What maintenance is required for a new car at 10,000 kilometers?

What is the normal tire pressure for the Jade?

The normal tire pressure range for the Jade is 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2 bar in winter and decreased by 0.1 bar in summer. This data is based on the international GBT2978-2008 standard. The Jade is equipped with a tire pressure monitoring function. The tire pressure can be checked on the central display. This tire pressure monitoring system uses ABS wheel speed sensors to compare the rotational speed differences between the tires to determine if there is any abnormal tire pressure. If an abnormality is detected, it will immediately alert the driver. The module is integrated into the ABS pump. Generally, a tire pressure exceeding 2.8 bar is considered too high, while a tire pressure below 2.0 bar is considered too low. Hazards of overinflated tires: Reduced tire friction and adhesion, affecting braking performance; causes steering wheel vibration and deviation, reducing driving comfort; accelerates wear on the central tread pattern, shortening tire lifespan; increases vehicle vibration, indirectly affecting the lifespan of other components; causes excessive stretching of tire cords, reducing tire elasticity and increasing the load on the vehicle during driving. Hazards of underinflated tires: Increased friction coefficient with the road surface, leading to higher fuel consumption; makes the steering wheel heavy and prone to deviation, compromising driving safety; increases movement of various parts of the tire, causing abnormal heating due to excessive rolling; reduces the functionality of cords and rubber, leading to delamination or cord breakage and excessive friction with the rim, causing damage to the tire bead area and abnormal wear; multiplies the friction between the tire and the ground, rapidly increasing tire temperature, softening the tire, and drastically reducing its strength. High-speed driving under these conditions may lead to a tire blowout. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no stamp on top, four small spikes at the bottom, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure. Usually, the system alerts when the pressure is below 1.8 bar or above 3.0 bar. In this case, tire inspection and pressure adjustment are required. Tire pressure monitoring not reset. After inflating the tires, if the tire pressure is not reset in time, the system will still record the previous data, causing the tire pressure monitoring light to stay on. Simply reset the tire pressure to resolve this issue. Damaged tire pressure sensor. The tire pressure sensor, which monitors tire pressure, is directly installed inside the tire and connected to the tire inflation valve. If the sensor is damaged due to impact while driving, the tire pressure warning light will illuminate. For sensor damage, the only solution is to replace it with a new one.

3

4

Share

How many cylinders does the GAC Trumpchi GS3 engine have?

The GAC Trumpchi GS3 is equipped with a three-cylinder engine, model 4A15K1, with a maximum power of 124 kW, maximum torque of 265 Nm, and maximum horsepower of 169. The engine of the GAC Trumpchi GS3 is independently developed and produced by Guangzhou Automobile Group Passenger Vehicle Co., Ltd., and is classified as a domestic engine. For daily maintenance of the GAC Trumpchi GS3 engine, the following methods can be applied: Use lubricating oil of appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional devices in the intake and exhaust systems and usage conditions; for diesel engines, choose CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will deteriorate during use. After a certain mileage, performance degradation can cause various engine issues. To prevent faults, change the oil regularly according to usage conditions and maintain an appropriate oil level. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is clogged and oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing oil to bypass through the bypass valve, bringing contaminants back to the lubrication areas, accelerating engine wear and increasing internal pollution. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use radiator cleaner to clean the radiator. Removing rust and scale not only ensures normal engine operation but also extends the overall lifespan of the radiator and engine.

16

5

Share

Which country's engine is used in the Hongqi H9?

The engine of the Hongqi H9 is independently developed by China FAW and is a domestically produced engine. The engine model of the Hongqi H9 is CA4GC20TD-31. The 2.0T version has a maximum power of 185 kW and a maximum torque of 380 Nm, while the 3.0T version has a maximum power of 208 kW and a maximum torque of 400 Nm. For daily maintenance of the Hongqi H9 engine, the following methods can be used: Use lubricating oil of the appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions. For diesel engines, CB--CD grade diesel engine oil should be selected according to the mechanical load, with the selection standard not lower than the manufacturer's requirements. Regularly change the oil and oil filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, the performance deteriorates, causing various problems for the engine. To avoid malfunctions, the oil should be changed regularly according to usage conditions, and the oil level should be kept moderate. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is blocked and oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing oil to bypass through the bypass valve and carry contaminants back to the lubrication area, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from component wear to form sludge. A small amount remains suspended in the oil, while a large amount precipitates, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.

15

5

Share

What Causes the Car Engine Malfunction Light to Flash?

When the engine malfunction light flashes, it indicates a serious engine issue that requires immediate parking and inspection. The specific reasons may include the following seven: Sensor malfunction: The sensors referred to here include those for coolant temperature, crankshaft position, air flow, intake air temperature, oxygen sensors, etc. When these sensors are damaged, have poor connections, or experience signal interruptions, the car's ECU cannot accurately obtain engine data, which will trigger the engine malfunction light. Fuel quality issues: If fuel and engine oil are not added as required by the manufacturer, it may cause engine wear and trigger the malfunction light. Poor combustion of the air-fuel mixture: Poor combustion can lead to engine carbon deposits or knocking. When detected by the oxygen sensor and reported to the ECU, the malfunction light will illuminate as a warning. Issues such as spark plug failure, ignition coil failure, fuel pump failure, or fuel line blockage can all cause poor combustion of the air-fuel mixture. Turbocharging issues: Problems with the intake boost pipeline or turbocharger can also trigger the engine malfunction light. The most common issue is turbocharger damage, accompanied by symptoms such as oil leaks, excessive oil consumption, reduced power, metallic noises, or blue/black smoke from the exhaust. Intake issues: If there are problems with the car's intake, it may lead to engine pipeline blockages, and in severe cases, trigger the engine malfunction light. A dirty air filter that is not cleaned regularly can cause intake problems. Exhaust issues: Exhaust faults can also trigger the engine malfunction light. Common causes include rear oxygen sensor failure, catalytic converter issues, exhaust camshaft and bearing failures, with the catalytic converter being the most frequent culprit. Using leaded gasoline, lead or silicon-based lubricant additives, physical damage to the catalytic converter, or fuel system malfunctions can easily cause catalytic converter issues. Anti-theft system malfunction: If the car's electronic anti-theft system fails or the anti-theft controller does not match the engine electronic controller, the anti-theft system can prevent the engine from operating normally and trigger the malfunction light. Generally, the engine malfunction light can appear in four states: steady yellow, flashing yellow, steady red, or flashing red. The severity of the issue increases from steady to flashing and from yellow to red. In order of severity: flashing red > flashing yellow > steady red > steady yellow. If the engine malfunction light comes on, follow these steps: First, check if the engine is running normally, whether there is shaking, black smoke, etc. If so, avoid restarting the engine. Note: Do not restart the engine if the red light is on. If the engine can start, turn it off for 5-10 minutes, then without pressing the brake, press the start button once or turn the key halfway to the "on" position without pressing the clutch. The car will perform a self-check after powering on. Wait 5-10 seconds to see if the malfunction light turns off. If the light remains on, visit a service station as soon as possible. The service station can use a portable diagnostic tool to read the fault code, identify the issue, and perform targeted repairs.

9

2

Share

Is the Audi R8 four-wheel drive or rear-wheel drive?

Audi R8 is four-wheel drive. Four-wheel drive means that the vehicle maintains a four-wheel drive form throughout the entire driving process, with the engine output torque distributed to the front and rear wheels in a fixed ratio. The Audi R8 has a body size of: length 4429mm, width 1940mm, height 1236mm, wheelbase 2650mm, fuel tank capacity 73 liters, and a body structure of a 2-door, 2-seat hardtop sports car. The Audi R8 is equipped with a 5.2L naturally aspirated engine and a 7-speed transmission, with a maximum power of 456 kilowatts, maximum power speed of 8250 revolutions per minute, maximum torque of 570 Newton-meters, and maximum torque speed of 6500 revolutions per minute.

19

5

Share

Where is the handbrake located on the Mercedes-Benz E300?

The handbrake position of the Mercedes-Benz E300 is located: next to the left foot of the brake pedal, there is a small brake pedal which serves as the handbrake. The function of the handbrake is to provide resistance to the car when parked, preventing it from rolling. The dimensions of the Mercedes-Benz E300 are: length 5078 mm, width 1860 mm, height 1484 mm, with a wheelbase of 3079 mm and a fuel tank capacity of 66 liters. The Mercedes-Benz E300 is equipped with a 2.0T turbocharged engine, delivering a maximum power of 190 kW, with the maximum power speed ranging from 5800 to 6100 rpm, and a maximum torque of 370 Nm. It is paired with a 9-speed automatic transmission, and both the front and rear suspensions use multi-link independent suspension systems.

3

1

Share

What maintenance is required for a new car at 10,000 kilometers?

What is the normal tire pressure for the Jade?

How many cylinders does the GAC Trumpchi GS3 engine have?

Which country's engine is used in the Hongqi H9?

What Causes the Car Engine Malfunction Light to Flash?

Is the Audi R8 four-wheel drive or rear-wheel drive?

Where is the handbrake located on the Mercedes-Benz E300?

Which gear should an automatic transmission car be in for normal driving?

How Long Should a Beginner Wait Before Driving on the Highway?

Where is the jack positioned when changing tires?

How are oil grades classified?