What lights to use when a traffic accident occurs at night and is difficult to move?

What Are the Common Faults in New Energy Vehicles?

Here are the common faults in new energy vehicles and their causes: 1. Exclamation Mark Fault: 1. The system detects that the battery temperature exceeds the preset safety threshold. 2. The system detects sporadic fault signals and autonomously restricts some vehicle functions. 2. Power Battery Insulation Fault: Water ingress in the electric vehicle battery box or connectors, battery cell leakage, high environmental humidity, false insulation alarms, or insulation failure in other high-voltage components (such as the controller, compressor, etc.). 3. Power Limitation Light On: 1. The power battery is nearly depleted, and the vehicle enters a protective state. 2. The system detects a fault in the vehicle's circuit system. 3. The power battery temperature exceeds the safe range. 4. Power Battery Temperature Fault: 1. Loose cooling fan connector. 2. Cooling fan malfunction. 5. Abnormal Motor Noise: 1. The concentricity between the motor and rear axle does not meet the standard. 2. Poor contact between the brushes and commutator. 6. Complete Power Loss in Electric Vehicle: 1. Blown fuse. 2. Loose wiring connector. 3. Faulty power switch.

9

5

Share

What are the reasons for the lack of acceleration in the Besturn X80?

Here are the specific reasons for the lack of acceleration in the Besturn X80: 1. Incorrect engine oil level: There are specific standards when changing the engine oil. If too much oil is added, the crankshaft will operate with more difficulty, requiring greater power to push, leading to a lack of acceleration. Excessive oil may also leak into the combustion chamber, causing rapid oil consumption and engine carbon buildup, which can damage the engine. If too little oil is added, parts won't receive sufficient lubrication, and power will decrease. Use the dipstick to check the oil level and ensure it is slightly above the midpoint. This ensures proper engine lubrication without excessive pressure on the crankshaft. 2. Mismatched engine oil: Different engines require different types of oil. If acceleration issues arise after an oil change, the oil may not be suitable. Oil with too high viscosity makes crankshaft operation difficult, while oil with too low viscosity may cause noise. It is recommended to replace the oil according to the standards specified in the car manual. 3. Clogged oil filter or severe carbon buildup: When changing the oil, the oil filter should usually be replaced as well. If the filter is clogged and not replaced in time, oil will bypass through the relief valve, leading to reduced power and increased engine wear.

5

2

Share

What causes the hissing sound near the intake pipe of the Besturn X80?

The hissing sound near the intake pipe of the Besturn X80 is caused by an air leak in the intake pipe. Below are specific details about the manifestations of an intake pipe leak: Engine power loss: Since the air entering the engine through cracks in the intake pipe bypasses the air flow sensor, this portion of air dilutes the combustible air-fuel mixture in the engine cylinders, leading to symptoms of engine power loss. Poor wiring includes substandard alloy wires and inadequate insulation on the outer layer of the wires. The pulse current IN through the high-voltage wire weakens due to poor conductivity, which also results in incomplete or slow combustion of the air-fuel mixture. Increased nitrogen oxide emissions: Since nitrogen oxides in vehicle exhaust are formed in high-temperature, oxygen-rich environments, an overly lean air-fuel mixture further promotes the generation of nitrogen oxides, thereby increasing the emission of vehicle exhaust pollutants. Starting difficulties: During startup, the engine requires a higher concentration of the air-fuel mixture. The lean mixture caused by an intake pipe leak leads to difficulties in starting the engine. Symptoms include the starter suddenly losing power during startup, accompanied by a burning rubber smell or smoke emanating from the battery area, often due to poor contact and overheating at the terminal posts or clamps.

11

4

Share

Should Fog Lights Be Turned On in Rainy Weather?

Fog lights should be turned on when visibility drops below 200 meters during rainy weather. Automotive fog lights are installed at the front and rear of the vehicle, serving to illuminate the road and provide safety warnings in foggy or rainy conditions. They enhance visibility for both the driver and other road users. The primary function of fog lights is to make the vehicle more visible to others when visibility is significantly reduced due to weather conditions such as fog or heavy rain. Therefore, fog light sources need to have strong penetration capabilities. Most vehicles use halogen fog lights, while LED fog lights are considered a more advanced option. The correct usage of fog lights is as follows: When visibility is between 200m and 500m: Low beam headlights, width indicator lights, and tail lights must be turned on. The speed should not exceed 80 km/h, and a following distance of at least 150m should be maintained from the vehicle ahead in the same lane. When visibility is between 100m and 200m: Fog lights, low beam headlights, width indicator lights, and tail lights must be turned on. The speed should not exceed 60 km/h, and a following distance of at least 100m should be maintained from the vehicle ahead. When visibility is between 50m and 100m: Fog lights, low beam headlights, width indicator lights, and tail lights must be turned on. The speed should not exceed 40 km/h, and a following distance of at least 50m should be maintained from the vehicle ahead. Other lighting usage guidelines: High beam headlights: Use high beams when the road is poorly visible or there are no streetlights. Push the lighting control lever on the right side of the steering wheel backward to activate them. Low beam headlights: Use low beams when driving on well-lit urban roads or when encountering oncoming traffic or being overtaken by other vehicles. The lighting control knob on the dashboard can be turned to the low beam position. Turn signals: Used to alert surrounding vehicles and pedestrians when changing lanes, turning at intersections, making U-turns, overtaking, entering or exiting roundabouts, pulling over, or starting off. They should be activated in advance. Width indicator lights: Indicate the width of the vehicle in low-light conditions. They should be turned on during dusk, nighttime driving, or in low-visibility weather such as rain or fog. Hazard warning lights: Indicate emergency situations. They should be activated when temporarily parked, in case of vehicle malfunction or accident, or in low-visibility weather. Precautions for using lights in rainy weather: Keep lights on: During rainy days, especially at night, always keep your lights on. This ensures your own visibility and makes your vehicle more noticeable to others. Keeping lights on increases your vehicle's recognition among other drivers. Use low beam headlights: In rainy conditions, the rearview mirrors of the vehicle ahead may be wet and blurry. Besides turning on daytime running lights, it's advisable to use low beam headlights to enhance visibility in the mirrors of the vehicle ahead. Fog lights can also be turned on if necessary. Avoid high beam headlights: Except for driving on unlit highways at night with no vehicles ahead for a long distance, high beams should not be used at any other time. Especially during rainy nights, high beams can temporarily blind oncoming drivers, significantly increasing the risk of accidents. Use hazard warning lights: If the rain is heavy or there is standing water ahead, reduce speed and turn on hazard warning lights to alert following vehicles. However, when changing lanes with hazard lights on, first turn them off, activate the turn signal, and then change lanes to properly notify following vehicles and avoid changing lanes directly with hazard lights on.

18

0

Share

What Functions Should the Powertrain Have?

The powertrain has functions such as vehicle deceleration, speed change, reverse driving, power interruption, and inter-axle differential. The powertrain is the device that transmits power between the engine and the driving wheels, so it ensures the traction force, speed, and their coordinated changes required during vehicle operation. Below are the classifications of the powertrain: 1. Hydrostatic Powertrain: This type of powertrain can also be called a volumetric hydraulic powertrain. It mainly consists of an oil pump, hydraulic motor, and control device. This is a powertrain that converts the mechanical energy of the engine into hydraulic energy via the oil pump and then into mechanical energy via the hydraulic motor. 2. Hydraulic Powertrain: This combines hydraulic and mechanical methods to transmit power. In vehicles, hydraulic powertrain generally refers to hydraulic transmission, which uses liquid as the transmission medium and utilizes the kinetic energy changes generated during the circulating flow of liquid between the driving and driven components to transmit power. 3. Mechanical Powertrain: Compared to other powertrains, this one has a simple structure and reliable operation, which is why it is widely used in various types of vehicles. 4. Electric Powertrain: This mainly consists of an engine-driven generator. Since the generator is much heavier than the oil pump and hydraulic motor, its application is limited to ultra-heavy-duty vehicles.

19

1

Share

Why Are Used Santa Fes Cheaper?

In the used car market, the low resale value is the main reason why used Santa Fes are cheaper. Resale value is typically determined by factors such as brand, model, price fluctuation range, ownership volume, reliability, spare parts prices, and ease of maintenance. For the Santa Fe, the brand is the primary reason for its low resale value. Advantages of used cars: 1. Lower Price: Cars are consumable goods. For the same price, buying a used car allows you to experience high-end configurations that new cars don't offer, and you won't feel as bad about minor dents and scratches. Additionally, used cars have a relatively higher resale value. 2. High Resale Value: When selling a used car, the price is entirely dependent on the car's performance, which doesn't change over time. Therefore, the value of a used car is relatively stable. Disadvantages of used cars: 1. Outdated Exterior and Interior: The exterior and interior of a used car can't compare to a new car, and cheaper used models will have a significant gap compared to the latest models. 2. Lower Safety Than New Cars: The safety of used cars is much worse compared to new cars. Due to their lower safety, used cars also have a higher accident rate.

2

5

Share

What lights to use when a traffic accident occurs at night and is difficult to move?

What Are the Common Faults in New Energy Vehicles?

What are the reasons for the lack of acceleration in the Besturn X80?

What causes the hissing sound near the intake pipe of the Besturn X80?

Should Fog Lights Be Turned On in Rainy Weather?

What Functions Should the Powertrain Have?

Why Are Used Santa Fes Cheaper?

Will leaving the sunroof open and getting water inside affect the car?

What is the insurance process for an accident vehicle?

Can I still renew my driver's license if the renewal period has expired?

How to connect Bluetooth in Roewe ei5?