What Needs to Be Replaced for the Random Jumping of the Buick Excelle Door Lock?

1 Answers
AnthonyMarie
07/30/25 7:48am
Buick Excelle door lock randomly jumping requires replacement of the door lock control assembly and central control module. Below are the roles and functions of the central lock: Roles of the central lock: The full name of the central lock is central control door lock, which is an automotive accessory. Using this lock allows for remotely opening and locking the door without inserting the key into the keyhole. Functions of the central lock: Central control: When the driver locks the door next to them, other doors are simultaneously locked. The driver can open all doors simultaneously through the door lock switch or open a single door individually; Speed control: When the vehicle speed reaches a certain level, all doors can lock automatically to prevent passengers from mistakenly operating the door handle and opening the door; Independent control: Except for the door next to the driver, other doors are equipped with independent spring lock switches for independent control of door opening and locking.
Was this review help?
16
0
Share
More Forum Discussions

How to Park and Turn Off a Porsche Cayenne?

Apply the brakes to slow down and come to a complete stop; once stopped, shift into Neutral (N); engage the parking brake; release the foot brake and ensure the vehicle is stationary; then press the foot brake again and shift into Park (P). The Porsche chassis system features a unique balance mechanism, which consists of two hydraulic rotary motors with four sensors integrated into the front and rear axle active anti-roll bars. This system actively monitors tire level, body dynamics, and acceleration response during driving. A high-pressure pump generates oil pressure up to 180 bar, rapidly adjusting the vehicle's body roll during cornering and balancing the tilt angle. To turn off the vehicle, press the button located on the left side of the gear lever in the center console while the vehicle is powered on. This will deactivate the lift function. The vehicle's lift function mode refers to the suspension lowering the body height during high-speed driving to ensure stability.
17
2
Share

Why Can't the Key Turn When the Steering Wheel is Locked?

Steering wheel lock and key unable to turn occur because the steering wheel was rotated when the car was turned off, causing the steering wheel to automatically lock. This is a normal phenomenon, and the solution is very simple: just turn the steering wheel while simultaneously turning the key to start the ignition. Here are some details about steering wheel lock: 1. Cause: When the car is turned off, the vehicle has a certain self-protection function. If the steering wheel is rotated at this time, the gear latch inside the steering mechanism will be locked, making the steering wheel immovable. Additionally, the key will also be unable to turn, which is designed to prevent car theft. 2. Precautions: When parking the vehicle, always ensure it is parked on a flat surface and the handbrake is properly engaged. Avoid randomly stepping on the brake or turning the steering wheel to prevent it from being locked.
5
4
Share

How long can a 2008 car be driven?

Whether a car is scrapped is not limited by its age, but by its mileage. When the mileage reaches 600,000 kilometers, it must be forcibly scrapped. For details, see Articles 5 and 7 of the "Regulations on Compulsory Scrapping of Motor Vehicles". Cars from 2008 comply with the China III emission standards. Some local governments have corresponding policies prohibiting vehicles that meet the China III emission standards from being driven on the road. Under such circumstances, driving is not possible. First-tier cities like Beijing, Shanghai, Guangzhou, and Shenzhen have introduced corresponding purchase restriction policies. For a 2008 car to continue driving, the following conditions must be met: it must pass the annual inspection; there must be no relevant local restriction policies; and the mileage must not exceed 600,000 kilometers.
3
3
Share

What are the methods for reducing car noise?

You can install some high-end sound-absorbing foam and other materials on the engine hood, which can not only effectively suppress the vibration caused by the hood but also more effectively absorb a large amount of noise, with very noticeable results. Tire noise: Tire noise is generated when the vehicle is driving at high speed and is caused by the friction between the tires and the road surface. Generally speaking, the faster the speed, the greater the vehicle load, and the worse the road conditions, the louder the tire noise will be. Vibration is one of the main sources of tire noise. You can install vibration damping plates along with sound-absorbing pads to reduce the occurrence of vibrations. In addition, you can also try replacing tires with better noise reduction performance, also known as silent tires, which are optimized by tire manufacturers to change the tread design to reduce noise.
16
1
Share

What is the trunk size of the Sportage?

The Sportage's trunk has a minimum depth of 860mm, maximum depth of 1720mm, narrowest width of 1015mm, and height of 755mm. Here are some details about the Sportage:1. The advantage of the Sportage's trunk is that the rear seat backs fold down almost completely flat, and it comes with a 12V power outlet. The disadvantage is the lack of a cargo cover.2. The front fascia design is a highlight of the vehicle, featuring sleek and refined headlight lines. Additionally, the polygonal fog lights are connected by an integrated polygonal bumper, creating strong visual impact with a highly modern feel.3. The Sportage is equipped with multiple high-tech features including hill start assist and hill descent control, fully realizing intelligent vehicle capabilities. With body dimensions of 4400x1855x1660mm, it maintains standard urban SUV proportions.
15
5
Share

How to Step on the Clutch When Pulling Over?

Turn on the right turn signal, release the accelerator, and step on the brake. Note that when stepping on the brake, do not step on the clutch or shift out of gear. Stopping relies on both the friction force of the brake and the engine's resistance. If you step on the clutch and shift out of gear, the speed may still increase. Then step on the clutch, shift out of gear, and pull the handbrake. These actions should be done when the speed drops to about 20 km/h. Stepping on the clutch while braking prevents the car from stalling, and not stepping on the clutch can cause the car to jerk. Before stopping, observe the rear and right side, turn on the right turn signal for 3 seconds before turning right. After stopping, pull the parking brake lever tightly and turn off the engine.
9
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.