What Material is Best for Engine Guards?

How to Clean and Maintain Leather Seats?

When there is only some dust, wipe with a damp towel and then dry with a dry towel. You can also use a long-haired brush in combination with a vacuum cleaner with strong suction. For surface stains, spray a universal cleaner on the surface and then wipe it. For severe grease stains, you can use a leather cleaner in combination. For deep cleaning, use a steam cleaner to thoroughly remove bacteria and odors from within. To prevent leather products from fading, aging, hardening, or cracking, and to restore their luster, use leather care products for maintenance.

18

2

Share

How to Remove the Wiper Blades on a Mercedes-Benz C260L?

First, lift the wiper arm, raise the small cover, and pull down the wiper bracket. Fold it up 80 degrees, then remove it. Push the wiper blade in the direction of the car's front. When the wiper arm swings to a certain position, it will automatically lock in place. Press the wiper's release button while gently wiggling the entire wiper blade upwards to remove the old rubber blade. Open both sides at the bottom of the wiper blade and remove the wire clip. Note that the clip has a groove that must align with the protruding part of the wiper. Next, release the two clips securing the wiper blade and pull out the old rubber blade. Be careful with the force when removing the middle connecting mechanism and the side clips.

20

2

Share

How to Turn on the Heater in an Older Buick Excelle?

First, you need to press the brake pedal and start the engine. Then, turn the key to the ST position to start the engine until the idle speed stabilizes. Next, turn the fan speed knob. Rotate the temperature mode knob to the left to activate the cooling mode. Rotate the temperature mode knob to the right to activate the heating mode. Press the A/C switch to turn on the compressor. Press the recirculation button to activate the interior recirculation mode. To adjust the fan speed, click the fan blade icon on the air conditioning panel to increase or decrease the airflow.

12

5

Share

How Often Should Vehicle Antifreeze Be Replaced?

Vehicle antifreeze should be replaced every two years. This is only a reference interval; for commercial vehicles with higher mileage, the replacement interval should be shorter. Since driving conditions vary for each vehicle, the replacement should be based on actual usage. Check the antifreeze's condition—if it is insufficient, replenish it promptly. If suspended particles, sediment, or signs of deterioration or discoloration are observed, replace the antifreeze immediately and flush the system. Procedure for replacing antifreeze: Before a complete antifreeze replacement, conduct a thorough inspection to check for leaks or cracks in all pipes, with particular attention to the five-way hose. The five-way hose, named for its five connection points to various components, distributes antifreeze to different parts of the car. If any leakage is detected in this section, replace the hose or reseal the connections as needed. Drain the old antifreeze, then flush the fluid channels with clean water. Add water to the antifreeze reservoir and continue filling until water flows continuously through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to circulate the water. Initially, the discharged water may appear slightly pinkish—keep adding clean water until it runs clear. Remember to disconnect the heater hose and drain the heater core completely. About an hour after draining, add new antifreeze through the radiator hose to allow quick flow into the radiator. Then, fill the antifreeze reservoir with another bottle until it is nearly full. Run the engine for about 10 minutes; as air is purged from the cooling system, the fluid level will drop. Top up the antifreeze to the "MAXT" mark on the reservoir.

15

3

Share

How to Use FAW-Volkswagen Car-Net?

For Volkswagen imported vehicles equipped with Volkswagen Car-Net functionality, sign a service contract with the dealer, who will then assist in completing the service account setup. Open the Volkswagen Car-Net homepage to register an account and activate it via the activation link in your email. Log in to your account, fill in personal details, set a 4-digit personal identification number (PIN), and then add your vehicle. After adding the vehicle, you will receive an online matching PIN code. Take this PIN code to a 4S dealership to have the after-sales service team activate it for you. After entering the PIN code, wait a few minutes. Once you receive an SMS confirming the successful activation of Car-Net and the green light on the car roof illuminates, the process is complete.

14

1

Share

How to Connect Bluetooth for 2012 Audi A4L?

Then search for Bluetooth devices on your phone, select the found device for pairing and connection. The pairing password is: 0000. After successful pairing, the connection is established. Set your phone's Bluetooth to "Visible to All" or make it discoverable/open for detection. First, turn on the Bluetooth function on both your phone and the car's Bluetooth device, and set your phone's Bluetooth to "Visible to All" or make it discoverable/open for detection. You can make and receive calls on the car's Bluetooth device, play music on your phone, and enjoy the music through the car's Bluetooth device.

5

3

Share

What Material is Best for Engine Guards?

How to Clean and Maintain Leather Seats?

How to Remove the Wiper Blades on a Mercedes-Benz C260L?

How to Turn on the Heater in an Older Buick Excelle?

How Often Should Vehicle Antifreeze Be Replaced?

How to Use FAW-Volkswagen Car-Net?

How to Connect Bluetooth for 2012 Audi A4L?

How to remove the rear door lock assembly on a Mercedes-Benz S320?

Where is the license plate number Ji D from?

What is the process for replacing a damaged license plate?

What to Do When the Car Engine Temperature is Too High?