What National Emission Standard Does the Cavalier Belong To?

Which brand of engine is used in the BYD Tang fuel version?

The engine of the BYD Tang fuel version is independently developed by BYD, meaning it is a BYD-branded engine. Strictly speaking, the key technologies of the engine are developed by BYD themselves, while some components are mainly sourced externally, as there are no domestic alternatives that meet the required standards. These components include the ignition coil, thermostat, oxygen sensor, dual-mass flywheel, crankshaft sensor, timing chain, timing sensor, etc. More details about the BYD Tang are as follows: 1. The latest model of the BYD Tang fuel version currently on sale is the 2019 model, with an official guide price ranging from 129,900 to 169,900 yuan. It is positioned as a mid-size SUV. In terms of body dimensions, it measures 4870/1940/1720 mm in length, width, and height, respectively, with a wheelbase of 2820 mm. It is available in both 7-seat and 5-seat configurations. 2. The powertrain comes in two variants. The first variant is equipped with a high-power version of a 2.0T inline 4-cylinder turbocharged engine, paired with a 6-speed automatic transmission. It delivers a maximum power of 151 kW, maximum horsepower of 205 PS, and maximum torque of 320 N·m. All models are front-wheel drive. The second variant features a low-power version of the 2.0T inline 4-cylinder turbocharged engine, also paired with a 6-speed automatic transmission. It produces a maximum power of 141 kW, maximum horsepower of 192 PS, and maximum torque of 320 N·m. All models are front-wheel drive.

17

2

Share

What are the differences between BMW 530 and 525?

BMW 525 and 530 have different displacements, one is 2.5 and the other is 3.0. The following is an introduction to the BMW X3: 1. Power: The BMW X3 uses a 2.0T turbocharged engine. BMW has launched three power models, and the 2.0T turbocharged engine is divided into three power levels, namely 25i, 28i and 30i. 2. Engine introduction: The engine of the 25i model has a maximum power of 135kw and a maximum torque of 290nm, the engine of the 28i model has a maximum power of 165kw and a maximum torque of 310nm, and the engine of the 30i model has a maximum power of 185kw and a maximum torque of 350nm.

8

5

Share

What are the reasons why a Mercedes-Benz cannot start?

Here are the reasons why a Mercedes-Benz cannot start: 1. Dead battery: Sometimes you may find that the car cannot start normally in the morning. It is likely because the trunk was not completely closed, causing the trunk light to stay on and drain the battery. 2. Spark plug failure: Spark plugs themselves are prone to damage, and short circuits in high-voltage lines can prevent the spark plugs from firing. Additionally, poor-quality spark plugs can also lead to failure to start normally. 3. Starting circuit malfunction: When starting, there is only a slight "click" sound with no further response. This is caused by a stuck starting relay. In this case, simply pressing the tail of the solenoid to force it forward can connect the starting circuit, allowing the engine to start.

19

0

Share

How to reset the tire pressure on a 2010 Buick Regal?

Vehicle stationary: Prepare the professional reset and matching instruments required for this operation in advance. This operation is highly specialized and requires professional personnel. First, park the vehicle, engage the handbrake, and perform the operation with the vehicle powered on; Dashboard operation: Press the "MENU" button on the turn signal lever to switch the small screen on the dashboard to the "Vehicle Information" column. Rotate the up and down selection buttons on the turn signal lever to find the tire pressure information column. Press and hold (long press) the "SET/CLR" function key at the head of the turn signal lever until "Whether to perform tire pressure learning" is displayed, then select "Yes". After selection, the horn will sound twice to confirm the start of tire pressure learning, and the left front turn signal will light up; Tire deflation: Deflate the tires in the order of left front—right front—right rear—left rear. Unscrew the valve cap and use a small stick like a key to poke the small pin in the valve core to release the air from the tire. Until you hear the horn sound once, and the turn signal on the current tire side goes out, and the right turn signal lights up, you can release the valve. Observe the tire pressure status of each tire on the dashboard. The tire pressure will be lower than the normal value, so you need to inflate the tires in order to bring the tire pressure back to the normal range, generally between 2.3~2.5. After the operation, if "Please service the tire pressure monitoring device" appears, it is normal. If too much air is released, you can rematch.

2

Share

What do the gear letters on a car represent?

The following explains the meanings of the gear letters in a car: 1. P stands for Park, generally used when parking and turning off the engine; 2. N stands for Neutral, typically used for short stops, such as waiting at a traffic light; 3. L stands for Low gear, also known as the climbing gear, which is equivalent to the 1st gear in a manual transmission and is used when climbing hills; 4. D stands for Drive, used when moving forward, and is the most frequently used gear; 5. S stands for Sport, referred to as Sport mode in many models. Engaging the S gear keeps the engine at higher RPMs, increasing torque output for greater power, commonly used when overtaking.

20

4

Share

What Causes a Truck to Pull to One Side When Braking?

The reasons for braking deviation are as follows: 1. Uneven braking force on the left and right sides of the same axle: Different clearances between the rear brake shoes and drums on each side can cause asynchronous braking, or variations in contact area can also lead to uneven braking force. If this occurs, adjust the left and right brake clearances according to specifications or resurface the contact area of the brake shoes. 2. Different braking torque on the left and right sides of the same axle: This results in one-sided braking. Common causes include leaking brake wheel cylinders, rusted pistons, oil-contaminated drum brake shoes, or differing surface roughness between brake discs and pads or drums and shoes. Inspect and rectify these issues as needed. 3. Uneven tire pressure, tread patterns, or wear levels on both sides: This can cause the actual rolling radius of the wheels to differ, leading to unequal straight-line travel distances. In such cases, the vehicle may pull to one side even when not braking. 4. Improper body repair on a previously damaged vehicle resulting in unequal wheelbase on both sides: Suspension components such as uneven or failed shock absorber springs, loose suspension ball joints, or deformed connecting rods can interfere with each other during braking, causing the vehicle to pull to one side. Additionally, incorrect wheel alignment can also lead to this phenomenon.

6

2

Share

What National Emission Standard Does the Cavalier Belong To?

Which brand of engine is used in the BYD Tang fuel version?

What are the differences between BMW 530 and 525?

What are the reasons why a Mercedes-Benz cannot start?

How to reset the tire pressure on a 2010 Buick Regal?

What do the gear letters on a car represent?

What Causes a Truck to Pull to One Side When Braking?

What are the maintenance items for a BMW 3 Series at 40,000 kilometers?

What is the crash test rating of the Hyundai ix35?

Differences Between 525Li and 530Li?

What causes the engine warning light to illuminate in an Audi A4?