What procedures and documents are required for vehicle transfer?

1 Answers
OWeston
07/25/25 2:54am
Procedures and documents required for vehicle transfer: 1. All document information must be consistent with that of the original owner, and only the owner of the vehicle can transfer the vehicle; 2. All procedures for the vehicle must be complete; 3. The vehicle must meet the annual inspection standards and must not have violations, modifications, etc. If the vehicle has violations, the violation records must be cleared at the relevant departments. If the vehicle has modifications, it must be restored to its original state before transfer can proceed; 4. The vehicle must not have any legal disputes, such as mortgages, loans, etc.; 5. Keep the sales contract as a backup to serve as evidence for rights protection in case of future interest disputes; 6. Be cautious of transfer-related issues, such as insurance not being transferred in time, which may lead to accident disputes.
Was this review help?
4
0
Share
More Forum Discussions

Can motor oils of the same brand but different models be mixed?

Motor oils of the same brand but different models should not be mixed. Although they are from the same brand, the components can vary significantly due to different models. Mixing them may cause unknown chemical reactions, leading to unpredictable effects on the engine. The method for changing motor oil is as follows: 1. Lift the car and remove the bottom guard plate; 2. Place an oil container under the oil pan and unscrew the drain plug; 3. After the oil has drained completely, replace the oil filter and apply a layer of oil around it; 4. Tighten the drain plug, reinstall the guard plate, lower the car, and pour in the new oil. Motor oil serves to lubricate and reduce friction, assist in cooling, seal against leaks, prevent rust and corrosion, and provide shock absorption for the engine.
4
0
Share

Is the Acura RDX a domestically produced car?

The Acura RDX is a domestically produced car. This model is a five-door, five-seat SUV under the Acura brand, with dimensions of 4752mm in length, 1926mm in width, and 1668mm in height, a wheelbase of 2750mm, a fuel tank capacity of 65 liters, and a trunk capacity of 660 liters. In terms of suspension, the Acura RDX features a MacPherson independent front suspension and a multi-link independent rear suspension. For power, the Acura RDX is equipped with a 2.0-liter turbocharged engine, delivering a maximum torque of 380 Nm and a maximum power of 195 kW. The engine incorporates VTEC technology and direct fuel injection, and it uses an aluminum alloy cylinder head and block.
2
4
Share

Is the Chevrolet Orlando compliant with China 6 emission standards?

The Chevrolet Orlando complies with China 6, which refers to the National Phase 6 Motor Vehicle Pollutant Emission Standards. Below are the relevant details: 1. Taking the 2020 Chevrolet Orlando Automatic Enjoyment Edition as an example, it belongs to the compact car category with body dimensions of: length 4684mm, width 1807mm, height 1628mm, a wheelbase of 2796mm, and a fuel tank capacity of 45 liters. 2. The 2020 Chevrolet Orlando Automatic Enjoyment Edition is equipped with a 1.3L turbocharged engine, delivering a maximum horsepower of 163PS and a maximum power speed of 5500rpm, paired with a 6-speed automatic transmission.
10
0
Share

What are the overall dimensions of the X-Trail?

The body dimensions of the X-Trail are: length 4675mm, width 1820mm, height 1722mm. Here is some information about the body dimensions: 1. The X-Trail is a compact SUV produced by Dongfeng Nissan, meeting the standards of a B-segment car. 2. As car body dimensions become larger and wheelbases longer, the interior passenger space increases, and the stability at high speeds also improves. 3. However, larger body dimensions also have their drawbacks, such as reduced maneuverability at low speeds, making it less agile than smaller cars, and more difficult to turn around in congested areas.
4
2
Share

Whose engine is used in the Lynk & Co 03?

The Lynk & Co 03 is equipped with high and low power 1.5T engines, which are inline three-cylinder turbocharged engines jointly developed by Geely and Volvo. These engines inherit a series of advanced technologies from the VEP4 2.0T model. Below is more information about the Lynk & Co 03: 1. Dimensions: The Lynk & Co 03 has a length of 4639mm, a width of 1840mm, a height of 1460mm, and a wheelbase of 2730mm. 2. Interior: The Lynk & Co 03 continues the family-style design of Lynk & Co, featuring extensive use of soft leather wrapping. The center console is slightly tilted towards the driver's seat and is equipped with a 10.2-inch multimedia LCD screen and a 10.25-inch full LCD instrument panel. The overall design incorporates many diamond-shaped elements, which are present on the interior trim, leather seats, and even the LCD instrument panel, center console display, and floor console button designs. 3. Powertrain: The Lynk & Co 03 offers only one 1.5T engine, available in manual and automatic versions. The 1.5T manual version has a maximum output of 156 horsepower, paired with a 6MT transmission, while the 1.5T automatic version offers maximum outputs of 156 horsepower and 179 horsepower, paired with a 7DCT transmission.
2
4
Share

How many kilometers should the brake pads of an Audi A3 be replaced?

Audi A3 brake pads should be replaced approximately every 30,000 to 60,000 kilometers. Brake pads are composed of friction material layer, heat insulation layer, adhesive layer, backplate, etc. The brake caliper pushes the backplate to press the friction material of the brake pad against the brake disc for braking. The following are situations where brake pads need to be replaced: 1. Check the thickness of the brake pads. Use a small flashlight to inspect whether the brake pads have become thin. When the black friction material of the brake pads is nearly worn out and the thickness is below 5 millimeters, replacement should be considered. 2. Braking noise. If you hear a sharp metallic screeching sound during daily driving, this is a warning sign. The wear indicator on the brake pad has started to grind against the brake disc, causing this high-pitched metallic noise. 3. Braking force. When driving and applying the brakes, if you feel the pedal is soft and requires deeper depression to achieve the usual braking effect, it may indicate that the brake pads have largely lost their friction and must be replaced immediately.
5
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.