management office to have a dual-fuel chapter stamped on the back of the driving license copy, to prove that the oil-to-gas conversion was done at a modification factory recognized by the vehicle management office. Here is some information about converting a car to natural gas: 1. Precautions: After converting a private car to natural gas, you need to pay attention to the heating system, especially in winter. When the temperature is too low, the rubber components inside the pressure reducer may become stiff, leading to improper operation and making the vehicle unable to run normally, with a high failure rate. Since most taxis have not cleaned the engine water channels, the heating for the natural gas pressure reducer may be insufficient. 2. Precautions: After the vehicle modification is completed, you should take the vehicle modification qualification certificate issued by the modification unit, along with the modification application form, to the vehicle management department to complete the motor vehicle alteration procedures. Generally, formal oil-to-gas conversion manufacturers will handle this procedure for vehicles converted at their factory.
Was this review help?
3
0
Share
More Forum Discussions

What is the reason for the constant flickering of the right reading light in the Golf 8?

Golf 8 right reading light flickering may be due to an issue with the dome light switch. It is recommended to use a computer to log into the circuit or check the switch. Below is some relevant information about the Golf 8: 1. Vehicle Positioning: The Golf 8 is a new generation Golf model (eighth generation) under FAW-Volkswagen, officially debuted at the 2020 (16th) Beijing Auto Show. 2. Powertrain: The Golf 8 is built on the MQB platform, equipped with a 1.4TSI engine, delivering a maximum power of 150Ps and a peak torque of 250Nm. 3. Body Dimensions: The Golf 8 measures 4296/1788/1471mm in length, width, and height respectively, with a wheelbase of 2631mm.
8
4
Share

What does the car lane change assist function mean?

Lane change assist can also be referred to as blind spot monitoring. The role of lane change assist: Its function is to alert the driver of approaching vehicles from behind through the side mirrors or other parts of the vehicle. Due to vehicle design, there are certain blind spots in the rear view when changing lanes or overtaking. The lane change assist system aims to minimize these blind spots, allowing the driver to assess the situation of vehicles behind through warning signals. Precautions: Lane change assist is ultimately just a reminder device and cannot help the driver complete the lane change action. The final judgment still relies on the driver's own observation. Technology serves people, and having safe driving awareness and good driving habits are the most crucial factors.
4
5
Share

What Happens When a Car Wheel Speed Sensor Fails?

It can cause deviations in the speed display. Below is a detailed introduction: Safety Hazards: A faulty speed sensor can directly affect the vehicle's safety systems (such as ESP, ABS, etc.), leading to a decline in the car's stability performance. Under such conditions, aggressive driving naturally poses significant safety risks. Therefore, to avoid unnecessary losses. Consequences: Once the wheel speed sensor is indeed damaged, it not only causes deviations in the speed display on the dashboard but also results in unstable engine idling and reduced acceleration performance. Additionally, when starting the vehicle or decelerating to a stop during driving, there is a high likelihood of experiencing momentary pauses, or even the possibility of the engine stalling outright, which to some extent directly impacts driving safety.
19
1
Share

What does the M gear in Golf mean?

M gear is the manual mode of the automatic transmission. In this gear, shifting can be done like manual transmission models, upshifting at high speeds and downshifting at low speeds. When using the manual shifting mode, you need to switch the gear lever to the "M" position, and you can directly engage the M gear while driving. The following is a related introduction to the Golf car: 1. Model overview: The Volkswagen Golf is a best-selling car under Volkswagen, the most produced model by Volkswagen, and also the best-selling Volkswagen model, ranking third among the world's best-selling models. 2. Power: The Volkswagen Golf is equipped with Volkswagen's most advanced 1.4TSI engine and a 7-speed dual-clutch transmission, which is powerful and one of the reasons why many consumers favor it.
6
0
Share

What are the reasons for no sound at all when turning the key in the car?

Reasons for no sound at all when turning the key in the car are as follows: Insufficient battery power: First, check whether the car battery has insufficient power, as a depleted battery can cause no response from the starter motor when turning the key. Also, inspect the vehicle's power supply wiring harness and main fuse for any faults. If no issues are found, it is necessary to visit a 4S shop or repair shop for professional inspection and repair. Precautions: Leaving the vehicle parked for extended periods can cause the battery to gradually lose power, leading to depletion. Therefore, it is important to start the engine regularly and avoid prolonged parking. Periodically inspect and clean the battery terminals, accessories, and connecting wires, and apply special grease to the terminals to protect the wiring harness.
17
4
Share

What are the dimensions of an automotive paint baking booth?

Paint baking booth dimensions are typically 7 meters in length, 3 meters in height, and 4 meters in width. Below is a related introduction: Paint Baking Booth: The environment where automobiles undergo paint spraying at the manufacturing plant is a fully enclosed and dust-isolated specialized room. Both the baking temperature and paint spray guns are professionally computer-controlled, with temperatures approximately around 200 degrees Celsius, as there are no plastic components inside the vehicle during this paint spraying process. Features: Traditional automotive paint baking is semi-mechanized and manual, resulting in low work efficiency. The workflow for manual paint baking is complex, requiring high technical skill levels from personnel, significant consumption, and difficulty in ensuring paint baking quality, with frequent accidents. Process: During the painting process, external air is filtered through a primary filter by a fan and sent to the ceiling, then undergoes secondary filtration and purification through a top filter before entering the room.
15
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.