What model is bmw7200lg?

What is the difference between low beam and high beam indicators?

Here are the specific differences: 1. The angle between the light rays and the horizontal line differs in the indicators: In the low beam indicator, the light rays usually form a 45° angle with the horizontal line, meaning they illuminate the nearby area; in the high beam indicator, the three light rays are parallel to the horizon, allowing for a longer range and better visibility of the road ahead. 2. The colors may differ: Generally, on the dashboard, the high beam indicator is blue, while the low beam indicator is green, with the light rays angled downward. There might be variations between different brands and models, but this is the basic standard.

10

2

Share

Where to Install Car Door Vibration Damping Pads?

Install them at the closest point between the door and the vehicle body panel when the door is closed. Below is relevant information about car door vibration damping pads: 1. Function: They prevent direct contact between the shock absorber and the vehicle body. When the car turns and the center of gravity shifts to one side, causing body tilt and spring compression, these pads provide support, thereby reducing vehicle roll. 2. Materials: The pads are made of paper, rubber sheets, or copper sheets, serving as sealing materials placed between two surfaces to enhance sealing. They act as sealing elements installed between static sealing surfaces to prevent fluid leakage. They are attached to the vehicle body using adhesive, and the adhesive materials are generally mild, so they won't cause damage to the vehicle body surface.

20

3

Share

Can Water Enter the Transmission of a Flooded Vehicle?

Whether water enters the transmission of a flooded vehicle depends on the vehicle's condition. Below is a detailed explanation regarding water ingress in the transmission of flooded vehicles: Vehicle in Motion: Generally, as long as the vehicle is still moving and the engine is running, water will not enter the transmission even if it is submerged. Although the transmission has a vent hole, the internal pressure generated while the transmission is operating prevents water from entering. Vehicle Stationary: When the vehicle is parked and the transmission is not operating, if the transmission housing is submerged in water, water can enter through the vent hole. In this scenario, the transmission must be inspected, and the transmission fluid must be replaced. If the fluid is not replaced within 4 hours, even if repairs are done three to five days later, transmission issues may still arise after five months.

13

4

Share

Can You Drive If the Exhaust Pipe Is Submerged in Water?

You cannot drive if the exhaust pipe is submerged in water. If the car's exhaust pipe takes in water and the engine stalls, never attempt to restart it forcefully. Instead, immediately call for rescue services and wait for assistance. Below is an introduction to vehicle wading: Introduction: Vehicle wading, as the name suggests, refers to driving through low-lying, waterlogged roads or passing through water. This typically occurs during rainy weather in low-lying areas where inadequate drainage leads to water accumulation on the road. Precautions: Before wading, observe the road conditions carefully; during wading, maintain steady power; after wading, inspect the electrical system.

12

5

Share

How Many Levels Are There for Flood-Damaged Vehicles?

Flood-damaged vehicles are categorized into three levels based on the extent of water immersion: water-damaged vehicles, partially submerged vehicles, and fully submerged vehicles. To identify a flood-damaged vehicle, you can check the following three aspects: Open the engine compartment: inspect the entire engine block and surrounding areas for signs of rust and mold. Fuse box: there is a fuse box inside the engine; open it to check for mud or sand. Pull the seatbelt all the way out: smell for any musty odor and look for mold stains. After a car is submerged in water, water will seep into the seatbelt. If the owner is unsure how to proceed, they can seek assistance from a third-party professional vehicle inspection agency to conduct an on-site inspection of the used car.

11

3

Share

How to Open the S90 Hood?

There is a hood release switch located at the lower left corner of the driver's seat. Pull the switch to activate it, at which point the hood will make a sound. Gently lift the hood upwards slowly, then locate the hood support rod in the front compartment and secure the hood onto the rod. Functions of the hood: 1. Airflow guidance: For objects moving at high speeds through air, the aerodynamic drag and turbulence generated around the object directly affect its trajectory and speed. The hood's shape effectively adjusts the direction of airflow relative to the car's movement and mitigates resistance. 2. Protection for the engine and surrounding pipeline components: Beneath the hood lie critical automotive components including the engine, electrical circuits, fuel system, and transmission system.

13

1

Share

What model is bmw7200lg?

What is the difference between low beam and high beam indicators?

Where to Install Car Door Vibration Damping Pads?

Can Water Enter the Transmission of a Flooded Vehicle?

Can You Drive If the Exhaust Pipe Is Submerged in Water?

How Many Levels Are There for Flood-Damaged Vehicles?

How to Open the S90 Hood?

Will the fuel tank of a flooded car take in water?

Can a Flooded Car with No Engine Problems Still Be Driven?

What is the purpose of the small black stick on the car dashboard?

Will crossing the solid white line on the highway result in penalty points?