What materials are needed to renew a driver's license?

1 Answers
JessicaLee
07/29/25 11:26am
A driver's license does not need to be renewed, but it must be replaced before its expiration date. The required materials are as follows: 1. "Motor Vehicle Driver's License Application Form"; 2. Proof of identity of the motor vehicle driver; 3. The motor vehicle driver's license; 4. A medical certificate issued by a county-level or higher medical institution or a military medical institution at the regimental level or above, proving the driver's physical condition; 5. The motor vehicle driver may authorize an agent to handle the replacement, reissuance, submission of the physical condition certificate, extension, and cancellation of the license. When applying for motor vehicle driver's license services, the agent must submit their proof of identity and the application form or physical condition certificate signed by both the motor vehicle driver and the agent; 6. Three recent one-inch, bareheaded, white-background color photos.
Was this review help?
9
1
Share
More Forum Discussions

Can You Still Drive with a Noisy Tensioner Pulley?

You should not drive with a noisy tensioner pulley. The tensioner pulley contains bearings, and if there is abnormal noise, it indicates that the bearings are damaged. This may lead to timing belt/chain misalignment, ignition and valve timing issues, affecting the normal operation of the vehicle. Below is additional information: 1. Maintain Tension: The tensioner pulley directly contacts the timing belt or chain to ensure proper tension during operation, preventing slippage, misalignment, or loosening, and reducing wear on the sprockets and chain. 2. Adjust Tightness: It is used to adjust the tightness of the timing belt, but its lifespan is relatively short. Many vehicles experience tensioner pulley failure before the belt wears out. Generally, the tensioner pulley is replaced along with the timing belt. 3. Replacement Interval: It is recommended to replace the tensioner pulley every 3-5 years or 80,000-100,000 kilometers. Refer to the vehicle's maintenance manual for specific replacement intervals.
16
3
Share

What is the normal cylinder pressure for a car engine

Automobile engine cylinder pressure is around 1000kpa. Generally, gasoline engines are around 1000kpa, diesel engines are around 2000kpa, most fuel injection engine cylinder pressures are between 1200~1400kPa, and a few high compression ratio engines have cylinder pressures above 1700kPa. The cylinder is a piston in the car's combustion chamber that is driven by the pressure or expansion force of the working fluid. The classification of cylinders is as follows: 1. Single-acting cylinder: Only one end has a piston rod, with air supplied from one side of the piston to generate pressure, which pushes the piston to produce thrust for extension, and returns via spring or self-weight. 2. Double-acting cylinder: Air is alternately supplied from both sides of the piston, producing force in one or two directions. 3. Diaphragm cylinder: Uses a diaphragm instead of a piston, producing force in only one direction, with spring reset. It has good sealing performance but a short stroke.
19
3
Share

What is the reason why the car still has power after removing the key?

If the power remains on after removing the key, it may be due to a damaged or worn key switch, or it could be caused by a short circuit in the electrical wiring that leads to switch failure. The basic components of a remote key consist of the following two points: 1. Transmitter: Composed of a transmission switch, transmission antenna, integrated circuit, etc., it contains an identification code storage circuit and an amplitude modulation circuit, with a button-type lithium battery installed on the opposite side of the circuit. The transmission frequency uses radio waves, and each press of the transmission switch button sends a signal once. 2. Receiver: After the transmitter sends the identification code using shortwave modulation, it is received by the car's shortwave antenna and enters the shortwave high-frequency amplification processor of the receiver's electronic control unit through a distributor for demodulation, where it is compared with the demodulator's identification code.
10
4
Share

What is the function of a stabilizer bar?

The function of a car stabilizer bar is to maintain vehicle stability and prevent excessive body roll. Here is some information about automotive stabilizer bars: 1. Function: The stabilizer bar is an auxiliary elastic component in a vehicle's suspension system. Its purpose is to prevent excessive lateral roll during cornering and maintain body balance as much as possible. 2. Purpose: Its objectives are to prevent vehicle lateral rollover and improve ride comfort. 3. Structure: The stabilizer bar is a torsion bar spring made of spring steel, shaped like a "U", mounted horizontally on the front and rear suspensions. The middle section of the bar is connected to the body or frame via rubber bushings, while both ends are linked to suspension control arms through rubber pads or ball joints at the sidewall ends.
16
2
Share

Is the Civic available as an imported model?

The Civic is available as an imported model. Honda has introduced various Civic models to cater to the preferences of consumers in different countries. Civic Interior: The new-generation Civic features a dark-toned interior with accents of bright silver trim. It also comes equipped with a newly designed three-spoke multifunction steering wheel, which offers a sportier look compared to the current model. Civic Features: In terms of features, the new model includes a multimedia system with a display screen, automatic climate control, an electronic parking brake, auto hold, and an ECO mode for improved fuel efficiency. Civic Powertrain: The new-generation Civic is powered by a 1.5T direct-injection turbocharged engine.
12
0
Share

How many points are deducted for driving straight in a bus lane?

Illegally occupying a bus lane violates the provisions of the "Road Traffic Safety Law": If a motor vehicle does not drive in the designated lane, the driver's license will be deducted 2 points, and a fine of 200 yuan will be imposed. The fine must be paid within 15 days. Notes: 1. Be aware of the permitted hours: Clearly understand the permitted hours for bus lanes. Many bus lanes are dedicated to buses during peak hours, and other vehicles can enter during non-peak hours. Be sure to know the dedicated time slots to avoid entering. 2. Familiarize yourself with the road: Familiarize yourself with the road in advance. If you are not familiar with the local roads, carefully identify road signs or follow taxis, which usually won’t lead you wrong. 3. Avoid being forced to yield the lane: Inexperienced drivers may be forced into the bus lane by other vehicles. Therefore, novice drivers should be cautious. When being squeezed, you can slow down and yield, but never give up the lane.
8
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.