What model of tires should be replaced for the Fista?

1 Answers
NoraDella
07/29/25 8:24pm
Modern Fista's original tires are from the brands Nexen and Maxxis, with tire sizes varying by configuration: 205/55-R16, 225/45-R17, and 225/40-R18. The tire replacement cycle for the Modern Fista is 60,000 to 120,000 kilometers. Tires older than 6 years must be inspected by qualified technicians, even if they have been rarely used, never used, or show no obvious damage. The method for replacing tires on the Modern Fista is as follows: 1. First, unscrew all the tire nuts. The nuts should be removed in a diagonal order to avoid damaging the wheel hub. 2. Place the jack directly under the support point, then slowly adjust the jack to raise the chassis. Once the tire is off the ground, it can be removed. 3. Place the new tire and manually secure the nuts. Do not tighten the nuts too forcefully to avoid stripping the threads. The nuts should be fully tightened once the wheel is in contact with the ground.
Was this review help?
12
0
Share
More Forum Discussions

What is the displacement of the Audi 35TFSI?

Audi 35TFSI has a displacement of 1.4 liters. Here, FSI refers to Fuel Stratified Injection, and TFSI stands for Turbocharged Fuel Stratified Injection. A turbocharged engine is an engine equipped with a turbocharger, which is essentially an air compressor that increases the intake air volume by compressing air. The main function of turbocharging is to enhance the engine's intake volume through the turbocharger, thereby increasing the engine's output power and torque. Audi is a luxury car brand under Audi AG, a subsidiary of the Volkswagen Group. The company is headquartered in Ingolstadt, Germany, and its main models include A1, A3, A4, A5, A6, A7, A8, Q1, Q2, Q3, Q5, Q7, Q8, TT, R8, as well as the S and RS performance series.
10
0
Share

Does the Buick GL6 have a 4-cylinder engine?

The Buick GL6 does not have a 4-cylinder engine. Currently, it is only equipped with a 1.3T three-cylinder engine. The 1.3T dual-injection turbocharged engine, paired with a 6-speed DSS intelligent transmission, delivers smooth and powerful power output across various speed ranges, fully meeting the demanding power requirements of MPV models under different load conditions. In terms of exterior design, the Buick GL6 features a family-style front face to enhance its recognition, along with winged chrome grille and winged headlights, further emphasizing Buick's design language. The vehicle dimensions are 4692mm in length, 1794mm in width, and 1626mm in height, with a wheelbase of 2796mm. For the chassis system, the Buick GL6 adopts a MacPherson independent front suspension and a multi-link independent rear suspension.
20
4
Share

Can Electric Vehicles Drive Through Deep Water?

Under normal usage conditions, including driving through water or in high temperatures, electric vehicles do not pose potential hazards. Below is an introduction to the classification of electric vehicles: 1. Battery Electric Vehicles (BEVs): BEVs are powered by electric motors. Compared to fuel-powered vehicles, the main differences lie in four major components: the drive motor, speed controller, power battery, and onboard charger. Instead of gas stations, they rely on public ultra-fast charging stations. The quality and value of BEVs depend on these four components, and their applications are directly related to their configuration. 2. Series-Parallel Hybrid Electric Vehicles: These vehicles combine series and parallel driving modes. Their structural feature allows them to operate in either series hybrid mode or parallel hybrid mode, combining the advantages of both. 3. Fuel Cell Electric Vehicles (FCEVs): FCEVs use fuel cells as their power source. The chemical reaction process in fuel cells does not produce harmful byproducts, making FCEVs pollution-free. The energy conversion efficiency of fuel cells is 2-3 times higher than that of internal combustion engines, making FCEVs an ideal choice in terms of energy utilization and environmental protection.
11
4
Share

What to Do When Car Key Buttons Are Broken?

Car key buttons broken need to be replaced at a 4S shop. Below are three types of introductions regarding the usage methods of car keys: 1. Active working mode: The principle is to control the car door through the vehicle's electronic module. Simply press the key button to send an unlock/lock command, which, after verification by the vehicle's electronic module, can open/close the car door. 2. Coil induction working mode: Mainly involves placing an encrypted chip inside the key. During the unlocking process, the vehicle's RF transceiver verifies whether the key matches to determine if the engine can be started. This is primarily used in special situations when the key is out of battery, allowing the car to still start normally. 3. Passive working mode: When the car owner enters the sensing area of the key system, as long as the hand touches the car door handle, the carried identification "key" will receive the low-frequency signal sent by the car. If this signal matches the identification information stored in the "key", the "key" will be awakened. After being awakened, the "key" will analyze the authentication command sent by the car and send corresponding signals, which are encrypted to enhance security.
4
5
Share

Where to Add Windshield Washer Fluid in Volkswagen?

The windshield washer fluid filler port of the Volkswagen Lavida is located on the right side of the engine compartment. Below are the specific functions of automotive windshield washer fluid: 1. Cleaning Performance: Windshield washer fluid is formulated with various surfactants and additives. Surfactants typically have functions such as wetting, penetrating, and solubilizing, thereby achieving the effect of cleaning and removing dirt. 2. Antifreeze Performance: It can significantly lower the freezing point of the liquid, thus providing antifreeze effects and quickly dissolving frost. 3. Anti-Fog Performance: A single-molecule protective layer forms on the glass surface. This protective film prevents the formation of fog droplets, ensuring the windshield remains clear and transparent with a clear field of vision. 4. Anti-Static Performance: After cleaning with windshield washer fluid, substances adsorbed on the glass surface can eliminate surface charges, providing anti-static performance.
6
1
Share

What are the main components of the crank connecting rod mechanism?

The crank connecting rod mechanism mainly consists of three parts: the engine block group, the piston connecting rod group, and the crankshaft flywheel group. The engine block serves as the framework of the engine and the installation base for various mechanisms and systems of the engine. It houses all the main components and accessories of the engine, both internally and externally, and bears various loads. The piston, together with the cylinder head and cylinder wall, forms the combustion chamber. It withstands the gas pressure in the cylinder and transmits the force to the connecting rod through the piston pin, thereby driving the crankshaft to rotate. The function of the crank connecting rod mechanism is to provide a combustion space, convert the expansion pressure of the gas generated after fuel combustion acting on the piston top into the torque of the crankshaft's rotation, and continuously output power. The working principle of the crankshaft includes: 1. Converting gas pressure into crankshaft torque; 2. Transforming the reciprocating motion of the piston into the rotational motion of the crankshaft; 3. Converting the force of combustion acting on the piston top into crankshaft torque to output mechanical energy to the working machinery.
17
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.